SECOLink PAS8 Series Manual page 5

Intruder alarm system
Normally closed Normally closed
contact with one
contact
(NC)
PAS8xx or module PAS8xx or module
+AUX COM Z1 COM +AUX COM
+12V COM T1 T2 COM NC +12V COM
Tamper
Sensor
Wiring of double zones (only PAS832)
PAS832
+AUX COM Z1 COM
300 1k
+12V COM T1 T2 COM NC*
Tamper
Sensor A
* - Sensor contact type may be NC or NO.
To COM
PAS8xx
+PGM COM Z5 COM
To zone
+12V COM COM NO
The contacts of smoke detector
Note: the smoke detectors made by
different manufacturers may have a
different contact layout. For more
detailed information about contact
Detector
layout look the documentation
supplied by manufacturer of smoke
detector.
Normally closed
contact with two
resistor resistors
(NC/EOL) (NC/DEOL)
PAS8xx or module
Z1 COM +AUX COM
1k
T1 T2 COM NC +12V COM
Tamper Tamper
Sensor Sensor
620
+12V COM T1 T2 COM NC*
Tamper
Sensor B
Wiring of 4-wire smoke detector
To COM
The smoke detectors may be triggered by dust, so in
order to prevent false alarms it is necessary to
execute an trigger re-check. For achievement of this
objective an attribute "Fire verification" has to be
assigned to the system's fire zone, the smoke
detector has to be powered by PGM output with
definition "Fire Power Supply"and the fire zone has to
be assigned to the corresponding PGM trigger
source. In the template is set that fire zone is the
control panel zone Z5, the +PGM2 output is used for
power supply of smoke detectors.
Operation: In order to check the triggered smoke
detector it's power supply has to be turned OFF and
To +PGM
turned ON again. The system turns OFF the PGM
output for a time equal to PGM trigger time. When this
time expires the system turns ON the PGM output
again and waits for detector operating status settling
("Detector settling time"). The system executes the
detector trigger re-check with duration equal to "Fire
verification time". If during this time the smoke
detector is triggered again the system raises a fire
alarm and sends report, if there are no smoke detector
trigger the system does not alarm.
Wiring of zones
Wiring of single zones
Normally open
contact
(NO)
PAS8xx or module
Z1 COM +AUX COM
1k 1k
T1 T2 COM NC +12V COM T1 T2
Tamper
Sensor
ATTENTION! Sensors must be wired without loops
PAS832
Sensor B
Sensor A
Wiring samples
Control Panels PAS8xx Control Panels PAS8xx
Short wiring manual – basic information
Normally open contact
with one resistor
(NO/EOL)
PAS8xx or module
Z1 COM +AUX COM Z1 COM
1k
COM NO +12V COM T1 T2 COM
Tamper
Sensor
Correct sensor wiring
Sensor
Cable
Sensor
Cable
PAS8xx
Wrong sensor wiring
Sensor
Cable
Sensor
Cable
PAS8xx
Wiring of relays
PAS8xx or module
+PGM COM
D1
Relay
NC NC NO NO
For relay wiring it is recommended to use the
protective diode which would limit the induced
current appearing during turning OFF the relay.
Normally open contact
with two resistors
(NO/DEOL)
PAS8xx or module
+AUX COM Z1 COM
1k 1k
NO +12V COM T1 T2 COM NO
Tamper
Sensor
Sensor
Cable
EXM800
Sensor
EXM800
PAS8xx or module
+AUX -PGM
D1
Relay
NC NC NO NO
Page 5