Advertisement
Available languages
Available languages
These operating instructions are an integral part of the
product, and contain important information and safety
notes. Please keep them in a safe place at all times, and be
sure to pass them on to the new owner if you ever dispose
of the product.
1.
S
PECIFICATION
SAFETY-SWITCH
Order Number
Input voltage
Power supply
2S LiPo or
5 NiXX* cells
Battery backer
Output voltage
Max. cont. current
• With 2S LiPo
• With 5 NiXX cells
Max. continuous
dissipated regulator
power
Battery connecting
0.34 mm² with M6
leads
connector system
Receiver leads
Dimensions
(L x W x H)
45 x 17 x 17 mm
Weight incl. leads
approx. 25 g
and connectors
Idle current drain
approx. 5 µA
Operating
temperature
*
NiXX = NiCd or NiMH batteries
2.
S
N
AFETY
OTES
Read the instructions before use
Use only for the intended range of applications (
Power supplies must of adequate capacity (
Observe the installation notes (
Keep to the following sequence when switching on:
First switch transmitter ON, then switch receiver ON.
First switch receiver OFF, then switch transmitter OFF.
Disconnect the battery or batteries (
Disconnect the battery or batteries from the SAFETY-
SWITCH LiPo (TwinBatt) if you do not intend to use the
model for a protracted period.
These devices must never be connected to a mains PSU!
MULTIPLEX Modellsport GmbH & Co.KG • Westliche Gewerbestraße 1 • D-75015 Bretten (Gölshausen) • www.multiplex-rc.de
Operating Instructions
SAFETY-SWITCH LiPo and SAFETY-SWITCH LiPo TwinBatt
LiPo
LiPo TwinBatt
# 8 5062
# 8 5063
Maximum 8.4 V
2 x 2S LiPo or
2 x 5 NiXX* cells
no
yes
5.5 V stabilised (+/- 0.1 V)
2.0 A
5.0 A
5.0 W
2 x 0.34 mm² with M6
connector system
2 x 0.34 mm², UNI system
approx.
approx.
51 x 20 x 26 mm
approx. 45 g
approx. 5 µA per
battery
- 10° C ... + 75° C
7.4)
6.)
11.)
3.
A
PPLICATIONS
The SAFETY-SWITCH LiPo and SAFETY-SWITCH LiPo
TwinBatt are ultra-modern electronic switch harnesses / power
supply systems. They are intended exclusively for use in model-
ling applications.
It is prohibited to use these devices for applications such as
man-carrying aircraft or industrial equipment.
4.
S
PECIAL
SAFETY-SWITCH LiPo and SAFETY-SWITCH LiPo TwinBatt:
•
Electronic switch harnesses.
•
Much more robust than conventional mechanical switches,
as they are not susceptible to vibration, wear or contact cor-
rosion problems.
•
Extremely rugged plastic housing, large heat-sink for voltage
regulator, high-flex connecting leads.
•
Power supply for servos and receiver optionally from 2S LiPo
or 5-cell NiXX battery.
•
Linear IC-controlled stabilisation generates a stabilised out-
put voltage of 5.5 V, corresponding to a fully-charged four-
cell NiXX battery. This ensures that the servos operate at
constant speed and torque over the full period of operation -
an important requirement for high-quality aerobatics.
•
Battery connection via encapsulated MPX high-current con-
nectors (M6 system).
•
Two receiver connecting leads (UNI system) for maximum
possible security, with double conductor cross-section and
twice the number of electrical contacts.
•
Three-colour LEDs provide constant visual four-stage indi-
cation of receiver battery voltage.
•
Simple, carefully thought-out power-on procedure: an inter-
nal program ensures completely secure switching processes;
it is impossible to switch the harness on or off accidentally.
The SAFETY-SWITCH LiPo TwinBatt also offers:
•
High-performance integral battery backer, permitting the use
of two receiver batteries (
•
One sensor button for each power circuit, with security but-
ton. Each power circuit can be switched on and checked in-
dividually.
•
Two linear voltage regulators - one for each battery input.
•
Two electronic switches - one for each power circuit.
•
Two voltage monitors for monitoring the two batteries.
•
Two three-colour LEDs for four-stage display of the voltage
of both batteries.
•
Two minimum value (low voltage) memories, can be read out
3.)
separately for each battery.
F
EATURES
9.2.4).
Page 1/6
Advertisement
