Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Digga 4 in 1 Kubota BX Bucket
Summary of Contents for Digga 4 in 1 Kubota BX Bucket
- Page 1 KUBOTA BX BUCKET OPERATORS & PARTS MANUAL PM-000052-A...
- Page 2 PM-000052-A KUBOTA BUCKET NOVEMBER 2017...
-
Page 3: To The Purchaser
Optional Extras are available for special applications or extreme conditions: these are noted throughout the manual. Contact your DIGGA dealer for any further information pertaining to this product or for further information on other products available in the DIGGA range. -
Page 4: Table Of Contents
SAFETY STICKER LOCATION............12 SPARE PARTS................... 13 TROUBLESHOOTING................ 16 SAFETY - GENERAL PRECAUTIONS..........18 SAFETY-WORKING WITH THE ATTACHMENT........ 21 WARRANTY..................22 MODELS COVERED IN THIS MANUAL 4 in 1 Kubota BX Bucket DIMENSIONS WEIGHT Width (bucket cutting) 1225mm 48” BX Bucket... -
Page 5: Preparation For Use
To avoid any inconvenience before operation, please check that you have received the following items which you may have ordered in your Kubota BX Bucket 3rd service kit DESCRIPTION 4 IN 1 KUBOTA BX BUCKET WIRING HARNESS ASSEMBLY HOSES HYDRAULIC VALVE KIT... -
Page 6: Installation And Operating Instructions
& load ratings of the original machine it was purchased for. For fitment of the Kubota BX Bucket to other machines you must first contact your DIGGA dealer and receive written confirmation to ensure you do not incorrectly fit the Kubota BX Bucket to a machine with higher, pressure or rated load capacities than what the Kubota BX Bucket was designed for. - Page 7 INSTALLATION OF KUBOTA BX BUCKET KIT FOR KUBOTA BX TRACTOR This bucket and kit was developed to enable a Digga 4-in-1 bucket to be adapted to a Kubota BX mini tractor without the need of engaging hydraulics and auto electrical specialists. The Owners Manual for this BX bucket kit does not cover the Kubota tractor and its controls and maintenance. Please refer to the Kubota tractor owners manual for safe operation.
- Page 8 INSTALLATION AND OPERATING INSTRUCTIONS MOUNTING THE HYDRAULIC SOLENOID VALVE BLOCK With bucket and arm at rest on the ground, disconnect the white and yellow quick release couplings (found under the right hand side of the boom FIG 1). Under the right hand side of the lift boom you will find where the hydraulic hoses connect to steel tubes, this is where the soleniod valve is to be mounted and connected into.
- Page 9 INSTALLATION AND OPERATING INSTRUCTIONS OPERATING PROCEDURES WARNING: DO NOT OPERATE THE KUBOTA BX BUCKET BEFORE READING THE INSTRUCTIONS BELOW OPERATING THE KUBOTA BX BUCKET USING THE JOYSTICK CONTROLLER Boom Down Start the Machine; adjust the engine speed above idle. Proceed to lift and crowd the bucket by moving the joystick as follows.
-
Page 10: Maintenance
NO responsibility for loss or damage to persons or property in any regard can be attributed to Digga. - Page 11 MAINTENANCE BEFORE EACH USE ● Make sure that all nuts and bolts are in place and properly tightened. ● Make sure that all other fasteners are in place and are performing their specified function. ● Make sure that all hydraulic fittings are tightened and that there are no leaks in any fittings or hoses. ●...
-
Page 12: Safety Sticker Location
Replace all missing, illegible, or damaged safety signs. ● Replacement parts for parts with safety signs attached must also have safety signs attached. ● Safety signs are available from your dealer or from Digga Australia. ORDER CODE DESCRIPTION DE-000129 Decal-Pinch Point DE-000055 Decal-Pressure Tested DE-000046... -
Page 13: Spare Parts
SPARE PARTS Bucket Spares NDER BUSH (OBSOLETE) (OBSOLETE) SOLETE) NT - 1225mm NO ORDER CODE DESCRIPTION ELDMENT - BU-001869 BUCKET- LIGHT MINI - FLOATING CYLINDER BUSH BU-000085 BUCKET - MINI - CLEVIS PIN BOTTOM 1.5 IN SHAFT BU-000077 BUCKET - MINI - CLEVIS PIN CYLINDER BU-000084 BUCKET - MINI - CLEVIS PIN MAIN BU-001896... - Page 14 Parts List ITEM PART NUMBER DESCRIPTION SPARE PARTS FA-000067 BOLT HEX 5/16 x 3.1/2 G8 UNC ZINC PLATED NOTE THIS HOSE MUST BOLT Hydraulic Spares TO THE BOTTOM TEE FITTING FA-000094 NUT NYLOC 5/16" ZINC PLATED NOTE THIS HOSE MUST BOLT TO ON THE BACK OF THE BUCKET THE BOTTOM TEE IN THE BUCKET FA-000492...
- Page 15 SPARE PARTS Electrical Spares ORDER CODE DESCRIPTION EC-000093 ASSEMBLY - CONTROLLER FOR BX LOADER EC-000005 ELECTRICAL COMPONENT - KUBOTA WIRE HARNESS COMPLETE WITH DIN CONNECTOR & 10A INLINE FUSE...
-
Page 16: Troubleshooting
Damage to cylinder Inspect and Repair or Replace. Damage to Bucket Abuse Contact your local Digga dealer. Bucket not fitting to parent machine correctly Contact your local Digga dealer. Bucket Movement in reverse Hose Nº 2 and Hose N° 5 may be connected to Hose N°... -
Page 18: Safety - General Precautions
Take the time to read these messages as you come across them. The DIGGA Kubota BX Bucket receives its power from the Parent Machine through the Auxiliary Valve circuit with Quick Release Couplers normally located on the machine arms near the front. - Page 19 SAFETY PRECAUTIONS - GENERAL INFORMATION Never operate the attachment without first reading and understanding the entire operator’s manual. Do not paint over, remove or deface any safety signs or warning decals on your equipment. Follow all safety decals. Keep them clean and replace them if they become worn, damaged or illegible. Know your equipment inside and out.
- Page 20 Make no modifications to your Kubota BX Bucket. ● When making repairs, use only genuine Digga parts for fasteners, hydraulic hoses, or hydraulic fittings, use only properly rated parts. ● Replacement parts, for parts with safety signs attached, must also have safety signs attached.
-
Page 21: Safety-Working With The Attachment
● Always close the floor securely against the bulldozer weldment before setting the unit down on the ground. For additional safety information please see Risk Management booklet. To obtain a copy contact Digga Head Office on +61 7 3807 3330... -
Page 22: Warranty
Digga may request defective product or products be returned prepaid to them for inspection at their place of business or to a location specified by Digga. The warranty will be considered void if the product or any part of the product is modified or repaired in any way not expressly authorized by Digga, or if closed components are disassem- bled prior to return. -
Page 24: In 1 Kubota Bx Bucket
P h : 0 3 9 7 0 6 6 1 7 1 P h : 0 8 9 4 5 7 1 5 4 4 Web: www.digga.com Email: info@digga.com PM-000052-A KUBOTA BUCKET NOVEMBER 2017 Product Manual: 4 IN 1 KUBOTA BX BUCKET Part No: PM-000052-A...
Need help?
Do you have a question about the 4 in 1 Kubota BX Bucket and is the answer not in the manual?
Questions and answers