Page 1
LANGUAGE : ENGLISH SLIDING TABLE SAW FF-325 PLUS !!! For your safety !!! Read the manual instructions. Http://www.inmes.com.br 05040784...
Page 3
Dear customer, Thank you so much for allowing us to share the experience of using an Inmes product. The following manual has been formulated by our technical team especially for you to guide you in using this equipment safely and productively.
Follow the instructions in this manual for the correct use of your equipment. Only trained and authorized personnel should use and service the machine after reading the instruction manual. Respect accident prevention regulations, general safety rules as well as industrial medicine rules. INMES Industrial Ltda – Sliding table saw FF-325 Plus...
- Any transportation, assembly or disassembly must be done by trained personnel who have been qualified for the specified operation. -The operator should not leave the machine at any time without turning it off. INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Risk of injury to eyes. Wear safety goggles. Use ear protectors. Danger of electric shock. Do not access this area with the machine turned on. Read and understand the instruction manual before using the machine. INMES Industrial Ltda – Sliding table saw FF-325 Plus...
220V machine a 25A circuit breaker is recommended. To prevent electric shock or fire, any maintenance or repair to the electrical system should only be done by trained electricians using genuine parts of the machine. INMES Industrial Ltda – Sliding table saw FF-325 Plus...
3.5 Dust collector (Pic. 3.5) Always work with the exhaust system, turning on the hood and the saw machine at the same time. Dust pickup Item Ø Outfall Speed 4” 20m/s 4” 20m/s (Pic. 3.5) INMES Industrial Ltda – Sliding table saw FF-325 Plus...
When the button is pressed the power will be completely cut off from the machine immediately, this is a mechanically pressed emergency button, to turn it off simply by turning the knob clockwise. (Pic. 3.6) INMES Industrial Ltda – Sliding table saw FF-325 Plus...
- Remove all protective grease from unpainted tables and surfaces using kerosene or by-products. Do not use solvents, petroleum or gas oil, which may damage the paint or rust parts of the machine. (Pic. 4.2) INMES Industrial Ltda – Sliding table saw FF-325 Plus...
These parts should be installed as follows. Tighten all bolts and nuts tightly. If this is not done correctly, there is a risk that the machine will trip or cause danger to the operator or another person. INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Place the transverse table C into the car seat A. - Insert pin D into the cross table bracket C and the carriage bracket table bracket E - Fix the planks using knobs B. (Pic. 4.4.3) INMES Industrial Ltda – Sliding table saw FF-325 Plus...
4.4.6 Ruler Installation (Pic. 4.4.6) - Install the ruler bracket A to guide B as shown. - Install screw C to ruler guide B. - Install ruler D to bracket fitting A. (Pic. 4.4.6) INMES Industrial Ltda – Sliding table saw FF-325 Plus...
(Pic. 5.2) - Loosen nut C using 13mm wrench and adjust table by turning screw D using 4mm Allen wrench. - Retighten all screws A. - Retighten all C nuts. INMES Industrial Ltda – Sliding table saw FF-325 Plus...
- And it is the emergency button which turns off all power to the machine. - F is the display indicating the angle of inclination the saw is currently in. (Pic. 6.1) INMES Industrial Ltda – Sliding table saw FF-325 Plus...
- Place the piece to be cut on the extension table. aluminum stop B - Stay in position A and push the extension table forward to make the cut. (Pic. 6.3.1) INMES Industrial Ltda – Sliding table saw FF-325 Plus...
-Do not let the piece stop between the blade and the ruler. - Avoid contact of the saw teeth with metallic objects. - Whenever necessary sharpen the blade. (Pic. 6.4) INMES Industrial Ltda – Sliding table saw FF-325 Plus...
- Use compressed air only when necessary, wearing goggles and mask. Clean mainly the following parts: - Extender table guide A; - Cross table support B; (Pic. 7.2) INMES Industrial Ltda – Sliding table saw FF-325 Plus...
In the event of mechanical or functional defects in the machine, including guards or tools, contact your service representative for service. Any maintenance should be done only when the machine is disconnected from any power source. INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Page 24
For any problem or information or abnormality in the mountains, contact your local distributor or our service center. INMES INDUSTRIAL LTDA After Sales Service at SAC (48) 3651-2300 or 0300 788 2022. INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Page 25
Saw lifting mechanism too tight. Adjust the mechanism and its shaft. Blade has no free height Dust and wood chips on the saw lift and tilt adjustment. Clean and grease the settings. mechanism. INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Page 35
LIMIT SWITCH FF-325 PLUS 04080011 HEX BOLT INT W/ HEAD M4X30MM DIN 912 04080089 HEX BOLT INT W/ HEAD M6X10MM DIN 912 P02012972 OUTLET 4INCH EXHAUST HOSE FF-325 PLUS P02013162 SPACER PLATE FF-325 PLUS INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Page 37
TUBE STOP SHAFT SUPPORT FF-325 PLUS P02012982 SHAFT SUPPORT TUBE 04080069 HEX NUT MA 10MM ZINC P02012983 PLATE KNOB TILT REGULATOR BLADE AND RISKER FF-325 PLUS P02012984 BLADE AND RISKER HEIGHT REGULATOR KNOB FF-325 PLUS 04080219 FLAT WASHER 3/8 INCH STEEL ZINC P02012985...
Page 39
HEX BOLT INT W/ FLAT HEAD M6X16MM DIN 7991 P02013002 RISKER MOTOR SUPPORT SHAFT FF-325 PLUS 04080492 LOCK WASHER 8MM STEEL ZINC 04080026 HEX BOLT INT W/ HEAD M8X20MM DIN 912 INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Page 41
04080143 HEX BOLT INT W/ HEAD M5X10MM DIN 912 04080253 HEX BOLT INT W/ HEAD M6X12MM P02013020 EXTENDING TABLE 800X820MM FF-325 PLUS 04080059 HEX BOLT INT W/OUT HEAD M8X10MM DIN 916 INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Page 42
PARAF DE AJUSTE BATENTE MESA FIXA FF-325 PLUS P02013233 TABLE SPACER SAW/RISKER FF-325 PLUS 04080676 HEX BOLT INT W/ FLAT HEAD M5X25MM DIN 7991 04080092 HEX BOLT INT W/ FLAT HEAD M5X16MM DIN 7991 INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Page 48
AUXILIARY ARM TIP FF-325 PLUS 04080089 HEX BOLT INT W/ HEAD M6X10MM DIN 912 P02013048 CROSS TABLE AUXILIARY ARM SUPOORT FF-325 PLUS P02013049 CROSS TABLE FASTENING PIN FF-325 PLUS 04080494 HEX NUT MA 20X1,5MM ZINC INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Page 54
ELASTIC RING FOR AXLE RETENTION D8,00 P02013089 SMALLER JOINT PLATE FF-325 PLUS 04080201 FLAT WASHER 5/16 INCH STEEL ZINC 04080177 HEX NUT MA 6MM ZINC DIN 934 P02013090 SMALLER ARTICULATION PLATE TUBE FF-325 PLUS INMES Industrial Ltda – Sliding table saw FF-325 Plus...
Page 62
C N P J : . 9 5 8 5 2 5 4 7 0 0 0 1 2 1 h t t p : / / w w w. i n m e s . c o m . b r e-mail: vendas@inmes.com.br S A C 0 3 0 0 7 8 8 2 0 2 2...