Related Manuals for Rime Lite F Series
Summary of Contents for Rime Lite F Series
- Page 1 USER GUIDE F2 / 4 / 6 Please read this manual before operating F, and keep it for future reference.
- Page 2 Index Introduction Intellectual Property Safety Introduction Unpacking Layout Specification Operation Instruction for MIRA Operation Instruction for SWING Check list when troubling Replacing lamp and flash tube Accessories Warranty...
-
Page 3: Intellectual Property
All intellectual property, owned by or which is otherwise the property of Rime Lite or its respective suppliers relating to F-Flash, including but not limited to, accessories, parts, or software, is proprietary to Rime Lite. No title to or ownership in the intellectual property is transferred to you. All applicable rights... -
Page 4: Safety Instructions
When placing a lamp into the holder ensure not to touch the bulb with bare hands. Equipment must only be serviced, modified or repaired by authorized and competent service personnel. Please be aware that Rime Lite claims no responsibility for damage from data loss due to breakdown, repair, or other causes. - Page 5 Unpacking Your package contains the following items. Power Cable Synchro Cable Halogen Lamp F-flash You can obtain the following accessories for from your local dealer: MIRA SWING III- Transmitter SWING III- Receiver...
- Page 6 Layout Cursor Description Cursor Description ① Protecting Glass ⑨ PhotoCell ② Modeling Lamp ⑩ Main Inlet ③ Flash Tube ⑪ Modeling Lamp Fuse ④ Modeling Base ⑫ Synchro Socket ⑤ Umbrella Holder ⑬ Receiver Holder ⑥ Locking Holder ⑭ Power Button ⑦...
-
Page 7: Specification
SPECIFICATION... -
Page 8: Control Panel
Operation Instruction for MIRA A. Insert a power cord into the main Inlet. B. Turn the power switch ON C. Before switching off, better to set all buttons & indicators to “Minimum” or “OFF” Control Panel, Main Display Control panel Modeling lamp / 0.5f-step/0.1f-stop Flash &... - Page 9 1. Quick flash power & Modeling lamp output control (0.5f-stop increment) Use the Setup button on control panel. Power increment as 0.5 f-stop or 0.1 stop. Easily, enables to identify the power increment setting on the main Display. The power up/down of Flash and modeling increase as 0.5f-stop, If LED on main display is On.
- Page 10 2. Flash power & Modeling Up/Down. , then ‘FLASH’ LED is On Press SELECT button Control panel Power Up/Down button The flash mode menu enables you to control the flash power with Power Up/Down buttons. again, then ‘FLASH’ LED is Off and ‘MODEL’LED is On, Press SELECT button The modeling mode menu enables you to control the Modeling power with Power Up/Down buttons.
- Page 11 3. Proportional Modeling lamp Setup Press Setup button 4. Photocell Press Setup button...
-
Page 12: Ready Beep
5. Ready beep Press Setup button 6. Over Heat Wait until the unit has cooled down. (5 ~10min) The unit will switch back to the normal operation after 5~10min will disappear on the display. -
Page 13: Ready Lamp
7. Ready lamp. The signal on the main display means that the unit is ready to flash. 8. Swing I or III Status. The signal shows that the unit is completed to connect with Swing I or Swing III receiver. - Page 14 Operation Instruction for SWING-I,II,III Before you use SWING-I (Only Triggering) or III (Triggering & Remote control) with F-FLASH, please power off strobes. Transmitter -Join the transmitter to a digital camera Receiver - Join the receiver to a strobe. Notice) when a user set the channel of SWING, the user should adjust the same number of both transmitter and receiver. It can set the maximum 6 strobes per a transmitter under the same channel If a user uses over 6 strobes under the same channel, the effective distance from both a transmitter and a receiver can be shorter.
- Page 15 Check list when troubling 1. Cannot turn on the power. 1) Please check the power switch is On. 2) Please check the power cable inserted correctly. 2. Unit does not flash. 1) Please check the flash tube inserted correctly. 2) Please check the trigger coil contacted with the flash tube legs. 3) Please change the flash tube.
- Page 16 Replacing lamp and flash tube You must switch off and disconnect the power cord before changing lamp or flash tube!!
- Page 17 Accessories...
- Page 18 F-FLASH is free of defects in material and workmanship for a period of twenty four (24) months from the original date of purchase by the consumer.
- Page 19 2. Rime Lite’s sole obligations are to the repair of the defective part, or at its discretion, replacement of the product (service exchange unit) 3.