ProFitter RMC-FA300PF Operating Instructions & Parts Manual page 2

ProFitter Operating Instructions and Parts Manual
TM
ProFitter
Propane Construction Heater
MATERIALS, PAPER OR CARDBOARD, A SAFE
DISTANCE AWAY FROM THE HEATER AS
RECOMMENDED BY THE INSTRUCTIONS.
E
NEVER USE THE HEATER IN SPACES WHICH
N DO OR MAY CONTAIN VOLATILE OR
AIRBORNE COMBUSTIBLES, OR PRODUCTS
G
SUCH AS GASOLINE, SOLVENTS, PAINT
L
THINNERS, DUST PARTICLES OR UNKNOWN
CHEMICALS.
I
WARNING
S
H This product and the fuels used to
operate this product (liquid propane),
and the products of combustion of
such fuels, can expose you to chemicals
including benzene, which is known to
the State of California to cause cancer
and reproductive harm.
For more information go to
www.p65Warnings.ca.gov
Using this heater in a
residential garage
requires that the heater is positioned
so that it is protected against any possible
damage by a moving vehicle, etc. It must be
positioned so that the base of the heater is
no less than 18 in (450 mm) above the
garage floor or 8 ft (2450 mm) in repair
garages. The heater must be placed on a
stable surface. Do not place it on a chair,
ladder, etc. Raising the heater will reduce
BUT NOT eliminate the possibility of lighting
the vapor of any flammable liquids which
may be improperly stored or accidentally
spilled. If the smell of gasoline is present,
DO NOT operate this heater until the area
has been properly ventilated.
Not for home or rec-
reational vehicle use.
The heater is designed and approved
for use as a construction heater
under ANS Z83.7 CSA 2.14. It is hard
to anticipate every use which may
be made of this heater. CHECK WITH
YOUR LOCAL FIRE SAFETY AUTHORITY
IF YOU HAVE QUESTIONS ABOUT
APPLICATIONS.
Other standards govern the use of fuel
gases and heat producing products in
specific applications.
Your local authority can advise you
about these.
For Technical Support or Troubleshooting, Call: 1-877-447-4768, 8:30 am - 4:30 pm CST
TM
IMPORTANT: READ THIS USER'S
MANUAL CAREFULLY AND
COMPLETELY BEFORE TRYING TO
OPERATE OR SERVICE THIS HEATER.
IMPROPER USE OF THIS HEATER CAN
CAUSE SERIOUS INJURY OR DEATH
FROM FIRE, EXPLOSION AND CARBON
MONOXIDE POISONING.
This is a direct-fired forced air
construction heater for either indoor
construction or outdoor use. Its
intended use is primarily the temporary
heating of buildings or structures under
construction, alteration or repair. All
the products of combustion generated
by the heater are forced through the
heater and released into the area
being heated. This heater operates
at approximately 98%+ combustion
efficiency but still produces a small
amount of carbon monoxide. Humans
can tolerate small amounts of carbon
monoxide for short periods. Carbon
monoxide can build up in a heated
space and failure to provide adequate
ventilation could result in poisoning or
death.
For either indoor or outdoor use.
Adequate ventilation shall be provided
in accordance with OSHA 29 CFR
1926.154, Safety Requirements for
Temporary and Portable Space Heating
Devices and Equipment ANSI A10.10,
ANSI 223.1 / NFPA 54, Liquified
CSA 2.14b-2009, ANS Z83.7b-2009.
Petroleum Gas Code, NFPA 58 or the
National Gas and Propane Installation
Code, CAN B149.1 as appropriate.
IMPORTANT SAFETY INFORMATION
• Children should be carefully
supervised, when they are in the area.
• Always maintain proper clearance
from combustible materials. Minimum
clearance from combustibles:
Side - 24" (61cm); Top - 72" (1.8 m);
Front - 96" (2.4 m). Floor - combustible.
Not for use on finished floors.
• Heater must be placed on level and
stable surface.
• Never place anything including clothes
NEVER LEAVE THE HEATER
UNATTENDED WHILE BURNING!
or other flammable items on the heater.
• The appliance area shall be kept clear
and free from combustible materials,
gasoline and other flammable
vapours and liquids.
• Do not modify or operate a heater
which has been modified.
• Adequate clearance for accessibility
and for combustion & ventilation air
supply must be maintained at all
times when the heater is operating.
• Service and repair should be done by
a qualified service person. The heater
should be inspected before each use
and at least annually by a qualified
person. More frequent cleaning may
be required as necessary. Do not service
while hot or operating.
• Never connect heater to an
unregulated gas supply.
• The heater is shipped from the
factory for LP(Propane) gas. This heater
is for use with propane gas only, do
not convert heater to any other gas.
Installation must conform to local
codes or, in the absence of local codes,
with the standard for the Storage and
Handling of Liquefied Petroleum Gases
ANSI/NFPA 58 and the Natural Gas and
Propane Installation Code CSA B149.1
• The minimum and maximum inlet
pressures to the regulator from the
gas tank are 5 psi and bottle pressure,
respectively. Use only the regulator
& hose assembly provided with the
heater. Inspect the regulator/hose
assembly prior to each use of the
heater. If there is excessive abrasion
or wear, or hose is cut, replace with
regulator/hose assembly listed on the
parts list prior to using this heater.
• Gas supply connections should be
checked using a 50/50 solution of liquid
dish soap and never use a flame to
check for gas leaks.
2
RMC-FA300PF
www.ghpgroupinc.com