Table of Contents
Advertisement
Quick Links
Parts and Accessories
Installation Instructions
BMW Apollo / Classic car phone upgrade kit
BMW 5 Series touring (E 39/2) from 09/01
These installation instructions are only valid for cars with SA 640
The installation time is approx. 2.5 hours, but this may vary depending on the condition of the
car and the equipment in it.
Retrofit kit: 84 61 0 143 793
Retrofit kit No. 84 61 0 143 793
Installation Instructions No. 01 29 0 144 350
Issue date: 12.2001
F 39 0554 2W
Advertisement
Table of Contents
Related Manuals for BMW Apollo
Summary of Contents for BMW Apollo
- Page 1 Parts and Accessories Installation Instructions F 39 0554 2W BMW Apollo / Classic car phone upgrade kit BMW 5 Series touring (E 39/2) from 09/01 These installation instructions are only valid for cars with SA 640 The installation time is approx. 2.5 hours, but this may vary depending on the condition of the car and the equipment in it.
-
Page 2: Table Of Contents
Contents Section Page Important information ..........Preparations . -
Page 3: Important Information
The target group for these installation instructions is specialist personnel trained on BMW cars with specialist knowledge of vehicle electrical systems. Work: All servicing, repair and installation work on BMW cars is completed at your own risk. All work is to be carried out using current BMW - Repair manuals... -
Page 4: Preparations
Preparations TIS instruction No. Conduct a brief test Disconnect the negative pole of the battery 12 00 ... The following components must be removed first of all: Left boot – wheel arch trim 51 47 151 Fresh air grille in the rear 64 22 190 Armrest (no longer required) Hands-free microphone trim... -
Page 5: Installation And Cabling Diagram
Installation and cabling diagram 039 0063 Z Legend Hands-free microphone Eject box and interface Adapter eject box Transceiver module Transceiver module adapter EN/5 Retrofit kit No. 84 61 0 143 793 Installation Instructions No. 01 29 0 144 350 Issue date: 12.2001... -
Page 6: Connection Diagram
Connection overview 053 0104 Z Cable colour Abbreviation / Item Description Signal / Cross- Connection location in the car Slot section Adapter eject box Between the standard wiring harness and interface Black 18-pin plug To interface X4545 Black 18-pin plug To standard wiring harness X4545 Hands-free control module... -
Page 7: To Install And Connect The Hands-Free Control Module
To install and connect the hands-free control module Insert the transceiver module (1) into the holder (2) and secure it with the bar (3). 039 0064 Z Bolt the holder with the transceiver module (1) to the body stud (3) on the left-hand side of the boot using hexagonal screws M5 (2). - Page 8 To install and connect the hands-free control module Release the tied back plugs X18618 and X18626 X18618 from the standard wiring harness. Connects branches B1 and B2 to plugs X18618 and X18626 . X18626 039 0124 Z EN/8 Retrofit kit No. 84 61 0 143 793 Installation Instructions No.
-
Page 9: To Install And Connect The Eject Box
To install and connect the eject box Clip the eject box (1) into the supplied armrest (2). 039 0059 Z Place the slide plate (1) on the armrest (2) and secure it with Philips screws (3). 039 0060 Z Bolt the holder (1) for the interface to the centre console (2) with Philips screws (2). - Page 10 To install and connect the eject box Connect the black 6-pin plug (1) for the eject box to the black 6-pin plug (2) for the interface. 038 0068Z The adapter cable A must be fitted. Connect the adapter cable A between the black 18-pin plug for the interface and plug X4545 on the standard wiring harness.
-
Page 11: To Install The Hands-Free Microphone
To install the hands-free microphone Cars without SA 401 only Release the tied back plug X4221 from the standard wiring harness and connect it to the hands-free microphone (1). The arrow on the hands-free microphone (1) must point to the front of the car. Clip the hands-free microphone (1) into the trim (2). -
Page 12: Concluding Work And Coding
Concluding work and coding This upgrade system does not require coding. - Conduct a brief test with DIS/MoDiC. - Conduct a function test - Assemble the car again following the instructions to dismantle it in reverse order. If necessary, the circuit diagram for the telephone preparation (SA 640) and for the adapter cables can be taken from the installation instructions entitled “Telephone upgrade circuit diagrams, part No.