Download Print this page
Gehl 600 Series Dealer Setup Instructions
Gehl 600 Series Dealer Setup Instructions

Gehl 600 Series Dealer Setup Instructions

Finger wheel rakes

Advertisement

Quick Links

These instructions provide details for unpacking and
setting up the 600 Series Finger Wheel Rakes. This
document should remain with the machine in the
manual packet. A copy of this document should be
retained by the dealer.
GENERAL INFORMATION
The 600 Series Finger Wheel Rakes are shipped in
varying stages of assembly. The following instructions
provide illustrated details of how to set up the 600 Series
Finger Wheel Rakes. Recommended setup is as follows:
Unless otherwise noted, the standard fastening
procedure is to secure two parts with a cap screw and
lock nut. A part with a mounting slot should be secured
with a plain washer against the slotted surfaces. Lock
nuts are sometimes used to prevent two parts from
separating but still allow one part to move or rotate next
to the other. Attaching hardware, if it will require
installation in the path of material flow, should always
be installed with the head of the screw on the same side
of the part that will be in contact with the material.
Printed in U.S.A.
Dealer Set-up
Instructions for
the 600 Series
Finger Wheel Rakes
SETUP
1.
Implement is shipped disassembled in wooden
crates. Approximate assembly time is between
15-25 hours, depending on what options are to be
installed. The majority of the fasteners are metric.
IMPORTANT:
fasteners.
2.
Select an area that has adequate space for parts
layout and machine assembly. Remove all parts
from the crate and lay them out in assembly order
according to Fig. 2.
1
Fig. 1
Use only metric tools for metric
918203/AP0305

Advertisement

loading
Need help?

Need help?

Do you have a question about the 600 Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Gehl 600 Series

  • Page 1 The 600 Series Finger Wheel Rakes are shipped in varying stages of assembly. The following instructions provide illustrated details of how to set up the 600 Series Finger Wheel Rakes. Recommended setup is as follows: Unless otherwise noted, the standard fastening procedure is to secure two parts with a cap screw and lock nut.
  • Page 2 15, Fig. 8 2, Fig. 8 11, 12, Fig. 14 1, Fig. 9 1, Fig. 9 6, Fig. 10 6, Fig. 10 22, Fig. 6 2, Fig. 6 6RH, Fig. 10 6LH, Fig. 10 10, Fig. 12 10, Fig. 12 6, Fig.
  • Page 3 REAR FRAME ASSEMBLY (Fig. 3) Assemble the rear member (1) with the key stock facing forward to the right hand wheel support (2) and the left hand wheel support (3) using the M14 x 40 bolts (6) and the M14 nuts (7) as shown. Install the two supports (4) as shown using the M14 x 40 bolts (6) and the M14 nuts (7).
  • Page 4 SINGLE AXLE FOR REAR FRAME (Fig. 4) Apply grease to spindle (1) and slide into rear frame (2). Secure with M10 x 90 cap screw (3) and M10 locknut (4). Attach ground wheel (5) to hub (1) with M16 conical lug nuts (6). Repeat steps 1 and 2 on opposite side of rear frame.
  • Page 5 TANDEM AXLE FOR REAR FRAME (Fig. 5) Insert spring pin (1) through bushing (2) and pivot shaft (3). Slide support hub (4) onto pivot shaft (3) with flange next to bushing (2). Apply grease to pivot shaft (3) and slide into rear frame (5). Secure with M10 x 90 cap screw (6) and M10 lock nut (7).
  • Page 6 WING FRAME ASSEMBLY (Fig. 6) Using stands (19) that are 30” (762 mm) high, support the frames and connect the rear frame (1), the front frame (2) and secure using the M14 x 40 bolts (4) and the M14 lock nuts (5). NOTE: If an optional extension frame, flex frame, center splitter wheel or extra wheel kit is to be installed, please see the options sections (Figs.
  • Page 7 WINDROW ADJUSTMENT ASSEMBLY (Fig. 7) Thread the acme screw (7) half-way into the sliding rail (1) with the hole in the acme screw (7) facing towards the outside of the machine as shown. Attach the sliding rail (1) to the wing frame as shown. Secure in place by inserting the sliding rod (8).
  • Page 8 DRAWBAR ASSEMBLY (Fig. 8) Install the rear drawbar (1) to the rear member with the plate (4) using eight M14 x 160 cap screws (5) and eight M14 lock nuts (6). Assemble the nylon plates (9) on the sliding drawbar (2) using the eight M8 x 20 cap screws (10).
  • Page 9 CASTER WHEEL ASSEMBLY (Fig. 9) Assemble the wheel with hub (6) into the wheel fork (1) using the wheel fork pivot (9), short spacer (7), long spacer (8) and lock nut (10) as shown. Slide the shaft of the wheel fork assembly (1) up into the wheel support and install the brake plates (5) onto the brake disk (3) and secure them in place using the spring pin (4).
  • Page 10 OPENING ARM ASSEMBLY (Fig. 10) Insert the nylon plates (14, 15) inside the slide (1) in the slots properly, long nylon plates on the top and bottom and the short plates on the sides. Mount the slide (1) on the rear drawbar and attach the cover (2) using the ten M10 x 30 cap screws (11).
  • Page 11 HYDRAULIC OPENING-CLOSING SYSTEM ASSEMBLY (Fig. 11) Insert the hydraulic cylinder (2) on to the rear drawbar and secure it with the pin (14) and the cotter pins (15) as shown. Install the fittings (8) on to the ports of the cylinder (2). Pass the 354” (8992 mm) hoses (1) through the brackets on the sides of the rear drawbar and then through the hose chain (3) and attach the hose chain (3) with the M8 x 25 cap screws (12) and the lock nut (13).
  • Page 12 HYDRAULIC LIFT ARM ASSEMBLY (Fig. 12) Install the fittings (3) on the cylinder (10) directing them towards the front of the rake. Mount the cylinder (10) on the wing frame as shown. Fasten the cylinder (10) to the frame using the pins (9) and “omega” circlips (16). Fasten the hoses (2) to the fittings (3) on the cylinder and then to the frame using the double hose clamp (13), plate (15) and the M8 x 25 screw (14).
  • Page 13 RAKE WHEEL ASSEMBLY (Fig. 13) Assemble the nylon bushings (5) onto the tubes welded on the underneath side of the wing frames. Slide in the arms carrying the rake wheels (4) through the nylon bushings and secure them with a washer (6) and a cotter pin (7).
  • Page 14 TRANSPORT BAR (Fig. 14) Assemble the transport safety bar wing frame mounting brackets (3, 4) onto the wing frames with two M14 x 160 cap screws (5) and two M14 hex nuts (6). Attach the transport bar plate (1) to the end of the wing frames using three M14 x 50 cap screws (8).
  • Page 15 OPTIONAL 2-WHEEL EXTENSION (Fig. 15) Install the extension frames (32, 33) on the front of the wing frames using six M14 x 40 cap screws (30) and six M14 nuts (31). Mount the decal plate on the back of the furthest forward left wing frame mount similar to Fig.
  • Page 16 OPTIONAL 4-WHEEL EXTENSION (Fig. 16) Install the extension frames (32, 33) on the front of the wing frames using six M14 x 40 cap screws (30) and six M14 nuts (31). Mount the decal plate on the back of the furthest forward left wing frame mount similar to Fig.
  • Page 17 OPTIONAL FLEX FRAME (Fig. 17) Install the flex frame brackets (35) on the front of the wing frames using six M14 x 40 cap screws (30) and six M14 nuts (31). Slide the flex frame beams (32, 33) into the flex frame brackets (35) and insert pins (36) through the brackets and flex frame beams as shown.
  • Page 18 OPTIONAL 5TH & 6TH GROUND WHEELS (Fig. 18) Install grease zerks (2) into wheel supports (11,12). Attach the wheel supports (11,12) to the wing frames using six M14 x 40 cap screws (13) and six M14 lock nuts (14) on each side. Assemble the wheel with hub (6) into the wheel fork (1) using the wheel fork pivot (9), short spacer (7), long spacer (8) and lock nut (10) as shown.
  • Page 19 OPTIONAL CENTER SPLITTER WHEEL ASSEMBLY (Fig. 19) Install the support (1) on the front drawbar with the u-bolts (16) and the nuts (22). Mount the pivoting supports (2, 3) and secure them using the rings (14), the M10 x 100 cap screws (18) and M10 nuts (19). Connect the pivot- ing supports to the opening arms with the connection bars (4, 5), the M20 x 90 cap screws (17) and the M20 nuts (20).
  • Page 20 cont. OPTIONAL CENTER SPLITTER WHEEL ASSEMBLY (Fig. 20) Install the straight fitting (1), copper ring (14) and the lock valve (15) to the upper port on the hydraulic cylinder. Attach one elbow (3) to lower port and one elbow (3) to lock valve (15) on the hydraulic cylinder. Remove the caps from the tee fittings on the drawbar and connect the hoses (2) to the tee fittings and to the cylinder as shown.
  • Page 21 Ref. Part Qty. Ref. Part Qty. Description Req. Description Req. 170323 FAST FLUID CONNECTOR 1/2” ..170066 VALVE FOR CYLINDER 3/8 ... 170329 WASHER + OR 1/2”...
  • Page 22 NOTES 918203/AP0305 Printed in U.S.A.
  • Page 23 NOTES Printed in U.S.A. 918203/AP0305...
  • Page 24  Gehl Company 143 Water Street, P.O. Box 179, West Bend, WI 53095-0179 U.S.A. www.gehl.com 2005 GEHL Company, All rights reserved. 918203/AP0305 918203/AP0305 Printed in U.S.A. Printed in U.S.A.