Summit Treestands Hex SU82097 Manual

Summit Treestands Hex SU82097 Manual

Ladder treestand
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

The Hex Ladder Treestand
SU82097
© 2016 Summit Treestands, LLC | 715 Summit Dr. Decatur, AL 35601
READ, FOLLOW AND UNDERSTAND ALL WRITTEN AND VIDEO WARNINGS AND INSTRUCTIONS BEFORE USE. INSPECT ALL EXPIRATION TAGS
PRIOR TO EACH USE. IF YOU DON'T COMPLETELY UNDERSTAND SAFE AND PROPER USE OF THE FULL BODY FALL ARREST HARNESS
SYSTEM (FBFAHS) OR TREESTAND, HUNT FROM THE GROUND! FAILURE TO FOLLOW ALL WARNINGS AND INSTRUCTIONS LISTED COULD
RESULT IN SERIOUS INJURY OR DEATH! IT IS REQUIRED THAT YOU WATCH AND UNDERSTAND THE DVD SUPPLIED WITH THIS PRODUCT &
THOSE SAFETY WARNINGS AND INSTRUCTIONS POSTED AT: www.summitstands.com/safety-videos
WHEN HUNTING FROM A TREESTAND, FALLS CAN OCCUR ANY TIME AFTER LEAVING THE GROUND! ANY FALL CAN CAUSE SERIOUS INJURY
OR DEATH! THE USE OF A FULL BODY FALL ARREST HARNESS SYSTEM (FBFAHS) IS REQUIRED WHEN USING ANY TREESTAND. IF FBFAHS IS
NOT PRESENT, HUNT FROM GROUND LEVEL!
THE USE OF THIS PRODUCT REQUIRES THE USE OF A FULL BODY FALL ARREST HARNESS SYSTEM (FBFAHS). THE FBFAHS MUST BE USED
AND ATTACHED TO THE TREE PRIOR TO GAINING ENTRY UPON THE TREESTAND PLATFORM, AND SHOULD BE WORN AND ATTACHED TO THE
TREE AT ALL TIMES WHILE USING THE TREESTAND UNTIL SAFELY BACK AT GROUND LEVEL. READ AND FOLLOW ALL INSTRUCTIONS THAT
WERE PROVIDED WITH YOUR FBFAHS.
DO NOT USE THIS PRODUCT UNTIL YOU UNDERSTAND SAFE AND PROPER USE. READ AND FOLLOW ALL INSTRUCTIONS AND WARNINGS
PRIOR TO EACH USE!
ALWAYS WEAR A FBFAHS THAT MEETS STRINGENT, INDUSTRY STANDARDS RECOGNIZED BY THE TMA. WEAR A FBFAHS EVERY TIME YOU
LEAVE THE GROUND, INCLUDING ASCENDING OR DESCENDING. SINGLE BELT STRAPS AND CHEST HARNESSES ARE NO LONGER ALLOWED
AND SHALL NOT BE USED! FAILURE TO USE A FBFAHS COULD RESULT IN SERIOUS INJURY OR DEATH!
THE LENGTH OF THE HARNESS TETHER SHALL BE MINIMIZED AT ALL TIMES. IT SHALL BE ADJUSTED SO THAT IT IS ABOVE THE HEAD WITH
NO SLACK (OR SNUG) IN THE SEATED POSITION AND YOU SHALL HAVE MINIMUM AMOUNT OF SLACK POSSIBLE WHEN CLIMBING. FAILURE TO
DO SO MAY RESULT IN SUSPENSION WITHOUT THE ABILITY TO RECOVER TO YOUR TREESTAND. BE AWARE OF HAZARDS ASSOCIATED WITH
HANGING SUSPENDED IN A FBFAHS AND THE FACT THAT PROLONGED SUSPENSION IN A HARNESS MAY BE FATAL.
ALWAYS NOTIFY SOMEONE OF YOUR HUNTING LOCATION IN CASE OF AN EMERGENCY. IF OTHERS ARE NOT AWARE OF YOUR HUNTING
LOCATION AND COMMUNICATION EFFORTS ARE UNSUCCESSFUL, YOU MUST HAVE A PERSONAL PLAN FOR RECOVERY/ESCAPE BEFORE
YOU ASCEND THE TREE - PROLONGED SUSPENSION IN A HARNESS CAN BE FATAL. IT IS IMPORTANT TO EXERCISE THE LEGS BY PUSHING
AGAINST THE TREE OR DOING OTHER FORMS OF CONTINUOUS LEG EXERCISES TO AVOID BLOOD POOLING WHILE BEING SUSPENDED.
HUNTERS WITH VARYING DEGREES OF PHYSICAL FITNESS MAY REQUIRE DIFFERENT PLANS TO RECOVER/ESCAPE IN ORDER TO AVOID
EFFECTS OF PROLONGED SUSPENSION. HAVE A PERSONAL PLAN AND PRACTICE IT IN THE PRESENCE OF A RESPONSIBLE ADULT BEFORE
LEAVING THE GROUND. NO ESCAPE/RECOVERY PLAN WILL WORK FOR EVERY HUNTER ON EVERY TREE IN EVERY CIRCUMSTANCE. ONLY
YOU CAN DETERMINE THE BEST RECOVERY/ESCAPE PLAN FOR YOUR HUNTING SITUATION AND YOU MUST HAVE A RECOVERY/ESCAPE PLAN
FOR YOUR SITUATION BEFORE LEAVING THE GROUND. HUNT FROM GROUND WHEN SELF-RECOVERY/ESCAPE ABILITY IS ABSENT.
IF THERE ARE ANY QUESTIONS OR CONCERNS WITH INSTRUCTIONS, WARNINGS, OR PROPER USE "STOP" AND CONTACT THE
MANUFACTURER. DO NOT USE UNLESS YOU FULLY UNDERSTAND SAFE AND PROPER USE. MAINTAIN ALL WARNINGS, INSTRUCTIONS, AND
DVD(S) FOR LATER REVIEW AS NEEDED, FOR INSTRUCTION USAGE TO ANYONE BORROWING YOUR STAND/FBFAHS OR TO PASS ON WHEN
SELLING THESE ITEMS. USE ALL SAFETY DEVICES PROVIDED WITH YOUR TREESTAND AND FBFAHS.
INSPECT THE TREESTAND PRIOR TO EVERY USE FOR UNDUE WEAR, DEFORMITY, CORROSION OR OTHER DAMAGE. INSPECT ALL STRAPS,
WEBBING AND ROPES FOR FRAYING, CUTS, TEARS, ABRASIONS, FADING, NICKS, CUTS OR ANY SIGNS THAT THE WEBBING MAY HAVE
BEEN FATIGUED OR STRESSED BY A FALL OR BY SUPPORTING EXCESS WEIGHT OR ANY OTHER TYPE OF DAMAGE. DISCONTINUE USE
IMMEDIATELY IF ANY DAMAGE IS PRESENT.
THIS TREESTAND IS INTENDED FOR SINGLE PERSON USE ONLY!!
NEVER EXCEED THE MAXIMUM RATED WEIGHT LIMIT OF THIS PRODUCT. THIS LIMIT INCLUDES USER AND ALL GEAR TAKEN TO THE
PLATFORM AREA.
MOST FALLS IN A LADDER OCCUR DUE TO IMPROPER INSTALLATION OR BY NOT USING THE PRODUCT AS DIRECTED. ALL SUPPLIED PARTS
MUST BE USED, INCLUDING, BUT NOT LIMITED TO, THE STABILIZER BAR, ATTACHMENT STRAPS AND ALL REQUIRED HARDWARE. LADDER
SECTIONS CONNECTIONS MUST BE SECURED TOGETHER BY MEANS OF THE PINS OR BOLTS SUPPLIED. CAREFULLY FOLLOW AND DOUBLE
CHECK ALL ASSEMBLY INSTRUCTIONS TO ENSURE THAT YOU HAVE PROPERLY ASSEMBLED THE PRODUCT. IF YOU HAVE ANY QUESTIONS OR
CONCERNS, CONTACT SUMMIT AT 800-353-0634.
THE ASSEMBLY AND INSTALLATION OF A LADDER STAND REQUIRES A MINIMUM OF THREE (3) ABLE ADULTS. NEVER ATTEMPT TO ASSEMBLE,
INSTALL, OR REMOVE THIS PRODUCT WITH LESS THAN THREE (3) ABLE ADULTS PRESENT.
REPLACE ALL WEBBING AND CABLES EVERY (2) YEARS OR SOONER IF ANY DAMAGE IS PRESENT INCLUDING BUT NOT LIMITED TO FRAYING,
CORROSION, CUTS, TEARS, ABRASIONS, FADING, NICKS, CUTS OR ANY SIGNS THAT THE WEBBING OR CABLES HAVE BEEN FATIGUED OR
STRESSED BY A FALL OR BY ANYTHING INCLUDING BUT NOT LIMITED TO SUPPORTING EXCESS WEIGHT. IF ANY OF THE DAMAGE STATED
ABOVE (OR ANY OTHER TYPE OF DAMAGE NOT LISTED) IS PRESENT, DISCONTINUE USE OF THE PRODUCT IMMEDIATELY!
DO NOT USE ANY TREESTAND IF ICE OR SNOW IS PRESENT ON THE PLATFORM OR LADDER SECTIONS.
ALWAYS HAVE THREE (3) POINTS OF CONTACT TO THE LADDER WHILE CLIMBING. NEVER CLIMB WITH ANYTHING ON YOUR BACK OR IN YOUR
HANDS WHILE CLIMBING. TAKE YOUR TIME, DO NOT BE IN A HURRY!!
PRINTED IN CHINA
PH#: (800) 353-0634 | www.summitstands.com
WARNING
!
FAILURE TO READ AND FOLLOW ALL MANUFACTURER'S
WARNINGS AND INSTRUCTIONS CONSTITUTES A MISUSE OF THIS
PRODUCT AND COULD RESULT IN SERIOUS INJURY OR DEATH!!
Hex 82097, 02/2016

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Hex SU82097 and is the answer not in the manual?

Questions and answers

Summary of Contents for Summit Treestands Hex SU82097

  • Page 1 The Hex Ladder Treestand SU82097 WARNING © 2016 Summit Treestands, LLC | 715 Summit Dr. Decatur, AL 35601 PH#: (800) 353-0634 | www.summitstands.com FAILURE TO READ AND FOLLOW ALL MANUFACTURER’S WARNINGS AND INSTRUCTIONS CONSTITUTES A MISUSE OF THIS PRODUCT AND COULD RESULT IN SERIOUS INJURY OR DEATH!! •...
  • Page 2 • PRIOR TO EACH USE INSURE: • THE CRISS/CROSS STRAPS ARE PRESENT AND SECURED CORRECTLY. • THE ADJUSTABLE STABILIZER BAR IS PRESENT AND SECURED PROPERLY. • ALL LADDER SECTIONS ARE NOT SEPARATED AND SECURED TOGETHER BY MEANS OF PINS OR BOLTS. •...
  • Page 3 TREE SIZE / WEIGHT LIMIT Stand Minimum and Maximum Tree Size: 8-20” Diameter Weight Limits: (Includes hunter’s weight PLUS weight of all gear carried into the treestand) DO NOT EXCEED THESE WEIGHT LIMITS! 350 lb Rated Stand: SU82097 - The Hex THIS TREESTAND IS INTENDED FOR SINGLE PERSON USE ONLY!! STAND / COMPONENT WARNING LABELS (FOR REFERENCE ONLY)
  • Page 4: Parts List

    PARTS LIST Please call 800-353-0634 or visit http:// www.summitstands.com/contactus/ if you have any questions, if you need replacement parts, if you have any missing parts or if the included DVD does not play. All images are representations. All fabric, paint and accessories are subject to change at any time.
  • Page 5: Tools Required

    TOOLS REQUIRED Tools • 13mm Wrenches and / or Socket / Ratchet - Assembly can be made easier by the use of a powered ratchet or drill with socket adapter (take care not to overtighten when using power tools to assemble) - It is recommended that all bolts be sorted by thread count / length prior to assembly.
  • Page 6 3. Place the Seat Support Frame (item E) welded tube to the second (2nd) hole from the Connection Tube end and align the holes together. See figure 5 and 6. BOLT LOCATION ON BOTTOM CONNECTION TUBE SIDE OF CONNECTION TUBE 4.
  • Page 7 8. Place the Arm Rest (item G) onto the BOTTOM side of the Connection Tube (item F) and secure using (2) 65mm bolts with lock nuts. See figure 11. Repeat for the other Arm Rest. SHOOTING RAIL ASSEMBLY 9. Insert Gun Rest Rail 1 (item K) onto the OUTSIDE of the Arm Rest (item G) and secure using two 55mm bolts with wing nuts on each side.
  • Page 8: Footrest Assembly

    PLATFORM SUPPORT BARS 11. Place the Platform Support (item I) onto the SIDE of the Seat Support Frame and secure with (2) 65mm bolts and lock nuts. See figure 15. Next, secure the opposite end of the Platform Support to the BACK-SIDE of the Top Ladder Section using (2) 65mm bolts with locknuts.
  • Page 9: Ladder Section Assembly

    LADDER SECTION ASSEMBLY 14. Assemble the remaining Ladder Sections together. Insert the “male” end of the Ladder Section into the “female” end of the opposing ladder section. Secure the two sections together using (2) 35mm (Grade 10.9) bolts per side. Secure tightly. See figure 20 and 21.
  • Page 10 WARNING SETUP Never use this ladder stand on dead, leaning, diseased or loose barked trees. Never use on a utility pole or on trees that have any obstructions that may limit 1. Select a straight, healthy tree without any obstructions (branches or treestand use.
  • Page 11 6. Connect the remaining two looped ratchet ends to the column of the ladder section below the third (3rd) or fourth (4th) ladder rung from the end. Follow the procedure in step 4 to create a cinch knot. See figure 25-27 (for threading) and 30 (for location).
  • Page 12 10. Take the two (2) straps that are hanging freely down, walk behind the tree so that the straps form an “X” in the straps as shown in figure 36. Pull the straps around to the bottom ladder section and secure the straps to the previously installed ratchet straps below the third or fourth ladder rung.
  • Page 13 WARNING WARNING Never jump or bounce on any You MUST now put on your safety harness if you have other part of the treestand not already done so. ALWAYS refer to your harness in an attempt to force the instructions included with this stand for proper use of platform to seat into the tree.
  • Page 14 WARNING NEVER re-use ratchet straps that were left in the field for use. Call Summit Treestands to purchase replacement straps. Sunlight, animals, or tree growth could have affected the strap integrity which could cause the strap to fail, causing serious injury or death! PG 14 www.summitstands.com...
  • Page 15: Maintenance And Care

    (A) Warranty Summit Treestands, LLC (Summit) warrants to the original retail purchaser that all products manufactured by it are free from defects in material and manufacture at the time of shipment for twelve (12) months from the date of purchase. Summit will repair or replace any part found defective if the unit claimed to be defective shall be returned to Summit, postage prepaid, within the warranty period.
  • Page 17 The Hex Mirador à échelle SU82097 AVERTISSEMENT © 2016 Summit Treestands, LLC | 715 Summit Dr. Decatur, AL 35601 PH#: (800) 353-0634 | www.summitstands.com NE PAS LIRE ET NE PAS SUIVRE LES AVERTISSEMENTS ET LES INSTRUCTIONS DU MANUFACTURIER CONSTITUE UNE MAUVAISE UTILISATION DU PRODUIT ET PEUT ENTRAÎNER...
  • Page 18 • AVANT CHAQUE UTILISATION ASSUREZ-VOUS QUE: • LES COURROIES ENTRECROISÉES SONT PRÉSENTES ET ATTACHÉES CORRECTEMENT. • LA BARRE STABILISATRICE AJUSTABLE EST PRÉSENTE ET ATTACHÉE CORRECTEMENT. • LES SECTIONS DE D’ÉCHELLES NE SONT PAS SÉPARÉES ET SONT ATTACHÉES ENSEMBLE AVEC LES GOUPILLES ET LES BOULONS. •...
  • Page 19 GROSSEUR D’ARBRE/LIMITE DE POIDS Vous devez également visionné le DVD ci-joint AVANT d’utiliser votre nouveau mirador!! LIMITE DE POIDS LIMITE DE POIDS POUR OCCUPATION INDIVIDUELLE 136 KGS. X 1 TOTAL* NE DÉPASSER PAS CETTE LIMITE! (* Inclus tout l’équipement) Grosseur d’arbre minimum et maximum pour le mirador: 20-50 cm de diamètre Évalué...
  • Page 20 LISTE DES PIÈCES Appellez le 800-353-0634 ou visitez le site web à l’adresse http://www. summitstands.com/contactus/ si vous avez des questions, si vous avez besoin de pièces de remplacement, si des pièces sont manquantes ou si le DVD inclus est défectueux. Toutes les images sont des représentations visuelles.
  • Page 21: Outils Requis

    OUTILS REQUIS Outils • Clés 13mm / ou Douille / Rochet - L’assemblage peut être facilité avec l’utilisation d’un rochet électrique ou d’une perceuse avec douille (assurez-vous de ne pas serrer trop fort lors de l’assemblage avec des outils électriques). - Il est recommandé...
  • Page 22 3. Placez le tube soudé du châssis de support du siège (item E) au deuxième trou du bout du tube de connexion et alignez les trous. Voir les figure 5 et 6. EMPLACEMENT DU BOULON SUR LE CÔTÉ TUBE DE CONNEXION INFÉRIEUR DU TUBE DE CONNEXION 4.
  • Page 23 8. Placez l’appui-bras (item G) sur la partie INFÉRIEURE du tube de connexion (item F) et attachez-le avec deux boulons de 65mm et des écrous de blocage. Voir la figure 11. Répétez la procédure pour l’autre appui-bras. ASSEMBLAGE DE LA RAMPE DE TIR 9.
  • Page 24 SUPPORT DE PLATEFORME 11. Placez le support de la plateforme (item I) sur le CÔTÉ du châssis du support du siège et attachez-le avec deux boulons de 65mm et des écrous de blocage. Voir la figure 15. Puis, attachez le bout opposé du support de la plateforme à l’ENDOS de la section d’échelle supérieure avec deux boulons de 65mm et des écrous de blocage.
  • Page 25 ASSEMBLAGE DE LA SECTION D’ÉCHELLE 14. Assemblez les autres sections d’échelle ensemble. Insérez la partie ‘’mâle’’ de la section d’échelle dans la partie ‘’femelle’’ de la section d’échelle opposée. Attachez les deux sections ensemble avec deux boulons de 35mm (Grade 10.9) de chaque côté. At- tachez fermement.
  • Page 26: Installation

    AVERTISSEMENT INSTALLATION N’utilisez jamais ce mirador à échelle sur un arbre mort, penché, malade ou qui possède une écorce détachée. Ne jamais l’utiliser sur un poteau utilitaire ou sur des arbres près 1. Choisissez un arbre droit, en santé sans obstructions (branches) qui pourraient desquels se trouvent des obstructions qui pourraient limiter représenter un obstacle à...
  • Page 27 6. Attachez les deux bouts restants des sangles bouclées à la colonne de la section d’échelle se trouvant sous le troisième ou le quatrième barreau de l’échelle à partir de la fin. Suivez la procédure à l’étape 4 afin de créer un nœud sanglé. Voir les figures 25-27 (pour l’enfilage) et la figure 30 (pour l’emplacement).
  • Page 28 10. Prenez les deux courroies libres, allez derrière l’arbre de sorte que les courroies forment un ‘’X’’ tel qu’illustré à la figure 36. Tirez les courroies autour de la section d’échelle du bas et attachez les courroies aux courroies à cliquet préalablement installées sous les deuxièmes et le troisièmes barreaux d’échelle.
  • Page 29 AVERTISSEMENT AVERTISSEMENT Vous DEVEZ maintenant mettre votre harnais de sécurité Ne sautez ou ne bondissez si ce n’est déjà fait. Veuillez TOUJOURS vous référer aux jamais sur toute partie du instructions de votre harnais incluses avec ce mirador pour mirador pour forcer son l’utilisation correcte de votre harnais de sécurité.
  • Page 30 ENLÈVEMENT DE L’ÉCHELLE 1. Il est requis d’avoir trois (3) adultes responsables pour vous aider à enlever ce mirador à échelle de l’arbre. Avant de monter dans un mirador à échelle, revêtez votre HCCSAC et suivez les instructions et avertissements pour l’utilisation sécuritaire et correcte.
  • Page 31: Entretien Et Soin

    (A) Garantie La compagnie Summit Treestands, LLC (Summit) garantie à l’acheteur original que tous ses produits manufacturés sont sans défauts du matériel et de fabrication lors de l’expédition et ce pour douze (12) mois à partir de la date d’achat. Summit remplacera toute pièce défectueuse si le module soi-disant défectueux est retourné...

Table of Contents