Related Manuals for Haas+Sohn HSDZ 75.5-SF easy
Summary of Contents for Haas+Sohn HSDZ 75.5-SF easy
- Page 1 SOLID FUEL STOVE HSDZ 75.5-SF easy Type HKS 1575 –SF AL HSDZ 75.5 easy Type HKS 1575-AL Operating and installation manual...
-
Page 2: Table Of Contents
Dear Customer! Congratulations and thank you for choosing Haas+Sohn solid fuel stove; hope that it will please you for many many years. You bought a solid fuel stove equipped with an innovative heating system, which burns the prescribed fuel in an environment friendly and economical way. -
Page 3: General
General information Dear Customer! Before starting up please read these instructions carefully. Then you get familiar with operating the stove very quickly. A solid fuel stove is not a toy... The stove is hot during operation! Therefore children should be implicitly kept away, as they do not recognize the risks which can occur when handling stoves. -
Page 4: Safety Notice
Safety instructions The stove must be installed by a qualified personnel. Important information on this subject can be found in chapter ‘Installation instructions’. Before connecting the stove, please call a chimney sweeper to check the chimney. Heat the oven only with closed door. ... -
Page 5: Technical Specifications
Dimensions and connecting dimension A two-part base offers the possibility of height adjustment (max. 30 mm). For this remove the fixing screws and fix the lower panel at the desired height. Technical specifications Dimensions HSDZ 75 .5 850*/750/600 Apparatus *(without cover) H/W/D mm 270/330/410 Oven... -
Page 6: Installation Instructions
Installation instructions When installing the stove, all legal and relevant fire safety regulations must be observed. If the stove is installed on a flammable material like for example wood, then a bottom plate has to be attached which overlaps the device minimum 10 cm laterally and minimum 50 cm forward. -
Page 7: Connection To The Chimney
Installing with upper flue outlet 1.) Remove the inlaid cover from the hotplate. 2.) Attach the flue outlet from the bottom and fasten it with the enclosed screws and washers. ATTENTION – The stove frame must be installed flush-mounted! Connection to the chimney ... -
Page 8: Connection For The External Combustion Air Supply
Connection to external combustion air supply is only valid for HSDZ 75.5 - AL Connection to external combustion air is available for these stove models. (DIN EN 12815 certificated). The stove operates basically with open flue thus enough amount of fresh air has to be guaranteed in the operation room. - Page 9 When using a home ventilation system including a fireplace, it’s obligatory to consult your responsible chimney sweeper! For the fresh air supply connection on the stove, use a designated insulated flexible pipe with a diameter of 60mm. If using rectangular tubes, the appropriate cross section must be observed.
-
Page 10: Controls
Controls Air regulation Knob position Start - heating up: In this position all ventilation openings are fully open. In addition, the exhaust flap (oven side) opens to reduce the flue gas. This ensures a better air draught during heating up. Knob position wood - heating mode: As soon as the fuel vividly burns (depending on the air draught conditions), the knob must be adjusted to... -
Page 11: Height Adjustment
Air draught regulator Knob position 30%: With the air draught regulator the increased chimney air draught can be throttled. (for example too high chimney or weather conditions). The air draught regulator must not be shuttered in the heating phase, so that the fuel can burn optimally. Knob position 100%: This position is selected in the heating-up phase, as well as the necessary delivery pressure of the... -
Page 12: Cleaning Cover
Cleaning cover The air system under the oven can be cleaned via the cleaning cover. Remove the enamelled cleaning panel with a strong pull. Open the cleaning cover by unscrewing the wing nuts and place it carefully (Attention: Do not break the sensors and sensor wires.) ... -
Page 13: Oven
Oven Remove all accessories from the oven and clean them with warm water and standard detergent. Do not use abrasive cleaners! Remove the oven door Completely open the oven door. Fold forward the safety clips on the hinges (open). ... -
Page 14: Starting Up
Starting up Please perform the following steps when using the device for the first time: Remove all accessories from the ashpan and oven. Rub dry the enamelled surfaces. Light a small fire so the fire bricks can dry slowly. A slight smoke may come from the stove besides the typical ‘new door‘ during this phase. -
Page 15: Heating
Heating Heating with wood Dust emission limitation By proper use dust emission can be greatly Firewood may be burned only air-dried. avoided. Factors affecting the dust and soot For heating adjust the air regulation to by the VDI guideline 2118 are set forth in the "wood". -
Page 16: Cooking
Fruit juices dripping from the baking tray may leave stain on the enamel Cooking that can not be removed later. Always prehat the oven for baking Dishes and frying. The pots used should have a massive and ... -
Page 17: Cleaning And Maintenance
The exhaust pipe has to be removed Cleaning and and cleaned outside. Clean the maintenance connection opening thoroughly before taking it back. Sweep deposits from the oven top Proceed as per the below when cleaning: under the oven via the side air stack ... -
Page 18: Glass Ceramic Stove Top
Glass ceramic stove Caramelised sugar Molten plastic must removed immediately (while still hot) with a glass Safety priority during scraper. Clean the area afterwards as production and construction described in point 2. The ceramic hob is mechanically very When using and moving pots with stable and can withstand readily moderate aluminium bottom there can be some to heavy shocks. -
Page 19: Implementation, Cleaning And Maintenance Of The Stove Top Faults, Failure Analysis
Failures, failures Failures and failures: Workaround: Heat the oven for several hours. Unpleasant smell, withering of the protective coating Not effective heating of the oven a.) The delivery pressure should be ca. 12 Pascal. Inspect the thickness of a) Too low delivery pressure chimney. -
Page 20: The Chimney
Failures and failures: Workaround: 6. Exhaust gases exit: a.) Contact chimney sweeper .) The delivery pressure is too weak b.) External air supply b.) Structural conditions such as for example (too) tight windows and doors, such as exhaust gas emission when opening oven door c.) Ensure adequate air supply c.) Stove hood is switched on... -
Page 22: Notes
Notes:... - Page 24 Warranty: Haas+ Sohn provides guarantee to the buyer within the statuory regulations. The warranty period commences on the actual date of the delivery to the customer. In proof the bill is to be submitted. For inquiries, ordering spare parts or complaints please share the model number and the manufacturing number of your stove.