Loading Your Cabinet; Operating The Interior Lights; Efficient Use; Exterior Cleaning - PRODIS NT Series User Manual

PART III

LOADING YOUR CABINET

ALLOW YOUR CABINET TO RUN FOR 2 HOURS AFTER
INSTALLATION BEFORE LOADING PRODUCTS INTO THE
REFRIGERATOR.
ALWAYS LOAD YOUR REFRIGERATOR IN BATCHES, FULLY
LOADING YOUR CABINET WITH WARM PRODUCT WILL
INCREASE THE CABINET TEMPERATURE AND MAY CAUSE
LOSS OF PRODUCT.
WHEN LOADING YOUR REFRIGERATOR ALWAYS ALLOW
ADEQUATE SPACE FOR FLOW OF AIR INSIDE THE CABINET.
NEVER LOAD PRODUCTS TOUCHING THE INTERIOR WALLS
OF THE UNIT. NEVER LOAD PRODUCTS SO THAT THEY ARE
OVERHANGING THE SHELVES. THE SPACE BETWEEN THE
FRONT OF THE SHELF AND THE DOOR IS DESIGNED TO
ASSIST AIR FLOW, NEVER BLOCK THIS SPACE.
ALWAYS LOAD YOUR REFRIGERATOR WITH CARE, NEVER
THROW OR DROP ITEMS ON TO THE SHELVES AS THIS
COULD CAUSE DAMAGE TO THE INSIDE OF THE CABINET OR
DISLOCATE THE SHELF CAUSING DAMAGE OR INJURY.

OPERATING THE INTERIOR LIGHTS

THE INTERIOR LIGHTING CAN BE SWITCHED OFF AT
NIGHT OR WHEN THE CABINET IS NOT IN USE TO SAVE
ELECTRICITY AND REDUCE RUNNING COSTS.
OPERATING THE LIGHT (COOLERS FITTED WITH ELITECH
ECS-16 CONTROLLER)
YOUR CABINET FEATURES A DIGITAL
TEMPERATURE CONTROLLER WHICH ALSO CONTROLS
THE LIGHTS. TO TURN THE LIGHTING ON AND OFF SIMPLY
PRESS THE BUTTON WITH THE LIGHT BULB ICON.
OPERATING THE LIGHT (COOLERS FITTED WITH SF-101
CONTROLLER)
YOUR CABINET FEATURES A DIGITAL
TEMPERATURE CONTROLLER WHICH ALSO CONTROLS
THE LIGHTS. TO TURN THE LIGHTING ON AND OFF SIMPLY
PRESS THE BUTTON WITH THE LIGHT BULB ICON.

EFFICIENT USE

TO PREVENT COLD AIR FROM ESCAPING OPEN AND CLOSE
THE DOOR QUICKLY.
ALWAYS LOAD YOUR CABINET TO ALLOW FOR SUFFICIENT
AIRFLOW BETWEEN PRODUCTS.
ALWAYS TRY TO KEEP YOUR CABINET AS FULLY LOADED
WITH COLD PRODUCE AS POSSIBLE.
INSTALL THE UNIT IN A WELL VENTILATED AREA WHERE THE
AMBIENT TEMPERATURE WILL NOT RISE ABOVE 30°C.
NT100818UM Rev 1.1
THE CABINET IS SUITABLE FOR USE IN CONDITIONS UP TO
55% RELATIVE HUMIDITY. CONDITIONS ABOVE THE RATED
VALUE WILL CAUSE EXCESS FROST AND ICE BUILD UP
WHICH WILL AFFECT THE PERFORMANCE AND EFFICIENCY
OR THE REFRIGERATION SYSTEM
DEFROST YOUR CABINET REGULARLY TO KEEP ICE BUILD UP
AND FROST TO A MINIMUM TO INCREASE EFFICIENCY
EFFICIENT USE
TO PREVENT COLD AIR FROM ESCAPING OPEN AND CLOSE
THE DOOR QUICKLY.
ALWAYS LOAD YOUR CABINET TO ALLOW FOR SUFFICIENT
AIRFLOW BETWEEN PRODUCTS.
ALWAYS TRY TO KEEP YOUR CABINET AS FULLY LOADED
WITH COLD PRODUCE AS POSSIBLE.
INSTALL THE UNIT IS A WELL VENTILATED AREA WHERE THE
AMBIENT TEMPERATURE WILL NOT RISE ABOVE 30°C.
THE CABINET IS SUITABLE FOR USE IN CONDITIONS UP TO
55% RELATIVE HUMIDITY. CONDITIONS ABOVE THE RATED
VALUE WILL CAUSE EXCESS FROST AND ICE BUILD UP
WHICH WILL AFFECT THE PERFORMANCE AND EFFICIENCY
OR THE REFRIGERATION SYSTEM
DEFROST YOUR CABINET REGULARLY TO KEEP ICE BUILD UP
AND FROST TO A MINIMUM TO INCREASE EFFICIENCY

EXTERIOR CLEANING

ALWAYS CLEAN THE EXTERIOR OF THE REFRIGERATOR WITH
A MICRO-FIBRE CLOTH AND OR A SPONGE.
DO NOT USE ABRASIVE OR METALLIC PRODUCTS (WIRE
WOOL) WHICH COULD SCRATCH AND DAMAGE THE FINISH
OF THE REFRIGERATOR PERMANENTLY.
GLASS CLEANING
CLEAN THE GLASS DOORS OF THE FRIDGE WITH GLASS
CLEANING CHEMICALS AND WIPE DRY WITH PAPER TOWELS
TO AVOID SMEARS.
INTERIOR CLEANING
CLEAN THE INTERIOR OF THE REFRIGERATOR AND ALL
REMOVABLE PARTS BY WASHING THEM WITH A SOLUTION
OF LUKEWARM WATER AND A SMALL AMOUNT OF DISH-
WASHING LIQUID. RINSE AND DRY IMMEDIATELY.
WARNING
ALTHOUGH THE REFRIGERATOR HAS BEEN TESTED AND
CLEANED AT THE FACTORY DIRT AND PARTICLES MAY OF
ENTERED THE CABINET DURING TRANSIT, UNPACKING
AND INSTALLATION. DUE TO THIS IT IS IMPORTANT THAT
YOUR REFRIGERATOR IS CLEANED INSIDE AND OUT
BEFORE OPERATION.
4
PART IV