Controls/ Installation - Philips AJ3958/17B User Manual

English
CONTROLS (See figure 1 and 2)
CD PLAYER
1STOP 9
- stops CD playback;
- stops sleep function in CD mode;
- stops the active CD alarm for 24 hours.
2PLAY/ PAUSE 2;
- starts/ pauses CD playback.
3SEARCH ∞, §
- skips CD tracks/ searches for a particular passage.
GENERAL
4SLEEP
- activates and adjusts the sleep time.
5REPEAT ALARM/
BRIGHTNESS CONTROL
- changes the brightness of the display illumination;
- switches off the alarm for a 9 minute period;
- stops sleep function in CD, buzzer or radio mode.
6WEEKEND-SLEEPER
- deactivates alarm 1 and/ or 2 for the weekend.
7Display
- shows the clock/ alarm time and status of the set.
8ALARM 1 MODE/ OFF or ALARM 2 MODE/ OFF
- sets/ reviews/ switches off alarm 1 or 2.
RADIO
9ON/ OFF
- switches the radio on/ off;
- stops sleep function in radio mode;
- stops the active radio alarm for 24 hours.
0FM/ AM
- selects the radio waveband.
SETTING TIMES
!ALARM 1, ALARM 2, TIME
- sets the respective alarm or clock time
@7 , 8
- adjusts clock/ alarm times;
- adjusts the gentle wake minimum and maximum
volume level for alarm 1 or 2;
- selects a CD wake up track for alarm 1 or 2.
#VOLUME $, 3
- adjusts the sound level.
$Dial lens

CONTROLS/ INSTALLATION

%SET DAY
- sets the day for weekend sleeper activation.
^24 HR RESET
- stops the active buzzer, radio or CD alarms for 24
hours.
&LIFT TO OPEN
- opens/ closes CD door.
*TUNING
- tunes to a radio station.
(Pigtail - antenna to improve FM reception.
)Power cord - for AC power supply.
The type plate is located on the bottom of the set.
This product complies with the FCC-Rules, Part 15 and
with 21 CFR 1040.10. Operation is subject to the
following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received,
including interference that may cause undesired
operation.
CAUTION
Use of controls or adjustments or performance of
procedures other than herein may result in hazardous
radiation exposure or other unsafe operation.
INSTALLATION
Power Supply and Demo mode
1 Check if the power voltage, shown on the type plate
on the bottom of the set, corresponds to your local
power supply. If it does not, consult your dealer or
service center.
2 Connect the power plug into the wall outlet. The
power supply is now switched on and the display
will show the PHILIPS demo mode.
™ PH..IL..IPS scrolls across the display continuously.
• Press any control (with the exception of
REPEAT ALARM/ on the set) to
BRIGHTNESS CONTROL
exit the demo mode.
3 To disconnect the set completely from the power
supply, withdraw the power plug from the wall
outlet.
Standby power consumption (clock mode)...........3 W
SETTING TIMES, DAY
MEMORY BACKUP
The memory backup conveniently allows your day, alarm
and clock time settings to be stored for up to 3 minutes
when there is a power interruption e.g. AC power
failure.
The complete CD clock radio and illumination will be
switched off. As soon as the power supply returns, the
display will indicate the correct time.
• If power supply returns after 3 minutes, the display
will show the PHILIPS demo mode and you will
need to re-enter the day, alarm and clock times.
BASIC FEATURES
Illumination brightness
• Press REPEAT ALARM/
BRIGHTNES CONTROL
more.
™ The brightness of the display will change in this
sequence:
LOW MEDIUM BRIGHT LOW...
Volume
Press VOLUME $ or 3 to adjust the volume level. The
volume level UO: is indicated as a number from 0-32.
SETTING THE CLOCK AND ALARM TIMES
The time is displayed using the 12 hour clock where the
PM indicator lights up (on = PM, off = AM).
1 Press TIME, ALARM 1 or ALARM 2 briefly until the
respective clock or alarm time display flashes.
2 Press and hold down 7, 8 to adjust both the hours
and minutes.
• By pressing 7 or 8 respectively, the time increases/
decreases rapidly and continuously from minutes to
hours. Release 7 or 8 when you have reached the
correct setting.
• If you need to adjust the time slowly, minute by
minute, press 7 or 8 briefly and repeatedly.
3 Press TIME, ALARM 1 or ALARM 2 to confirm your
respective time setting.
SETTING THE DAY
Setting the day enables you to set the WEEKEND-
SLEEPER function. If you attempt to use the
WEEKEND-SLEEPER prior to setting the day (Monday
to Sunday, 1-7) will show briefly in the display to
remind you to set the day first.
1 Press SET DAY.
2 While the day display is shown, press SET DAY
again once or more to select the day numbered from
dAY 1-7 (Monday-Sunday):
™ The display will revert to show the clock time.
CD PLAYBACK
once or 1 To open the CD door, lift at the edge marked
LIFT TO OPEN.
2 Insert a CD with the printed side facing up, and close
the door.
3 Press PLAY/ PAUSE 2; to start playback.
™ The CD indicator , Cd:-- and the total
CD
number of tracks are shown, followed by the first
track number before returning to clock time.
– door is shown if you have not closed the CD
door/ open the CD door during playback.
– noCd is shown if no CD has been inserted/
inserted incorrectly.
– nFCd is shown if the CD-R(W) is non-finalized
– Err indicates a general error in operation of the
set.
™ The display returns to clock time.
4 Adjust the sound with VOLUME $ or 3.
5 To interrupt, press PLAY/ PAUSE 2;.
• The current track number shows briefly before
returning to clock time. flashes during pause.
CD
6 Press PLAY/ PAUSE 2; again to resume playback.
7 Press STOP 9 to stop playback.
™ The display returns to clock time.
CD