Weldex WDDS-1200S Quick Start Manual

4-SQUARE
B. Use the flush ELECTRICAL BOX
enclosure and mount
in a 4-square electrical
gang box in the ceiling
C. Use the flush
mount chassis and
surface dome cover
in a 4-square electrical gang
box on a solid surface
4-SQUARE
ELECTRICAL
BOX
Pull the power and video wires into the 4-square electrical box or
in through the base of the surface mount enclosure. If necessary,
attach conduit to the base of the enclosure and pull the wire in.
Mount the enclosure on a surface using the appropriate
hardware. Puncture the sealing washers with the mounting screws.
(Do not remove the sealing washers from the mounting holes)
If you are mounting directly to a wall or ceiling, it is recommended
that you use 1/4x20-inch hex-head bolts with wall anchors in high
vandalism applications. If you are mounting to a 4-square electrical
2
gang box, use 4 each 8-32 screws.
CONNECT THE VIDEO AND POWER
Connect the video cable to the BNC connector.
Depending on the power requirement of the camera (AC24V or DC12V),
connect the power wires to the appropriate input wires.
CAUTION
BE SURE TO CONNECT THE CORRECT POLARITY TO
3
THE CORRECT WIRE INPUT ON CAMERAS REQUIRING DC12V.
ADJUSTING THE CAMERA AND LENS
Loosen the camera mount tilt screws. Loosen the camera mount
pan and base screws.
Adjust the camera to the proper pan position and tighten
down the camera mount pan and base screws.
Adjust the camera to the proper tilt position and tighten
FOR VARIFOCAL LENS:
RAFTER Loosen the focal length and focus locking screws. Adjust according
CEILING to scene detail. Re-tighten the focal length and focus locking screws.
FLUSH DOME FOR FIXED LENS:
MOUNT If the lens is out of focus, loosen lens set screw and turn clockwise
or conterclockwise to focus.
4
SOLID SURFACE
INSTALLING DOME & TRIM RING
CONDUIT Be sure that all sealing washers are in place before mounting the trim
and dome cover.
FLUSH MOUNT Place dome over mounting plate. The screw holes will self-align.
CHASSIS AND The trim ring will "set" into place when holes are aligned.
SURFACE DOME Tighten the tamper-proof screws using the supplied L-Wrench.
COVER (This L-Wrench is not standard design, keep it for further use)
DIAGRAM
TOP VIEW
2
3
4
5
6
SEE SPECIFICATION SHEET FOR FURTHER DETAILS ON PARTICULAR MODELS.
1. SELF ALIGNING SCREW HOLES (3)
2. MOUNTING HOLES FOR DOUBLE
1
GANG BOX OR SURFACE MOUNT (8)
3. CAMERA MOUNT BASE AND
PAN SCREWS
4. CAMERA MOUNT TILT SCREWS
5. VARIFOCAL LENS LOCKING SCREWS
6. SURFACE MOUNT TRIM RING AND
DOME
7. FLUSH MOUNT TRIM RING AND
DOME
SIDE VIEW
7

TROUBLESHOOTING

ALL ADJUSTMENTS ARE MADE AT THE FACTORY FOR OPTIMAL
PERFORMANCE. THE FOLLOWING SETTINGS SHOULD ONLY BE USED IF
THESE ADJUSTMENTS DO NOT MEET THE REQUIREMENTS OF THE LOCATION
CONDITIONS.
VERTICAL PHASE (LINE LOCK)
To synchronize multiple cameras and prevent vertical
roll, adjust the vertical phase (line-lock).
See following diagrams for location of potentiometer. Turn
the potentiometer clockwise or counter-clockwise using a
small screwdriver.
AUTO IRIS LEVEL
Turn DC IRIS LEVEL control clockwise or counter-clockwise to adjust the
light level. (FOR CAMERAS WITH AN AUTO-IRIS LENS) The location of the
potentiometer is noted in the diagrams following.
BACK LIGHT COMPENSATION
Back light compensation (on) will allow the camera to filter out high gain background
light to obtain forground details. Switches on the dip switch module located
on the CCD board will provide adjustments for BLC (back light compensation).
See following diagrams for the location of this switch.
CAMERA DIP SWITCH / POTENTIOMETER SETTINGS
DSP COLOR
SURFACE MOUNT WDDS - 2400S
WDDS - 2405S
FLUSH MOUNT WDDF - 2400F
WDDF - 2405F
LOCATED
ON BACK OF BOARD
ON
DC IRIS LENS LEVEL
LINE - LOCK (PHASE)
1 2
BLC MODE (ON / OFF)
ELECTRONIC IRIS (ON - AE / OFF - ME)