Related Manuals for Nexersys PRO NXS-P
Summary of Contents for Nexersys PRO NXS-P
- Page 1 Model Assembly Manual Corporate Offices www.nexersys.com HArd BOdy. 500 San Marcos Street support@nexersys.com SHArp Mind.™ Suite 201 (877) 785-3823 Austin, TX 78702 (p–120713)
-
Page 2: Table Of Contents
Step 5: Body pad Assembly ................................12 Step 6: Head pad Assembly ................................13 Step 7: Mount CpU and Monitor to nexersys ..........................14 Step 8: Connect Accelerometer Cables ............................15 Step 9: Connect Audio and Video Cables ............................ 16 Step 10: Connect AC power Supply ............................... -
Page 3: Introduction
For best results, assemble the nexersys in the location where you intend to use it. Allow a workout area of at least 10ft by 6ft of free space for safe operation of the nexersys. Below are a few basic tips that will make your assembly of the nexersys quick and easy. -
Page 4: Important Safety Instructions
Safety instructions Be careful when dealing with larger nexersys components, as they might require effort to lift and attach. Some steps require two individuals. Have a second person assist you during assembly. Before using the nexersys, make sure that all screws have been tightened securely, as the nexersys will endure shock forces during most workouts. -
Page 5: Hardware List & Images
Model Assembly Manual Hardware List & images 1–M12 160 mm Bolt 2–M12 Flat Washer 8–M10 25mm Bolt 8–M10 Flat Washer 28–M8 20mm Bolt 2–M8 20mm Bolt 2–M8 Flat Washer 1–M12 nylock nut (fastened to each pad) 28–M8 Flat Washer 28–M8 Lock Washer... -
Page 6: Parts Images
Model Assembly Manual parts images nXS–p Assembly Manual (p–120713) -
Page 7: Parts Guide
Model Assembly Manual parts Guide item Quantity description Spine Handle Spine Support rubber Gasket Base Spine Left Head pad right Head pad Left Body pad (Kidney pad) Center Body pad right Body pad (Kidney pad) Left Kick pad... -
Page 8: Electronic Components
Model Assembly Manual Electronic Components 22” LCd Monitor HdMi to dVi Cable Audio Cable AC Cable AC power Brick USB Cable Sd Card nXS–p Assembly Manual (p–120713) -
Page 9: Step 1: Spine Support Assembly
Model Assembly Manual Assembly Step 1: Spine Support Assembly parts needed: Hardware needed: Base M10 25mm Bolt (4) Spine Support M10 Flat Washer (4) rubber Gasket nXS–p Assembly Manual (p–120713) -
Page 10: Step 2: Spine Assembly
Model Assembly Manual Step 2: Spine Assembly Additional parts needed: Hardware needed: Spine M10 25mm Bolt (4) rubber Gasket M10 Flat Washer (4) Spine Handle M12 nylock nut M12 Flat Washer (2) M12 160mm Bolt M8 20mm Bolt (2) M8 Flat Wahser (2) nXS–p Assembly Manual... -
Page 11: Step 3: Pad Attachment Overview
Model Assembly Manual Step 3: pad Attachment Overview Accelerometer cables must be connected to each pad before installation. Accelerometer cables are attached to the pad mounting bracket at the factory before the unit is shipped. When detaching the accelerometer cable from each individual arm, be sure not to let cable retract into the arm. - Page 12 Model Assembly Manual Step 3 Cont’d: Accelerometer When attaching the accelerometer cable to the accelerometer board, make sure the cable is oriented properly and the clip latches securely. nXS–p Assembly Manual (p–120713)
-
Page 13: Step 4: Kick Pad Assembly
Model Assembly Manual Step 4: Kick pad Assembly parts needed: Hardware needed: Left and right Kick pads M8 20mm Bolt (8) M8 Lock Washer (8) M8 Flat Washer (8) Warning: Be sure to install left and right kick pads with edge padding toward center of unit. -
Page 14: Step 5: Body Pad Assembly
Model Assembly Manual Step 5: Body pad Assembly parts needed: Hardware needed: Left Body pad M8 20mm Bolt (12) right Body pad M8 Lock Washer (12) Center Body pad M8 Flat Washer (12) Be sure to install center body pad with edge padding toward bottom of unit. Failure to do so will result in injury. -
Page 15: Step 6: Head Pad Assembly
Model Assembly Manual Step 6: Head pad Assembly parts needed: Hardware needed: M8 20mm Bolt (8) Left and right Head pads M8 Lock Washer (8) M8 Flat Washer (8) Warning: Be sure to install left and right head pads with edge padding toward center of unit. -
Page 16: Step 7: Mount Cpu And Monitor To Nexersys
Model Assembly Manual Step 7: Mount CpU and Monitor to nexersys note: Both the lock washer and flat washer are required for proper assembly. Warning: Be sure to install washers per instructions to avoid potential damage to the CpU. -
Page 17: Step 8: Connect Accelerometer Cables
Model Assembly Manual Step 8: Connect Accelerometer Cables note: plug-in left to right when facing back of monitor. Make sure the clip on the acceleromater cable faces the monitor when inserted. nXS–p Assembly Manual (p–120713) -
Page 18: Step 9: Connect Audio And Video Cables
Model Assembly Manual Step 9: Connect Audio, Video & USB Cables VGA port (not Used) nXS–p Assembly Manual (p–120713) -
Page 19: Step 10: Connect Ac Power Supply
Model Assembly Manual Step 10: Connect AC power Supply note: Connect dC Cable from AC power supply to dC cable at base of nexersys. nXS–p Assembly Manual (p–120713) -
Page 20: Step 11: Connect Dc Power Cables To Cpu And Monitor
Model Assembly Manual Step 11: Connect dC power Cables to CpU and Monitor note: The dC cable is routed through the spine of the nexersys Unit. nXS–p Assembly Manual (p–120713) -
Page 21: Step 12: Insert Sd Card
Model Assembly Manual Step 12: insert Sd Card note: insert Sd card into slot fully until spring mechanism locks Sd card into place. nXS–p Assembly Manual (p–120713) -
Page 22: Step 13: Turn On Power
Model Assembly Manual Step 13: Turn On power note: please wait at least 20 seconds for software license screen. CpU power Switch nXS–p Assembly Manual (p–120713) -
Page 23: Final Inspection
Model Assembly Manual Final inspection inspect your nexersys to ensure that all fasteners are tight and components are properly assembled. Failure to visually check and test assembly before use can cause damage to the equipment. it can also cause serious injury to users and bystanders. -
Page 24: Contacts
Model Assembly Manual Contacts TECHniCAL / CUSTOMEr SErViCE E-mail: support@nexersys.com phone: 877-785-3823 Website: www.nexersys.com COrpOrATE HEAdQUArTErS nexersys Corporation 500 San Marcos St. Suite 201 Austin, Texas 78702 phone: 877-209-0320 E-mail: info@nexersys.com Website: www.nexersys.com Serial number date of purchase nXS–p Assembly Manual... - Page 25 Head pads ar e i nst al led w i t h r ounded edge closest to moni to r . Turn on t he CPU. Navigate t hr ough t he Nexersys User I nter f ace w i t h touchsc r een or pads 1-5. Corporate Offices www.nexersys.com...
Need help?
Do you have a question about the PRO NXS-P and is the answer not in the manual?
Questions and answers