Advertisement
Quick Links
Legends - Renegade GPS Speedometer Cluster
Installation Instructions
1. Disconnect the vehicle battery.
2. Connect the gauge power requirements as shown in figures 2 & 3.
3. Wire all the components to the proper sources and senders. (See figures 2 & 3)
4. Reconnect the vehicle battery.
5. Power up the gauge and program the various gauge components (if needed). (See Gauge Operation Instructions)
FIGURE 1: Gauge Display Guide
Brake Indicator
Left Turn Signal
Temperature
Warning Indicator
Speedometer
WARRANTY - Speedhut Inc. warrants to the consumer for a period of 5 years from the date of purchase that this product will be free from defects in materials or workmanship. Speedhut warrants to the consumer for a
"LIFE-TIME" that the product circuit board will be free from defects in materials or workmanship. This warranty is limited to the repair or replacement of Speedhut Inc products. Speedhut Inc is not responsible for special,
incidental or consequential damages or costs incurred due to the failure of this product. Modification to the product, improper use or installation, accident, water damage, abuse, unauthorized repairs or alterations voids
this warranty. Speedhut Inc disclaims any liability for consequential damages due to breach of any written or implied warranty on all products manufactured by Speedhut Inc. Please contact Speedhut Customer Support
If you have a problem with this product | support@speedhut.com | 801-221-1460 (9am - 5pm MST)
Check Engine Indicator
Temperature Gauge
Tachometer (Not available on some models)
High Beam Indicator
MPH
RPM
Button - Used to operate gauge screen and programming
menus and options.
- 1 -
4 Wheel Drive
(4x4) Indicator
Screen - Displays - mileage,
programming options,
menus, and other useful
information.
Right Turn Signal
Low Fuel Indicator
Fuel Level Gauge
Advertisement
Summary of Contents for Legends Renegade
- Page 1 Legends - Renegade GPS Speedometer Cluster Installation Instructions 1. Disconnect the vehicle battery. 2. Connect the gauge power requirements as shown in figures 2 & 3. 3. Wire all the components to the proper sources and senders. (See figures 2 & 3) 4.
- Page 2 Legends - Renegade GPS Speedometer Cluster FIGURE 2: Wiring Guide Power Draw = 0.2 Amp See Figure #3 for more wiring info. 3A to 5A Inline Fuse Recommended for +12 Blue wire with White Stripe - High Beam Indicator Red wire with Green Stripe - Speed Sensor...
- Page 3 Renegade Cluster - Installation FIGURE 3: Connection Guide See Figure #2 for more wiring information and numbering. left turn signal +12V pulse (#3 Green/Orange) Power Draw = 0.2 Amp right turn signal +12V pulse (#5 Green/Red) 3A to 5A Inline Fuse Recommended...
-
Page 4: Gps Antenna
Legends - Renegade GPS Speedometer Cluster - Figures #4 - #8 See Figures 2 and 3 for more wiring and installation information. FIGURE 4: OPTIONAL Backup Speedometer Sender Connection (Requires GPS signal for calibration, See Figure 8) Speedometer Connect to the speedometer pulse signal. - Page 5 Legends - Renegade GPS Speedometer Cluster - Tachometer Connections (Available on some models) FIGURE 9: Note: If you plan to operate the tachometer using OBDII CAN-BUS (J1979), then you do not need to connect the Tachometer signal wire. Your vehicle ignition system will fall under one of these 4 ignition types. The type of ignition system will determine where the yellow tachometer signal wire (wire #17) is connected and what the number of pulses per revolution the tachometer should be set to.
- Page 6 Legends - Renegade GPS Speedometer Cluster - Gauge Operation Instructions (GPS features) To access and use the on screen menu: Press the button (located on the front of the gauge) to select different options. Press and hold the button to gain access to an option or menu selection.
- Page 7 Legends - Renegade GPS Speedometer Cluster - Gauge Operation Instructions (Fuel Level Calibration, Tachometer Calibration, Set Odometer, and About Screen) Follow these steps below for all menu items 1. Press and hold button down while turning on gauge power to enter the calibration menu.