Advertisement
English
Controls (see figure 1)
1 SET TIME – adjusts clock time
2 ALARM 1
– ON – switches on ALARM 1
– SET – adjusts alarm time of ALARM 1
– OFF – switches ALARM 1 off
3 REPEAT ALARM – switches off alarm for
a 6-minute period
4 Display – shows the clock/ alarm time or
CD tracks
5 ALARM 2
– ON – switches on ALARM 2
– SET – adjusts alarm time of ALARM 2
– OFF – switches ALARM 2 off
6 LIFT TO OPEN – lift here to open / close
CD door
7 TUNING – tunes to a radio station
8 STOP 9 – stops CD playback
9 PLAY / PAUSE ); – starts / pauses CD
playback
0 MIN ∞ / HOUR §
– adjusts clock / alarm time
– skips CD tracks / searches for a particular
passage
! FM•MW•BUZ•CD
– selects FM, MW or CD sound source
– selects radio, buzzer or CD alarm mode
@ POWER / ALARM RESET
– switch the set ON / OFF
– stops the active alarm for 24 hours
– switch off the sleep timer
# SLEEP
– adjusts timer options for radio / CD
playback
– switches on radio or CD for timer mode
$ VOLUME – adjusts sound level
Controls/ Power supply
% Battery compartment – insert a 9 volt
battery, type 6F22 (not supplied) for clock
memory backup
^ RESET – use ballpointpen to press button if
the set/display does not react on any of the
controls
& Power cord – connects to wall outlet
* Pigtail – improves FM reception.
Power supply
1 Check if the power voltage as shown on
the type plate on the base of the set cor-
responds to your local power supply.
2 Connect the power plug to the wall outlet.
The power supply is now switched on and
the numbers on the display shows 0:00.You
will need to set the correct time.
3 To disconnect the set from the power supply
completely, unplug from the wall outlet.
Standby power consumption
(clock mode) . . . . . . . . . . . . . . . . . . . .. . . . 1.6W
The type plate is located on the bottom
of the set.
For users in the U.K., please follow the
boxed instructions 'Important notes...' on
this sheet.
Clock
Clock memory backup
When a power failure occurs, the complete
clock radio will be switched off. When the
power supply returns, the time display shows
0:00 and you will need to reset the correct
time on the clock.
To retain the clock time and the set alarm
time(s) in the event of an AC power failure
or disconnection, insert a 9 volt battery
(suggest to use type 6F22, not supplied) into
the battery compartment: this will act as a
clock memory backup. However, the time will
not be illuminated on the clock display.
Operation of the alarms, FM / MW radio and
CD are also excluded. As soon as the power
supply returns, the display will indicate the
correct time.
1 Connect the power plug to the wall outlet.
2 Insert the battery into the battery compart-
ment.
•
Replace the battery once a year, or as often
as necessary.
Batteries contain chemical substances,
so they should be disposed of properly.
Setting the clock
Clock display
The time is shown and the display also
indicates whether you have switched on the
alarm(s), and these indicators will light up
respectively next to AL1 and AL2 on the
display.
The time is displayed using 24 hours clock.
1 Press and hold down the SET TIME button.
2 Simultaneously, press and hold down MIN
∞ or HOUR § to adjust the minutes or
hours.
3 Release SET TIME and MIN ∞ / HOUR
§ when you have reached the desired
setting.
Radio/CD Player
Radio
1 Press POWER to switch on.
➜ POWER button lights up.
2 Use FM•MW•BUZ•CD slider to select FM
or MW waveband.
3 Use TUNING (on the side panel) to find
your station.
4 Adjust the sound with the VOLUME
control.
5 Press POWER to switch off.
➜ POWER button light will turn off.
To improve reception:
FM: Extend and position the pigtail fully to
obtain optimal reception.
MW: Uses a built-in antenna. Direct the
antenna by adjusting the position of
your unit.
This set complies with the radio
interference requirements of the European
Community.
CD playback
This CD clock radio can play only audio discs
including CD-recordables. Do not try to play
a CD-ROM, CD-RW, CDI,VCD, DVD or
computer CD.
1 Open the CD door.
2 Insert a CD with printed side facing up, and
close the CD door.
3 Press POWER to switch on.
➜ POWER button lights up.
4 Select CD by using the FM•MW•BUZ•CD
slider.
5 Press PLAY / PAUSE ); to start playback.
➜ Display shows current track number
briefly.
Advertisement
