1. Manuals
  2. Brands
  3. Bartscher Manuals
  4. Water Dispenser
  5. WEH1350
  6. Manual

Bartscher WEH1350 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
WEH1350
109889
Original-Gebrauchsanleitung
V2/0217

Advertisement

Table of Contents
loading

Related Manuals for Bartscher WEH1350

Summary of Contents for Bartscher WEH1350

  • Page 1 WEH1350 109889 Original-Gebrauchsanleitung V2/0217...
  • Page 2 ----------------------------------------- DEUTSCH Seite 1 bis 26 ENGLISH ----------------------------------------- from page 27 to 52 ----------------------------------------- FRANÇAIS de page 53 à page 78 ITALIANO ----------------------------------------- pagine da 79 a 104 ESPAŇOL ----------------------------------------- de la página 105 a la 130 PORTUGUÊS ----------------------------------------- as páginas des de 131 até 156 ----------------------------------------- NEDERLANDS blz.

  • Page 3: Table Of Contents

    6.3 Installation of the water softening system ............. 37 6.4 Control panel, indicators, button functions ............39 6.5 Settings ........................ 40 6.6 Service instructions ....................43 7. Possible malfunctions .................... 44 8. Disposal ........................52 Bartscher GmbH Franz-Kleine-Str. 28 D-33154 Salzkotten phone: +49 (0) 5258 971-0 Germany fax:...

  • Page 4: General Instructions

    Read carefully these instruction manual before undertaking any work with the device, in particular before its startup! 1.General instructions  This instruction manual contains information about the installation, operation and maintenance of the device and should be consulted as an important source of information and reference guide.

  • Page 5: Safety Instructions, Standards, Legal And Regulatory Provisions

    2. Safety instructions, standards, legal and regulatory provisions  Water supplying the water softening system must have the drinking water quality and comply with local regulations.  The maximum temperature of the supplied water may not exceed 40 °C.  Components of the water softening system that come into contact with water must be made of appropriate water-resistant material.

  • Page 6: Transport, Packaging And Storage

    4. Transport, packaging and storage 4.1 Delivery check Please check the delivery upon completeness and transport damage immediately after receipt. In case of visible damage do not accept or accept the delivery with reservation only. Note the extent of damage on the carrier’s bill of delivery. Trigger off the complaint. Hidden damages should be reclaimed immediately after notice, as claims for damages can only be asserted within the effective period for complaints.

  • Page 7: Description Of The Device

    In case of longer storage (> 3 months) make sure you check the state of the packaging and the parts regularly. If required refresh or renew. CAUTION! Before the first use of the product in the recommended ambient temperature, after being stored or transported in the temperature below 0° C, leave the device for at least 24 hours in an open original packaging.

  • Page 8: Structure Of The Water Softening System

    5.2 Structure of the water softening system The system was designed for 0.7kg of the brine per regeneration. The amount of softened water between regenerations is calculated according to the following formula. Z = 1350x10 / Y Where Z – amount of softened water between the regenerations Y –...
  • Page 9 Water hardness (°) English French German Softened degrees degrees degrees water (l) 31,3 45,0 446,5 32,5 46,8 464,4 33,8 48,6 482,2 35,0 50,4 500,1 36,3 52,2 517,9 37,5 54,0 535,8 38,8 55,8 553,7 40,0 57,6 571,5 41,3 59,4 589,4 42,5 61,2 607,2 43,8...

  • Page 10: Technical Data

    5.3 Technical data Water softening system WEH1350 Name System protection for dishwashers 109889 Code-No.:  digital display for adjustment of: water hardness, intervals, regeneration, time, language Design:  regeneration: optionally adjustable via flow rate or time interval Materia: Plastic Connection capacity:...

  • Page 11: Control Function

    5.4 Control function Control valve The control valve is delivered pre-set to the A-03 option (smart regeneration (Downflow)). This setting performs the regeneration at 2 a.m., every 675 litres (0.675 m3) with the water hardness of 20 German degrees. Depending on the water hardness, adjust the amount of water and time of regeneration. Control system (soft water) If the water is too soft, open the adjusting screw (see fig.

  • Page 12: Preparation To The Installation

    6.2 Preparation to the installation. CAUTION! Before the installation check the technical data and during the installation observe the instructions regarding safety and installation included in this instruction manual. Installation diagram At the site of installation the user should prepare: 1.

  • Page 13: Installation Of The Water Softening System

    6.3 Installation of the water softening system  After preparation for installation, place the softener in the designated place,  When connecting the water softening system follow the instructions on figure 2 on page 38:  connect the water inlet (1) and outlet (2) to the device; ...
  • Page 14  During programming do not change the sequence of stages of the regeneration process. 1. backwash (5 minutes) 2. regeneration agent (brine) rinse (50 minutes) 3. regeneration agent (brine) refill (30 sec.) 4. fast rinse ( 5 minutes) These are proper settings for the production of the softened water. If they are changed the device will not work properly.

  • Page 15: Control Panel, Indicators, Button Functions

    6.4 Control panel, indicators, button functions Fig. 3 Digital display Menu/approve select button Manual regeneration/return button Reduce button Increase button Button functions - press this button to select the menu option and approve the selected or changed value change is signaled with a short beep press this button to manually start the regeneration, in order to directly set the regeneration cycles select "InService"...

  • Page 16: Settings

    Button lock If an indicator is shown at the top on the left-hand side of the display, the device informs that the buttons are locked. In order to remove the lock, simultaneously press buttons and hold for 5 seconds. If the settings are not changed within 1 minute, the button lock is activated automatically.
  • Page 17 Displayed Setting option Action information Mode of Press the button to move to the operation option „Mode of operation setting “. setting Default setting: Default setting: A-03 – smart regeneration. A-03 – smart This means that the control valve regeneration „forecasts", whether the volume of the treaded water is sufficient for the next day before activating the next cycle of...
  • Page 18 Displayed Setting option Action information Setting the Press the button to move to the remaining advanced setting mode. amount of water Press the button to select the option: “Setting the remaining Default setting: amount of water: 675 L (0.675 m for the water Press button to select...

  • Page 19: Service Instructions

    6.6 Service instructions Regeneration agent (brine) refill: 1. Remove the cover from the brine tank. 2. Add salt tablets to the brine tank (max. 10 kg). Tip: All the added tablets must be covered with water. 3. Close the cover. CAUTION! Never use the device without the regeneration agent.

  • Page 20: Possible Malfunctions

    7. Possible malfunctions Problem Cause Solution 1. During the water Clogged sewer drain. - Check the sewer drain hose. treatment the water Remember, that the sewer is leaking from the drain pipe needs to have bypass valve of the free flow and clean the water softening sewer drain.
  • Page 21 Problem Cause Solution 5. The water Carbonate hardness Measure the total hardness. measured. softening device delivers hard water Not enough water in the Check settings: water refilling but the amount of brine tank. time. salt in the tank is The water softening device Check the connections of the decreasing.
  • Page 22 Problem Cause Solution 6. Water softening Dry salt Grind the salt manually. system delivers Prepare a salt solution in a hard water. The bathtub (dissolve ca. 1.5 kg of amount of water is salt in 6 litres of hot water). the same as the Pour the brine to the brine amount in the brine...
  • Page 23 Problem Cause Solution 8. The device is using Too much water in the brine Reduce the time of the brine tank. too much salt. tank refilling with water, see problem 9 „Too much water in the brine tank” Too frequent water Check the water hardness treatment.
  • Page 24 Problem Cause Solution 10. The device does Clogged or damaged Call for service not take in the injection valve. brine from the Leak between the brine Call for service brine tank. valve (air control) and the control valve. Insufficient pressure in the water supply system.
  • Page 25 Problem Cause Solution 13. Loss of water Installation supply pipe or Use the installation pipe or pressure. supply hose / outlet of the hose with higher diameter. water softening system has insufficient diameter. Air in the system. Check the system to make sure that there is a brine in the brine tank.
  • Page 26 Problem Cause Solution 18. Water tastes salty. Too short time of brine Change the programming, treatment or too fast rinsing. set the correct time of brine treatment and rinse (see page 31). Air inside the device. The Call for service air may get there during the suction up process.
  • Page 27 Problem Cause Solution 20. Performance of the Wrong execution of water Check the water treatment water softening treatment. cycles. Correct the water device decreases treatment cycles and replace after a few months the resin. or years. Frequent lack of salt or Replace the resin and make insufficient amount of salt in sure that the amount of salt is...

  • Page 28: Disposal

    Disassemble the device for the final disposal following the installation sequence in reverse order. CAUTION! For the disposal of the device please consider and act according to the national and local rules and regulations. Bartscher GmbH Franz-Kleine-Str. 28 D-33154 Salzkotten phone: +49 (0) 5258 971-0 Germany fax:...

Table of Contents