Advertisement
Legends - Renegade GPS Speedometer Cluster - Figures #4 - #8
See Figures 2 and 3 for more wiring and installation information.
FIGURE 4: OPTIONAL Backup Speedometer Sender Connection
Connect to the speedometer
pulse signal. Acceptable
signals ranging from 1V - 100Volts.
500 - 250,000 pulses per mile.
Alternate ECU Setup: You can connect signal wire directly to the speedometer signal out on the vehicle's ECU.
FIGURE 5: Fuel Level Sender Connection
Note: When gauge power is off the pointer(needle)
will remain in last powered position.
(white)
fuel sender output
fuel sender ground
(black)
Note: Fuel sender ground should be
connected to the fuel level sender
ground. If you do not have a fuel
level sender ground connect to the
chassis ground.
FIGURE 6: Temperature Sender Connection
Trimable area
Harness Wires:
White wire - Signal
Black wire - Ground
DO NOT trim pass the slot.
FIGURE 7: OBDII Setup
Does your vechicle support the CAN-BUS protocol?
Vehicle's OBDII connector pin numbering
OBDII CAN (J1979) protocol Pinout:
If the vehicle has wires that connect to pins 6 and 14 of the
OBDII connector then the vehicle supports the CAN-BUS
(J1979) protocol.
Pin 4 -- Chassis Ground
Pin 5 -- Signal Ground
Pin 6 -- CAN High (data)
Pin 14 -- CAN Low (data)
Pin 16 -- +12volt Battery power (NOT a source for gauge power)
FIGURE 8: GPS Antenna and Hot Start Wire
1. Connect GPS receiver antenna into back of speedometer.
2. For best performance, mount GPS antenna with as much view of sky as possible (preferably on the roof of
the vehicle). The GPS antenna is waterproof and magnetic. If the car's roof is not accessible then mount the
antenna on top of the vehicle's dash with as much exposure as possible to the sky through the window.
NOTE: Antenna is able to receive signal through some thin materials i.e. wood,
glass, fiberglass, and plastic. All types of metal will block the signal.
3. Hot start feature is optional. Connecting the hot start wire to constant +12volts allows GPS to quickly acquire satellites in less than 2 seconds.
This feature saves your current satellite position within the speedometer enabling it to quickly restore your position on power up when Speedometer has been
powered off.
NOTE: Please note that if the speedometer has been powered off longer than 4 hours, it could take up to 1 minute to acquire signal due to the satellites moving significantly
from your location. This is normal.
Power Draw NOTE: The hot start current draw is extremely low (25 micro-amp) and will have virtually zero impact on a vehicle's battery charge. Hot start wire should be
connected directly to battery +12voltage and should remain powered 100% of the time.
(Fuel Level Wiring Harness)
(Temperature Gauge Wiring Harness)
1/8 npt threads
OBDII Note: Speedhut CJ Speedometer gauge will not function when used in conjunction
with any other OBDII device. Cycle the gauge power to restore proper gauge function.
1. Connect power distribution requirements as shown in Figures 2 & 3.
(Make sure that the vehicle battery is disconnected)
2. Connect the black CAN high wire (#4) to the OBDII pin 6, Connect the
white striped black CAN low wire (#6) to the OBDII pin 14.
[CAUTION: Do not connect to a powered OBDII system. Failure to do so will throw
a check engine code.]
3. Mount gauge for easy viewing.
(Requires GPS signal for calibration, See Figure 8)
Speedometer Signal Wire (Red/Green Wire)
(see Gauge Operation Instructions for calibration instructions)
+12Volts Hot Start (Red/Black)
+12 Volts constant power (25 micro-amp draw)
- 4 -
Speedometer
Fuel Level Wires (Pink and Yellow/Black)
Fuel Level Ground gauge wire (Yellow/Black)
Fuel level signal gauge wire (Pink)
Note: When gauge power is off the pointer(needle)
will remain in last powered position.
Temperature Gauge Wires
(Yellow/Red and Yellow/Black)
(Yellow/Black)
(Yellow/Red)
Gauge
GPS ANTENNA
Gauge
Advertisement
