Wenger Percussion Workstation Assembly Instructions

Download this manual

ONTENTS

Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . .2

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Required Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Please read and understand these Assembly Instructions before working with or using the

Percussion Workstation.

Refer to the illustrations on the following pages. If you need additional information, write or

telephone Wenger Corporation at the number below.

©Wenger Corporation 2012

Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448

Questions? Call.....USA: 1-800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com

Percussion Workstation

Installing the Door Handles (Optional) . . . . . . . . . . . . . . . . . .3

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Music Desk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Suspended Cymbal Holder . . . . . . . . . . . . . . . . . . . . . .4

Cymbal Cradle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Printed in USA 08/12

Assembly Instructions

Part #147G300-04

Do you have a question about the Percussion Workstation and is the answer not in the manual?

Page 1: Assembly Instructions
Refer to the illustrations on the following pages. If you need additional information, write or telephone Wenger Corporation at the number below. ©Wenger Corporation 2012 Printed in USA 08/12 Part #147G300-04 Wenger Corporation, 555 Park Drive, P.O. Box 448, Owatonna, Minnesota 55060-0448 Questions? Call..USA: 1-800-4WENGER (493-6437) • Worldwide: 1-507-455-4100 • www.wengercorp.com...
Page 2 Wenger Corporation. Wenger Corporation does not assume any responsibility for any errors that may appear in this manual. In no event will Wenger Corporation be liable for technical or editorial omissions made herein, nor for direct, indirect, special, incidental, or consequential damages resulting from the use or defect of this manual.
Page 3 To assemble, attach the few remaining components as outlined in these instructions. • Read the complete assembly procedure before you begin. EQUIRED OOLS The following tools must be available to assemble the Percussion Workstation: • Phillips Head Screwdriver NSTALLING THE ANDLES PTIONAL 1.
Page 4 Percussion Workstation edge. YMBAL RADLE • Holds up to 22” cymbals in the ready-to-use position. • Vinyl-coated cradle, which protects and holds cymbals quietly, clamps to Percussion Workstation edge. Suspended Cymbal Holder and Cymbal Cradle are available as a set.