Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zte EPON SFU Series
Summary of Contents for Zte EPON SFU Series
- Page 1 ZTE EPON SFU Products 1GE/1GE+CATV User Manual Version：V1.1...
-
Page 2: Table Of Contents
Contents Note ............................1 1.1 Installation Precautions ..................... 1 1.2 Precautions for Use ......................1 Introduce ..........................3 2.1 Product Feature ......................... 3 2.2 Environmental Requirements .................... 4 2.3 Product Interface Definitions .................... 5 2.4 Product LED Definitions ....................5 2.5 Device Connection ...................... - Page 3 ONU Device Management....................21 9.1 ONU Device Remote Access Settings ................21 9.2 Restore Default ....................... 22 9.3 Software Upgrade ......................22 9.4 Reboot Device ......................... 23 Concluding Remarks..............Error! Bookmark not defined.
-
Page 4: Note
1 Note 1.1 Installation Precautions Do not near flammable or conductive items, high temperature, direct sunlight or moist environment, or on PC chassis, and check whether other home equipment placed around stability Check the cable line. Test and confirm the ac or dc input voltage in the range of allowable, and direct current (dc) correct polarity. - Page 5 Power off the device when it not in use. Please make sure the power switch is closed before plug the power supply, to avoid surge. Please be careful when remove the power supply, transformer temperature may be higher. ...
-
Page 6: Introduce
2 Introduce ZTE EPON SFU series of terminal equipment is based on EPON technology based on the broadband access market, to meet the broadcaster operators broadband access and FTTH, and design passive optical network terminal products that integrate CATV optical receiver and achieve broadband, CATV dual network integration. -
Page 7: Environmental Requirements
⚫ Support bidirectional FEC, supports the RS (255, 239) FEC decoding ⚫ Supports default SFU (pure bridged data) access ⚫ Support PPPoE, DHCP, static IP broadband service access ⚫ Support NAT, static routing, port forwarding ⚫ Support data encryption, VLAN transparent, vlan tag, vlan trunk ⚫... -
Page 8: Product Interface Definitions
Operation humidity：10%—90%(Non-condensing) Power adapter input: 12V / 0.5A Transmitted optical power: 0~4dBm Input optical power: -3 ~ -27dBm 2.3 Product Interface Definitions 2.4 Product LED Definitions Indicator Description On: The ONU is power on Power status Off: The ONU is Power off On: Ethernet connection is normal Blinking: Data is being transmitted through LANn... -
Page 9: Device Connection
Off: Failed to register to OLT; On: Optical power lower than receiver GPON optical sensitivity ; signals Off: Optical in normal On：CATV optical normal CATV CATV status Off：The CATV signals are not received 2.5 Device Connection ⚫ Connecting the fiber: Insert the SC fiber connector into the PON connector on the rear panel of the ONU. -
Page 10: Onu And Pc Physical Connection
3.1 ONU and PC physical Connection a) Connect your computer's local network card to the LAN port or ETH port of the ONU via a network cable. b) Set the IP address of the computer's local network card to 192.168.101.X (X: 2-254). c) The computer opens the cmd window. -
Page 11: Onu Registration Information Configuration
adminisp adminisp Enter the ONU super login user: password: Click "Login" button, there will be the following ONU main login interface: After entering the main interface of the ONU, the ONU can be set up further. For details, see the following setup guide. 4 ONU Registration Information Configuration 4.1 ONU Registration Status View web login ONU select the Status ->Network interface ->... -
Page 12: Onu Optical Power Information View
4.2 ONU Optical Power Information View web login ONU select the Status -> Network interface -> PON inform, you can view the ONU input and output optical power information: 4.3 ONU Registration LOID Configuration The LOID of the ONU is mainly applicable to the authentication mode of LOID and LOID + Password. -
Page 13: Internet Basic Configuration
5 Internet Basic Configuration ZTE ONU series of products support route function, Internet can work by route mode or bridge mode, the difference between the two modes are as follows: Routing mode Broadband Internet access: ONU as a home gateway equipment, ONU on route mode can obtained IP address in three ways: DHCP, static IP and PPPoE. -
Page 14: Routing Mode Broadband Internet Settings
ONU LAN port obtained by the OLT upper layer server. The PC is connected to the Internet through DHCP, PPPoE, and static ip address. 5.1 Routing mode broadband Internet settings PPPoE broadband Internet access in routing mode 5.1.1 1. web login ONU and select Network -> WAN -> WAN Connection, and then set the following parameters: 【Connection name】Select "Create WAN Connection". - Page 15 ONU not get the network. Note: ZTE solution ONU series of products is no port binding function, because the ONU is SFU (pure data)+ Routing, the ONU either works in SFU mode, or is working in routing mode.
- Page 16 【Enable NAT】Check the "Enable NAT" function; NAT function is mainly used for internal network and external network communication address translation function, the default is checked enabled state, if not check the network ONU not get the network. Note: ZTE solution ONU series of products is no port binding function, because...
- Page 17 the ONU is SFU (pure data)+ Routing, the ONU either works in SFU mode, or is working in routing mode. 2.After the above configuration, click "create" button to complete the DHCP broadband Internet access settings. Static IP Broadband Internet Access In Routing Mode 5.1.3 1.web login ONU and select Network ->...
- Page 18 DNS, the second DNS and the third DNS for for static ip address Internet access. Note: ZTE solution ONU series of products is no port binding function, because the ONU is SFU (pure data)+ Routing, the ONU either works in SFU mode, or is working in routing mode.
-
Page 19: Broadband Internet Access In Bridge Mode
Internet access settings. 5.2 Broadband Internet Access In Bridge Mode ZTE solution ONU series products factory default mode in the bridge (pure data SFU), ONU bridge mode Internet does not need to do any configuration in the web interface. Just configure the correct ONU port vlan (eg access, trunk, transparent) -
Page 20: Delete Internet Wan Connection
5.4 Delete Internet WAN Connection web login ONU and select the Network -> WAN -> WAN Connection, select a WAN connection in the "Connection Name", and then click the "Delete" button at the bottom of the page to complete the deletion:... -
Page 21: Onu Lan Configuration
6 ONU LAN configuration The LAN side configuration of the ZTE solution ONU is mainly for terminal device when ONU in route mode. 6.1 LAN IP Address Configuration 1.web login ONU and select the Network -> LAN -> DHCP Server, And then set the following parameters: 【LAN IP Address】Set the local management IP address of the ONU. -
Page 22: Multicast / Iptv Service Basic Settings
【DHCP Start IP Address/DHCP End IP Address】The IP address interval allocated to the terminal. The address interval must be on the same network segment as the management IP address of the ONU. 【Assign IspDNS】Enable or Disable the ONU to allocate the upper ISP's DNS to the terminal. -
Page 23: Catv Management
ZTE solution ONU multicast / IPTV service settings are mainly through the OLT to configure, including multicast vlan, snooping configuration can be configured through the OLT. The specific configuration can refer to each manufacturer's OLT to configure. 8 CATV Management CATV management is mainly applied to ONU products with optical machine, you need to configure the optical machine parameters in ONU web. -
Page 24: Onu Device Management
can view the CATV switch status and optical parameters: 9 ONU Device Management 9.1 ONU Device Remote Access Settings web login ONU and select the Security -> Service Control -> Service Control. In this page you can set the ONU telnet remote access and WEB remote access:... -
Page 25: Restore Default
9.2 Restore Default web login ONU and select the Administration -> System Management -> System Management. Click the "Restore Default" button to restore the ONU factory settings: 9.3 Software Upgrade web login ONU and select the Administration -> System Management -> Software Upgrade. -
Page 26: Reboot Device
9.4 Reboot Device web login ONU and select the Administration -> System Management -> System Management. Click the "Reboot" button to restart the ONU device:...