INTW Features: • wireless connection via Wi-Fi • communication in the 2.4GHz band • compliance with the IEEE 802.11b standard • data encryption: WEP, WPA, WPA2 • assigning a static or dynamic IP address (DHCP server) • built-in web server for configuration •...
INTW Table 1. Description of the components. Component Description LEDs – optical indication: – supply’s voltage – data transmission – receiving data RST button – reset the interface settings INIT button – initialization of the interface RP-SMA antenna socket SERIAL socket for connection with the power supply green LED light –...
INTW 4. Wi-Fi interface configuration. 4.1 The factory settings of the interface. Login page: Username - root Password - dbps IP address assigned automatically from the routers DHCP server Network’s name (SSID) No name Wi-Fi network connection Connecting to any available Wi-Fi network...
INTW 4.4 STEP 2 – The IP address configuration. For proper IP address change, it is recommended to turn off the firewall of the antivirus program for the time of configuration process. If the yellow LED [8 - fig.1] is permanently illuminated, make sure whether the interface has logged to the proper router.
Page 7
INTW Fig. 5. The window of network settings. In the settings window, select the „Manually configure network settings” option and change the IP address of the interface in the unblocked area to 192.168.1.101. The subnet mask and the default gateway IP address should be left unchanged.
INTW 4.5 STEP 3 – Setting the SSID for Wi-Fi network. Enter the network identifier, so that the RS485-WiFi interface will connect only with the designated router. To do that, log in to the router's configuration interface: open a web browser window and type the 192.168.1.1 in the address bar (default router address after the reset if not changed previously) and confirm by pressing the „ENTER”...
Page 9
INTW Fig. 8. The Wi-Fi interface login window. Type: Username: root Password: dbps Confirm by pressing the „Login” button. The adjustment window will be displayed. Fig. 9. The interface configuration panel. Choose the „Network” option from the „Configuration” group from the menu on the left side of the window.
Page 10
INTW Fig. 10. The “Wi-Fi LAN Settings” window”. Type the SSID network identifier that has been used during router configuration. Type: „PowerSecurity” in the „Network name” field. Configure the other settings as shown in the picture above and confirm by pressing the „Apply”...
Page 11
INTW Fig. 11. The „WiFi Security Settings” window. Next, in the „WPA PSK” section, enter any password in the „Passphrase” and „Confirm” fields. It will be used as a connection key. Type password e.g.: Passphrase: blackpower Confirm: blackpower Confirm by pressing the „Apply” button. The message informing about approved changes will be displayed.
INTW Fig. 12. The „Wireless Security” window Confirm the changes by pressing the „Save Settings” button and then confirm by pressing „Continue”. The Wi-Fi interface can be reset now. To do that, press the „Reset” button on the module or simply disconnect the power supply for a few seconds.
Page 13
INTW Select the "Port 1" once the window is loaded. Next, select „Custom” in the „Select Port Profile” field and confirm by pressing the „Apply” button. Fig. 14. The interface configuration panel – serial port parameters. After reloading the page, select the „Basic Serial Settings” tab at the bottom...
Page 14
INTW The power supply units of the EN54 series allow higher transmission speeds - instead of 19.2k 8E1 it can be set to 115.2k 8E1. The changed values apply to all settings. Fig. 15. The communication parameters of the serial port.
INTW Reset the Wi-Fi interface again. To do that, press the „Reset” button on the module or simply disconnect the power supply for a few seconds. After the reset, the connection between the interface and the router should be reestablished (the yellow LED is permanently illuminated).
INTW 5.2 Configuration of power supplies of the PSBEN series with LED display The PSU fitted with LED display enables setting the communication parameters of the serial port from the LED panel. To enter the setup mode, simultaneously press the „<,>” rightmost and leftmost buttons on the LED panel.
INTW 5.3 Configuration of power supplies of the EN54 series with LCD display The power supply units of the EN54 series allow higher transmission speeds - instead of 19.2k 8E1 it can be set to 115.2k 8E1. The changed values apply to all settings.
INTW 5.4 Configuration of power supplies of the EN54 series with LED display The PSU fitted with LED display enables setting the communication parameters of the serial port from the LED panel. 5.4.1 Setting the transmission speed - simultaneously press the „<,>” rightmost and leftmost buttons - The „tst”...
INTW 5.4.2 Setting the parity of the transmission - simultaneously press the „<,>” rightmost and leftmost buttons - The „tst” parameter will be displayed - use the „<” or „>” buttons to display the „trP” parameter - press „OK”...
INTW 6. Configuring the connection in the PowerSecurity program. For further configuration, the PowerSecurity program is required. The program can be downloaded at: http://www.pulsar.pl/pliki/PowerSecurity.exe The program is saved as an executable file and does not require installation. 1) Run the PowerSecurity.exe program.
INTW Fig. 18. The preview window of the PSU of the PSBEN (left) and EN54 series (right) 7. Technical parameters. Power supply 5V from the ”SERIAL” socket of the PSU Current consumption max 300mA TTL transmission speed Max 115200 bauds, with parity check...
Page 22
Waste electrical and electronic equipment must not be disposed of with normal household waste. According to the European Union WEEE Directive, waste electrical and electronic equipment should be disposed of separately from normal household waste. WARRANTY Pulsar K.Bogusz Sp.j. 5 years from the production date. Siedlec 150, 32-744 Łapczyca, Poland WARRANTY IS VALID only upon presentation of the original Phone (+48) 14-610-19-40, Fax.
Need help?
Do you have a question about the INTW and is the answer not in the manual?
Questions and answers