Table of Contents
Advertisement
Make sure not to damage any cables. Verify that the cables are not tangled
and that they are not able to get caught in any in moving parts during use.
5. CLEANING AND DISINFECTING
In case of replacement of any individual components, always make sure that
the electric plugs are then properly inserted into the controller. Only in this way
5.1 GENERAL INFORMATION
will the bed function properly.
Clearing is fundamental as well as a proper chemical disinfection. In general, regular cleaning of the bed when used by
a single patient is sufficient in terms of hygiene. It is necessary to disinfect the bed frame only in case of a visible conta-
3.1.1 Use of accessories
mination with contagious or potentially contagious materials (ex. blood, urine, pus etc.) or in case of a contagious disease
upon request by the physician.
Apollo Healthcare Technologies can supply various accessories for use with this bed
Every time the bed is used by a new patient, it is mandatory to first clean and then disinfect the bed by scrubbing
including a lifting pole, bed lever and dynamic mattress systems. For correct installation of
thoroughly!
accessories please refer to section 4 of this manual.
Before you start clearing:
Use of non-Apollo Healthcare Technologies accessories is not advised. Installing
•Remove the plug from the socket and make sure it does not come into contact with water or disinfectant.
third party accessories could restrict the moving parts of the bed. The warranty
•Make sure all plugs are properly connected.
does not cover any damages caused by use of third party accessories and your
•None of the electric components must be externally damaged to avoid the penetration of water or disin-
warranty could be void if third party accessories are installed and used.
fectant liquids which might lead to malfunctioning or damages to the electric components.
Before using the bed again, by drying or blowing in the power plug, make sure there is no residual moisture left in
3.2 Operations
the electrical contacts.
• The electric components must not be subjected to a water jet, a high pressure cleaner or anything similar! Cleaning
should be done with a damp cloth!
Every time before using the bed, the user must make sure that:
• If you suspect that water or moisture have entered into the electric components, immediately remove the power
• the wheels of the bed are locked (see also chapter 4.3).
plug from the socket outlet and do not plug it in again.
• the power supply is compatible with the bed (230 Volt, 50 Hertz).
Mark clearly the bed with a "Faulty" sign and make sure it cannot be used. Inform immediately the owner of the bed
• the power cable is plugged in and placed in such a way that it cannot be damaged.
about the problem.
• the power cable, the motor cables and the hand control cable are not damaged by
In case of non-compliance with these safety rules, it is not possible to exclude the risk of serious damages to the bed
any moving parts of the nursing bed.
with related consequences!
• there are no obstacles in the way such as bedside furniture or chairs.
• all accessories used are installed correctly and do not restrict the free movement of any
part of the bed especially the backrest and knee break mattress platform.
5.2 CLEANING AND DISINFECTION PROGRAM
• all control functions have been accurately inspected (see also chapter 6.1) and are
working properly.
• Remove the sheets from the bed to be washed.
• only after carrying out the above operations should the bed be regarded as safe to use.
• Clean all surfaces including the mattress platform, the plastic inserts and cables with a mild non aggressive detergent,
including the hand control.
3.2.1 Requirements of the installation site
• The bed should be disinfected by scrubbing using a disinfectant recommended for hospital use especially in case of
visible contamination with contagious or potentially infectious material. The same as applicable to beds in intensive care
• Make sure there is enough space to safely allow the whole range of adjustments of the
or infectious diseases units.
bed. There should not be any furniture or other objects close to the bed such as window
• It is necessary to disinfect the wheels only in case of visible contamination with infectious or potentially infectious
cills.
material.
• If the bed is to be used on parquet floor, make sure that the use of wheels will not cause
any discolouring due to the parquet waterproof treatment. It is possible to use the bed
Note: A continuous disinfection is necessary only in case of patients with multi-resistant pathogens within a hospital
on tiles, carpets, laminated floors and linoleum.
• A 230 volt power outlet, correctly installed, must be located as near as possible to the
bed.
5.3 TRAINING OF USERS AND SPECIALIZED PERSONNEL
• If there is the need to use other accessories (such as compressor systems, bed levers
etc...), make sure they are correctly fixed and that they work properly. In particular, make
To ensure a proper cleaning and disinfecting procedure, we recommend you to appropriately train all users and specia-
sure all different cables are safely connected and no moving part of the bed is restricted
lized personnel involved. The following points must be respected:
from moving freely as it should. In case of questions or doubts please contact the
manufacturer of such accessories.
• Make sure the bed does not get soiled or contaminated during transport to the patient's house.
• In case of disassembly of the bed, it is necessary to immediately clean and disinfect it by scrubbing. The personnel must
be informed about the correct cleaning and disinfecting procedure and carry out his/her necessary treatment properly
(according to the steps of the procedure notified by the owner). The disinfectant used must be suitable for the treated
surface.
• For this operation the specialized personnel shall be provided with waterproof disposable gloves and aprons.
• For the treatment only clean cloths should be used which must then be taken to be washed.
• After the treatment the personnel should disinfect their hands before leaving the place to go somewhere else. The
qualified personnel must be equipped with a disinfectant with dispenser.
Cleaning of the bed directly on site has the advantage that the bed and/or none of its parts can get «soiled» when then
transported in the same vehicle with other clean beds. Itprevents potentially infectious germs located in the bed frame
from spreading around.
These recommendations will help to prevent nosocomial infections. If the beds are not immediately reused, they should
be stored away with a cover to protect from dust and accidental contamination.
Made by NAUSICAA Medical S.A.S. / Approved by Ghizlane Labrosse (Biomedical Engineer)
12
User Manual / CONVERTISS FOLDING PREMIUM
13
Advertisement
Table of Contents
