Installing Your Child Car Seat For Group 0+(Birth-13Kg); Securing Your Child In Car Seat For Group 0+(Birth-13Kg); Installing Your Child Car Seat For Group I(9Kg-18Kg) - MamaLove Infinity User Manual

6.2 Adjusting headrest
6.2.1 . pollex put on the top surface of Headrest adjusting lock (P) then
forefinger dip into the Headrest adjusting button of (O) to push the
headrest up or down, when push to the suitable position, loosen the
forefinger, make small movement of the headrest, the Headrest adjusting
lock(P) will completely fasten into the groove of seat back.
(fig.6)

7. Installing your child car seat for Group 0+(birth-13kg)

7.1 Reclining the seat
7.1.1 Turn the reclining board(M) from back to front. (fig.10)
7.1.2 Grip the red lever(I) at the front of the child car seat and pull the seat
into its fully reclined position. The seat must be fully reclined when facing
rearwards.(fig.11)
Note: Group 0, only suitable for position 4; Group I, suitable for position
1,2,3; the minimum is position 1 &the maximum is position 3;Group II III,
only suitable for position 3.
7.2 Placing the child car seat on passenger seat
Place the child car seat on a passenger seat facing rearward. (fig.12)
7.3 Routing diagonal and lap belts correctly
7.3.1 Put the lap belt under innercushion. (fig.13)
7.3.2 In the meanwhile, bring the diagonal belt through the belt guide(L)
round the back of the seat. (fig.14)
7.4 Tightening the child car seat
7.4.1 Check and make sure there is no twist of the belt. Insert the metal
tongue of carbelt into the carseat buckle until you hear a clear "click". (fig.15)
7.4.2 Tighten the seatbelt by pulling in the direction of the seatbelt reel.
(fig.16)
7.4.3 Pull the lap and diagonal seat belt tightly.
Ensure it's attached as
close as possible to the seatbelt buckle without
touching it. (fig.17)

8 Securing your child in car seat for Group 0+(birth-13kg)

8.1 Loosing the shoulder straps
Press the harness adjust button(H) with one hand, in the meanwhile, pull
the shoulder straps(E) with another hand to loose it. (fig.18)
8.2 Opening the buckle
Hold the two buckle latches with one hand, and another hand holds the
main part of the buckle with thumb pressing the red button until the two
tongues pops out from the buckle.(fig.19)
8.3 Seating your child in the child car seat
Put your child in the seat and put the shoulder pads on the shoulders of the
child.(fig.20)
8.4 Locking the buckle
Guide the two buckle latches together and engage them into the harness
buckle(F).(fig.21)
Warning!
Make sure the two buckle latches are put together correctly and there
is no twist of the harness.
8.5 Tightening the harness straps
Pull the harness adjust strap(J) until the shoulder pads(C) touches the chest
of your child. (fig.22)

9 Installing your child car seat for Group I(9kg-18kg)

9.1 Adjusting the child seat in upright position
9.1.1 Grip the red lever(I) and push the car seat in upright position.(fig.23)
Note: Group 0, only suitable for position 4; Group I, suitable for position
1,2,3; the minimum is position 1 &the maximum is position 3;Group II III,
only suitable for position 3.
9.1.2 Then turn the reclining board from front to back.(fig.24)
9.2 Placing the child car seat on passenger seat
Place the child car seat on passenger seat facing forward.(fig.25)
9.3 Routing diagonal and lap belts correctly
Insert the seatbelt tongue into the slot on backrest and pass it through the
back of the seat.(fig.26)
9.4 Tightening the child car seat
9.4.1 Check and make sure there is no twists of the belt. Plug the car
seatbelt tongue securely into the carseat buckle until you hear a clear
"click". (fig.15)
ENG