Advertisement
Quick Links
Advertisement
Related Manuals for Rime Lite Ni-flash
Summary of Contents for Rime Lite Ni-flash
- Page 1 Operating Instructions Ni-flash...
- Page 2 Thank you for choosing a Rimelite product. Please read the operation manual before using Ni-flashes Rimelite’s i Flash is compatible with Canon/Nikon DSLR and mirrorless which have a hot shoe. This equipment’s HSS function can only be used through Swing III Radio Controller & Trigger. .
- Page 3 Nomenclature 1. Flash tube 2. Stand Bracket 3. Replaceable Battery pack 4. Battery release button 5. Strap 6. Sync sensor 7. Main Display 8. Swing III Receiver slot 9. Flash output digital encoder 10. Power On/Off button 11. Function setting buttons 12. Battery indicator-LCD display 13. Battery energy check button...
- Page 4 Power On/Off Press and hold power switch to turn on/off the unit. 1. Normal Mode setting. 1) Rotate the flash digital dial left or right to set the flash output(F-stop)(6). Rotate left to decrease output and right to increase output. Flash output can be decreased/increased by 0.1F-Stop.
- Page 5 3. Multi-flash setting 1) 5 flashes, 10 flashes, 15 flashes / 1second Multi-flash setting is only activated on steps 1.0~1.9 (C.1) and 2.0~2.9 (C.2). Press C/HSS button (A1) on 1.0~1.9(C.1) or 2.0~2.9(C.2) steps. C.1 and C.2 are displayed on the FND display. Pressing the button once fires 5 flashes, pressing it 2 times fires 10 flashes, and pressing it 3 times fires 15 flashes.
- Page 6 4. Modeling light setting(LED 10W, A4) 1) Press ‘LED’ button (A4) to control output of modeling light. Press once to turn off/on modeling light, 2 times for highest output and 3 times for moderate output power. 5. Test button (A-7) 1) Press ‘TEST’...
- Page 7 7. ‘Sound’ setting(A5) ‘Sound’ is displayed. ‘Sound’ function is activated. The flash beeps when it is ready to flash again. SOUND OFF SOUND ON 8. Battery energy check button (3, 8) Press the battery status indicator button (8) to check the remaining battery energy on the LCD display.
- Page 8 2) Press and hold C/HSS button for 2 seconds. Press the button one more time and the letter ‘h’ is displayed. When using HSS under Canon DSLR full-frame body should set Ni-Flash to Capital letter ’H’, Canon DSLR Crop body and all Nikon cameras set Ni-Flash small letter ‘h’...
- Page 9 1. Charge Battery 2. Sync Cable 1) Connect camera SYNC cable to the flash’s SYNC 1) Use only the charger that comes together with the packing. Plug charger into the socket located on the side. charging port located at the side of the battery. AC Pack *AC pack is sold separately 2) When using AC pack...
- Page 10 S-3 User Manual -On/Off separate units (hold 3 Flash test seconds) *Selected unit turns On/Off Adjusting flash output -Select separate unit (short click) To adjust flash output for desired flash, press A-I (1~6) LED beside selected flash button goes red and blinks for 5 seconds *Red Led comes on Press transmitter’s +,- buttons (A-III) to adjust flash output.
- Page 11 This equipment comes built in with a Li-ion battery. Below are instructions on proper battery handling. Characteristics and usage of battery This equipment comes with a 11.1V 4.4A battery. Charge battery with charger that comes with the package before use. One full charge takes approximately 3.5hours, providing up to 400 flashes at maximum output.
- Page 12 Flash should be turned off first before charging the battery. Leaving the flash on while charging lengthens charging time as more power is consumed. Charging time is approximately 3.5 hours with the charger provided together in the package. A battery’s shelf life increases with frequent charging Even if a battery is not fully exhausted, frequent charging increases shelf life and there is no Ni-ca battery memory phenomena. Battery should be charged under around a temperature range of 10°C~40°.
- Page 13 After-sales service policy All Rimelite products are entitled to the following warranty and free after-sales service. All Rimelite products are equipped with flash tubes, capacitors and parts (excluding consumables) that have semi-permanent life cycle without the need for replacement. Apart from certain consumables, all parts are guaranteed a warranty period of 5 years. Paid repair and replacement is possible for the following that renders product exchange and warranty period void: Where product has been damaged through consumer’s misuse and negligence Where product has not been stored in accordance with instructions and product has been disassembled voluntarily...