Operating Instructions; Altering The Temperature; Defrosting; Adjusting The Shelves - PRODIS NT Series User Manual

PART III
WARNING
IF THE POWER SUPPLY CABLE IS DAMAGED, DO NOT
INSTALL OR OPERATE THE MACHINE UNTIL THE CABLE
HAS BEEN REPLACED BY AN AUTHORISED SERVICE
PARTNER OR A QUALIFIED ENGINEER.
WARNING
ALL ELECTRICAL CONNECTIONS MUST CONFORM
TO LOCAL REGULATIONS AND BE CARRIED OUT BY A
QUALIFIED ENGINEER

OPERATING INSTRUCTIONS

WARNING
AFTER TURNING OFF YOUR REFRIGERATOR YOU MUST
WAIT AT LEAST 5 MINUTES BEFORE RESTARTING TO
AVOID DAMAGE TO THE COMPRESSOR
ALTERING THE TEMPERATURE (COOLERS FITTED WITH AN
SF-101 CONTROLLER)
SET
SF-101
YOUR COOLER FEATURES A DIGITAL CONTROLLER. ALL
PARAMETERS ARE PRESET AT THE FACTORY FOR OPTIMUM
COOLING PERFORMANCE AND EFFICIENCY. ALTERING
THE PARAMETERS OF THE DIGITAL CONTROLLER WILL
ADVERSELY AFFECT THE COOLING EFFICIENCY AND
PERFORMANCE OF THE COOLER.
TO CHANGE THE SET POINT OF YOUR COOLER PRESS AND
HOLD THE SET BUTTON, THE DISPLAY WILL FLASH AND THE
CURRENT SET TEMPERATURE WILL BE DISPLAYED. USE THE
UP AND DOWN ARROWS TO ADJUST THE TEMPERATURE
ACCORDING TO YOUR NEEDS AND PRESS THE SET BUTTON
AGAIN TO STORE THE NEW SET POINT.
CHANGING THE SET POINT WILL AFFECT THE
PERFORMANCE AND EFFICIENCY OF THE COOLER
AND SHOULD ONLY BE UNDERTAKEN BY A QUALIFIED
REFRIGERATION ENGINEER.
ALTERING THE TEMPERATURE (COOLERS WITH ELITECH
ECS-16 DIGITAL TEMPERATURE CONTROL)
refulgence
2.2
YOUR COOLER FEATURES A DIGITAL CONTROLLER. ALL
PARAMETERS ARE PRESET AT THE FACTORY FOR OPTIMUM
COOLING PERFORMANCE AND EFFICIENCY. ALTERING
THE PARAMETERS OF THE DIGITAL CONTROLLER WILL
ADVERSELY AFFECT THE COOLING EFFICIENCY AND
PERFORMANCE OF THE COOLER.
TO CHANGE THE SET POINT OF YOUR COOLER PRESS THE
SET BUTTON FOR 3 SECONDS UNTIL ST IS DISPLAYED IN
THE DISPLAY. WITH ST SHOWING IN THE DISPLAY PRESS
THE SET KEY AGAIN, THE CURRENT SET POINT IS NOW
DISPLAYED ON THE CONTROLLER. TO ADJUST THE SET
POINT USE THE UP AND DOWN ARROWS TO SELECT THE
NEW TEMPERATURE AND THEN PRESS SET ONCE AGAIN TO
STORE THE NEW VALUE.
CHANGING THE SET POINT WILL AFFECT THE
PERFORMANCE AND EFFICIENCY OF THE REFRIGERATOR
AND SHOULD ONLY BE UNDERTAKEN BY A QUALIFIED
REFRIGERATION ENGINEER.

ADJUSTING THE SHELVES

YOUR COOLER IS FITTED WITH ADJUSTABLE SHELVES
WHICH CAN BE MOVED TO SUIT DIFFERENT SIZE
PRODUCTS. TO ADJUST THE SHELVES REMOVE THE SHELF
COMPLETELY FROM THE UNIT TO REVEAL THE SHELF CLIPS.
LIFT THE SHELF CLIPS UPWARDS TO REMOVE THEM FROM
THE SUPPORT LADDER.
TO REINSTALL THE SHELF INTO THE CORRECT LOCATION
REPLACE THE CLIP INTO THE SUPPORT LADDER ENSURING
ALL CLIPS ARE AT THE SAME LEVEL AND REPLACE THE
SHELF

DEFROSTING

THIS REFRIGERATOR IS FITTED WITH AN AUTOMATIC
DEFROST SYSTEM. MANUALLY DEFROSTING IS NOT
REQUIRED UNDER NORMAL CIRCUMSTANCES.
IN HUMID CONDITIONS MOISTURE IN THE AIR MAY CAUSE
AN EXCESS BUILD UP ON FROST ON THE INSIDE OF THE
UNIT.
TO DEFROST YOUR COOLER UNLOAD THE CABINET AND
TURN OFF UNTIL ALL FROST AND ICE BUILD UP HAS
NATURALLY MELTED. A TOWEL MAY NEED TO BE PLACED
UNDER THE CABINET TO SOAK UP ANY EXCESS MOISTURE
GENERATED DURING DEFROST. IF FROST BUILD UP
REOCCURS AND THE CABINET IS WITHIN ITS NORMAL
AMBIENT OPERATING TEMPERATURE THE THERMOSTAT
MAY BE SET TOO LOW, ADJUST THE SET POINT TO THE
FACTORY DEFAULT SETTING OF 2°c.
WARNING
NEVER REMOVE FROST OR ICE BUILD UP WITH A
SHARP IMPLEMENT OR TOOL AS THIS WILL DAMAGE
THE REFRIGERATION SYSTEM AND WILL VOID YOUR
WARRANTY
WARNING
NEVER TOUCH THE EVAPORATOR SURFACE WHEN THE
MACHINE IS RUNNING AS THIS MAY CAUSE INJURY TO
THE USER
3 NT100818UM Rev 1.1