Digital Watchdog Star-Light Plus DWC-V6563WTIR Quick Start Manual

Quick Start Guide
DWC-V6563WTIR
Torx Wrench
WHAT'S IN THE BOX
Torque Quick Setup
1 Set
wrench Torx Wrench DC Plug Cable Guide
Torx Wrench DC Plug Cable Test Video Cable
Template Sheet
Screws
DC plug and plastic
1 Set
cable anchors
Torx Wrench DC Plug Cable Test Video Cable
(4pcs)
Sunshield cover &
Torx Wrench DC Plug Cable Test Video Cable
Template Sheet Manual
Screw &
Moisture ab-
Template Sheet Manual
Test video sorber and
1 Set
cable absorber
Torx Wrench DC Plug Cable guide Test Video Cable
Sunshield cover &
DC Plug Cable
Test Video Cable
Screw &
Template Sheet Manual
Screw & Moisture absorber &
Template Sheet Manual
Mounting
Absorber Guide
template 1 Set
sheet
Template Sheet Manual
Screw & Moisture absorber &
Manual
Absorber Guide
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in
the 'Search by Product' search bar. Results for
applicable part numbers will populate automatically
based on the part number you enter.
3. Click 'Search'. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
Attention: This document is intended to serve as a quick reference for
initial set-up. It is recommended that the user read the entire instruction
manual for complete and proper installation and usage.
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
STEP 1 – PREPARING TO MOUNT THE CAMERA
1. The mounting surface must withstand five times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover can be damaged. This may cause a
short or fire.
3. Install the moisture packet in the base of the camera's lens.
a. Remove the moisture absorber from the packaging.
b. Cut the card and folder along the dotted line.
c. Place the moisture absorber behind the camera's lens module. See drawing for more information.
4. Detach the camera's dome cover by loosening the four (4) screws on each side of the dome.
5. Remove the dome protection film before placing the dome back on the camera base.
Sunshield cover &
6. Using the mounting template sheet or the camera itself, mark and drill the necessary holes
DC Plug Cable Test Video Cable
in the wall or ceiling.
1 Set Sunshield cover &
Test Video Cable
Sunshield cover &
Screw & Moisture absorber &
Manual
Absorber Guide
1 Set
Sunshield cover &
Screw & Moisture absorber &
Absorber Guide
Moisture absorber &
Absorber Guide
Please cut the card type absorber along
1 Set
Sunshield cover &
a dotted line, overlap and attach them
Moisture absorber &
according to the direction of the arrow.
Absorber Guide
Screw & Moisture absorber &
Absorber Guide
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
Pass the wires through the mount bracket and make all necessary connections. Connect the BNC cable and power cables to the camera.
digital-watchdog.com
Please cut the card type absorber along
a dotted line, overlap and attach them
according to the direction of the arrow.
Power Requirements
DC12V/AC24V dual voltage
Quick Start Guide
Protection
film
Please cut the card type absorber along
a dotted line, overlap and attach them
according to the direction of the arrow.
Power Consumption
DC12V (LED off): 3.3W (275mA)
DC12V (LED on): 5.9W (495mA)
AC24V (LED off): 2.75W (200mA)
AC24V (LED on): 5.3W (360mA)