Charger Operation; Battery Packs - DeWalt XR LI-ION DCS388 Manual

English
electric shock. Removing the battery pack will not reduce
this risk.
• NEVER attempt to connect two chargers together.
• The charger is designed to operate on standard
230V household electrical power. Do not attempt to
use it on any other voltage. This does not apply to the
vehicular charger.
Charging a Battery (Fig. B)
1. Plug the charger into an appropriate outlet before inserting
battery pack.
2. Insert the battery pack
battery pack is fully seated in the charger. The red (charging)
light will blink repeatedly indicating that the charging
process has started.
3. The completion of charge will be indicated by the red
light remaining ON continuously. The battery pack is fully
charged and may be used at this time or left in the charger.
To remove the battery pack from the charger, push the
battery release button 8
nOTE: To ensure maximum performance and life of lithium-ion
battery packs, charge the battery pack fully before first use.

Charger Operation

Refer to the indicators below for the charge status of the battery
pack.
Charge Indicators
Charging
Fully Charged
Hot/Cold Pack Delay*
* The red light will continue to blink, but a yellow indicator light
will be illuminated during this operation. Once the battery pack
has reached an appropriate temperature, the yellow light will
turn off and the charger will resume the charging procedure.
The compatible charger(s) will not charge a faulty battery pack.
The charger will indicate faulty battery by refusing to light or by
displaying problem pack or charger blink pattern.
nOTE: This could also mean a problem with a charger.
If the charger indicates a problem, take the charger and battery
pack to be tested at an authorised service centre.
hot/Cold Pack Delay
When the charger detects a battery pack that is too hot or too
cold, it automatically starts a Hot/Cold Pack Delay, suspending
charging until the battery pack has reached an appropriate
temperature. The charger then automatically switches to the
pack charging mode. This feature ensures maximum battery
pack life.
A cold battery pack will charge at a slower rate than a warm
battery pack. The battery pack will charge at that slower rate
throughout the entire charging cycle and will not return to
maximum charge rate even if the battery pack warms.
The DCB118 charger is equipped with an internal fan designed
to cool the battery pack. The fan will turn on automatically
6
7 into the charger, making sure the
on the battery pack.
when the battery pack needs to be cooled. Never operate the
charger if the fan does not operate properly or if ventilation slots
are blocked. Do not permit foreign objects to enter the interior
of the charger.
Electronic Protection system
XR Li-Ion tools are designed with an Electronic Protection
System that will protect the battery pack against overloading,
overheating or deep discharge.
English
The tool will automatically turn off if the Electronic Protection
System engages. If this occurs, place the lithium-ion battery
pack on the charger until it is fully charged.
Wall Mounting
Cleaning

These chargers are designed to be wall mountable or to sit
WARNING: Blow dirt and dust out of the main housing
upright on a table or work surface. If wall mounting, locate the
with dry air as often as dirt is seen collecting in and around
charger within reach of an electrical outlet, and away from a
the air vents. Wear approved eye protection and approved
corner or other obstructions which may impede air flow. Use
dust mask when performing this procedure.
the back of the charger as a template for the location of the

WARNING: Never use solvents or other harsh chemicals
mounting screws on the wall. Mount the charger securely using
for cleaning the non-metallic parts of the tool. These
drywall screws (purchased separately) at least 25.4 mm long
chemicals may weaken the materials used in these parts.
with a screw head diameter of 7–9 mm, screwed into wood to
Use a cloth dampened only with water and mild soap.
an optimal depth leaving approximately 5.5 mm of the screw
Never let any liquid get inside the tool; never immerse any
exposed. Align the slots on the back of the charger with the
part of the tool into a liquid.
exposed screws and fully engage them in the slots.
Optional Accessories
Charger Cleaning Instructions

WARNING: Shock hazard. Disconnect the charger
WARNING: Since accessories, other than those offered
from the AC outlet before cleaning. Dirt and grease
by D WALT, have not been tested with this product, use
e
may be removed from the exterior of the charger using a
of such accessories with this tool could be hazardous.
cloth or soft non-metallic brush. Do not use water or any
To reduce the risk of injury, only D
cleaning solutions. Never let any liquid get inside the tool;
accessories should be used with this product.
never immerse any part of the tool into a liquid.
Consult your dealer for further information on the
appropriate accessories.

Battery Packs

Protecting the Environment
Important Safety Instructions for All
Separate collection. Products and batteries marked
Battery Packs
with this symbol must not be disposed of with normal
When ordering replacement battery packs, be sure to include
household waste.
catalog number and voltage.
Products and batteries contain materials that can
The battery pack is not fully charged out of the carton. Before
be recovered or recycled reducing the demand for raw
using the battery pack and charger, read the safety instructions
materials. Please recycle electrical products and batteries
below. Then follow charging procedures outlined.
according to local provisions. Further information is available at
READ ALL INSTRUCTIONS
www.2helpU.com.
• Do not charge or use battery in explosive atmospheres,
Rechargeable Battery Pack
such as in the presence of flammable liquids, gases or
dust. Inserting or removing the battery from the charger may
This long life battery pack must be recharged when it fails
to produce sufficient power on jobs which were easily done ignite the dust or fumes.
before. At the end of its technical life, discard it with due care for
• Never force battery pack into charger. Do not modify
our environment:
battery pack in any way to fit into a non-compatible
charger as battery pack may rupture causing serious
• Run the battery pack down completely, then remove it from
personal injury.
the tool.
• • Charge the battery packs only in D Li-Ion cells are recyclable. Take them to your dealer or a
local recycling station. The collected battery packs will be
DO NOT splash or immerse in water or other liquids.
•
recycled or disposed of properly.
• Do not store or use the tool and battery pack in
locations where the temperature may reach or exceed
40 ˚C (104 ˚F) (such as outside sheds or metal buildings
in summer).
WALT recommended
e
WALT chargers.
e