SOMFY inteo CENTRALIS UNO RTS Installation Manual

centralis uno RTS_9007504D 30/08/06
b Programming the 2nd intermediate position (IP2)
Set the blind to its DOWN limit before programming in order to always have the same adjustment.
2
1
after
DOWN
3 seconds
• Press the ▲ and ■ button simulta-
• Move the shutter/blind at its DOWN
limit with the ▼ button and immedia-
neously until the shutter/blind begins
tely press the ■ button briefly.
to move DOWN.
c Operating
1st intermediate position 2nd intermediate position
UP limit
IP1
DOWN limit
• Press briefly the ■ button while the blind is at
• Press briefly the ■ button while the blind is
its DOWN limit.
at its UP limit.
➜ The shutter/blind will move up and stop at the
➜ The shutter/blind will move down and stop
2nd intermediate position.
at the 1st intermediate position.
d
Delete the intermediate position
If you record a new IP , this will automatically erase the previous one.
If you want to erase without recording a new one, Press briefly on the ■ button to reach the IP , then:
To erase the 1st intermediate position, press ■ button for more than 5 seconds.
To erase the 2nd intermediate position, press ■ button for more than 5 seconds.
➜ The shutter/blind jogs briefly (UP/DOWN) indicating that CENTRALIS uno RTS has deleted the intermediate position.
5
Complete reset
To completely reset the CENTRALIS uno RTS, press its PROG button for more than 7 seconds.
P This will erase all of the programmed controls, the intermediate positions.
R
O
G
➜
The shutter/blind jogs twice (UP/DOWN), the memory of the CENTRALIS uno RTS is cleared.
7 sec.
6
Trouble shooting guide
Nothing works: Phantom intermediate position:
Check the motor. The programmed IP can only be reached from the
UP or DOWN limits. not when the shutter is in ano-
Check the power supply.
Check the battery of the transmitter. ther position.
Check that the transmitter has been properly
recorded in the CENTRALIS uno RTS's memory.
Check for any other possible source of radio
interferences.
4
CENTRALIS uno RTS
17:17 Page 1
3 4
5 sec.
STOP
• Press the ■ button more than 5 sec.
• Stop the shutter/blind at the inter-
➜ The shutter/blind jogs briefly
mediate position you wish.
If necessary, adjust this position with (UP/DOWN), the 2nd intermediate posi-
the ▲ or ▼ buttons.
tion is recorded.
IP2
Lost in your programming mode:
Just make a complete reset and start again
(refer to section 5).
We reserve the right to make changes due to technical improvements.
SOMFY SAS, capital 20.000.000 Euros, RCS Bonneville 303.970.230
INSTALLATION
inteo
IP2
CENTRALIS UNO RTS is an individual control system for AC motor dedicated to roller shutters
and interior blind applications.
• CENTRALIS UNO RTS has an integrated radio receiver compatible with the RT and RTS
transmitters allowing individual, group and master commands. Up to twelve controls can be
recorded in the CENTRALIS UNO RTS memory.
• The commands coming from the radio controls can be disabled thanks to the 0/auto switch.
• One or two intermediate positions can be programmed.
• Compatible with sensor (sun protection functionning only) Up to three sensors can be recorded.
1
Characteristics
80 mm
2
Installation
This device must be installed and programmed by qualified installers for whom this instruction is inten-
ded. Before connecting the unit, read the instructions carefully.
Assembly
2.1
FRONT PLATE
FRAME
CONTROL UNIT
We reserve the right to make changes due to technical improvements.
guide
CENTRALIS UNO RTS
• Main supply : 220-240V 50Hz.
• Class II product
• Protection index IP40.
80 mm • Output : 250V~ 3A
• Output temporisation : activ for 180s.
• Environmental conditions for use :
- temperature 0°C to +40°C (no condensation allowed).
- pollution degree typical for usual living space.
33 mm 17 mm
Hereby, SOMFY, declares that this equipment
is in compliance with the essential require-
ments and other relevant provisions of
Directive 1999/5/EC.
A Declaration of Conformity is available at the
web address www.somfy.com Heading CE
The range of radio control is limited by laws regulating
BRACKET radio devices and by building design.
When planning, please ensure that there is adequate
radio reception.
In order not to affect quality of reception, a minimum
distance of 30 cm between a CENTRALIS uno RTS
and a radio transmitter should be maintained.
CENTRALIS uno RTS should not be installed in the
WALL
immediate vicinity of metal surfaces. Powerful local
transmitter equipment (e.g. cordless headphones) with a
transmission frequency identical to the CENTRALIS
uno RTS can affect its function.
CENTRALIS uno RTS
1