Do you have a question about the 905180165 and is the answer not in the manual?
Questions and answers
Anna Maria Russo
March 24, 2025
Unable to open lid (Fig. J) to remove and clean filter.
1 comments:
Mr. Anderson
March 24, 2025
To open the lid on a Black & Decker 905180165 and remove and clean the filter, follow these steps:
1. Remove the container: Press the two release buttons (31) and lift the container (9) out of the appliance. 2. Open the lower door: Press the lower door latch (32) to release the dirt. 3. Remove the filter: Take out the filter (35) from the container. 4. Clean the filter: Brush any loose dust off the filter. 5. Replace the filter: After cleaning, reinsert the filter (35). 6. Reassemble the container: Re-insert the container into the appliance, ensuring it clicks into place.
This answer is automatically generated
Anna Maria Russo
March 23, 2025
Cannot open figure J to clean filter
1 comments:
Mr. Anderson
May 14, 2025
To clean the filter, follow these steps:
1. Remove the container (9) from the appliance by pressing the two release buttons (31) and lifting it out. 2. Press the lower door latch (32) to release the dirt. 3. Remove the filter (35) as shown in figure L. 4. Brush any loose dust off the filter. 5. Replace the filter (35) and re-insert the container into the appliance.
Figure J is not mentioned in the context, so it is not required for cleaning the filter.
This answer is automatically generated
Anna Maria Russo
March 23, 2025
May I please have a drawing of what I should do? I,e, how to remove filter?
1 comments:
Mr. Anderson
March 23, 2025
To remove the filter for Black & Decker part number 905180165, follow these steps:
1. Remove the container from the appliance by pressing the two release buttons (31) and lifting the container out. 2. Take out the filter (35) from the container. 3. Brush off any loose dust from the filter.
Reassemble by replacing the filter and reinserting the container into the appliance.
This answer is automatically generated
Anna Maria Russo
March 23, 2025
How to open and clean the filter
1 comments:
Mr. Anderson
March 23, 2025
To open and clean the filter for Black & Decker part number 905180165:
1. Unplug the appliance before performing any maintenance. 2. Remove the filter by pulling it off the filter holder. 3. Do not brush or use compressed air to clean the filter. 4. Rinse the outside of the filter with water if needed. 5. Do not wash the inside of the filter. 6. Allow the filter to dry for 24 hours before reinserting it. 7. Replace the filter after cleaning. 8. Re-fit the pre-filter and close the lower door before using the appliance again.
Intended use Your Black & Decker vacuum cleaner has been designed to vacuum dry substances. This product is intended for household use only. Safety instructions Warning! When using mains-powered appliances, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock, personal injury and material damage.
Page 7
Features This appliance includes some or all of the following features. 1. Hose 2. Container handle 3. Filter cleaning switch (not VN1800N) 4. On/off switch 5. Handle 6. Cord rewind button 7. Suction head 8. Wheels 9. Container 10. Extension tube 11.
Unwinding and rewinding the cord The cord rewind button (6) can be operated by hand or foot. Before use, pull a sufficient length of cord from the back of the appliance. After use, press the cord rewind button (6) to store the cord back into place.
Page 9
Note: The appliance is designed to prevent vacuuming during the filter cleaning cycle. If the vacuum is switched on during the filter cleaning cycle, the filter cleaning cycle will stop. Warning! Before performing any maintenance or cleaning on the appliance, unplug the appliance. Regularly clean the ventilation slots in your appliance using a soft brush or dry cloth.
Protecting the environment Should you find one day that your tool needs replacement, or if it is of no further use to you, think of the protection of the environment. Black & Decker repair agents will accept old Black & Decker tools and ensure that they are disposed of in an environmentally safe way.
Need help?
Do you have a question about the 905180165 and is the answer not in the manual?
Questions and answers
Unable to open lid (Fig. J) to remove and clean filter.
To open the lid on a Black & Decker 905180165 and remove and clean the filter, follow these steps:
1. Remove the container: Press the two release buttons (31) and lift the container (9) out of the appliance.
2. Open the lower door: Press the lower door latch (32) to release the dirt.
3. Remove the filter: Take out the filter (35) from the container.
4. Clean the filter: Brush any loose dust off the filter.
5. Replace the filter: After cleaning, reinsert the filter (35).
6. Reassemble the container: Re-insert the container into the appliance, ensuring it clicks into place.
This answer is automatically generated
Cannot open figure J to clean filter
To clean the filter, follow these steps:
1. Remove the container (9) from the appliance by pressing the two release buttons (31) and lifting it out.
2. Press the lower door latch (32) to release the dirt.
3. Remove the filter (35) as shown in figure L.
4. Brush any loose dust off the filter.
5. Replace the filter (35) and re-insert the container into the appliance.
Figure J is not mentioned in the context, so it is not required for cleaning the filter.
This answer is automatically generated
May I please have a drawing of what I should do? I,e, how to remove filter?
To remove the filter for Black & Decker part number 905180165, follow these steps:
1. Remove the container from the appliance by pressing the two release buttons (31) and lifting the container out.
2. Take out the filter (35) from the container.
3. Brush off any loose dust from the filter.
Reassemble by replacing the filter and reinserting the container into the appliance.
This answer is automatically generated
How to open and clean the filter
To open and clean the filter for Black & Decker part number 905180165:
1. Unplug the appliance before performing any maintenance.
2. Remove the filter by pulling it off the filter holder.
3. Do not brush or use compressed air to clean the filter.
4. Rinse the outside of the filter with water if needed.
5. Do not wash the inside of the filter.
6. Allow the filter to dry for 24 hours before reinserting it.
7. Replace the filter after cleaning.
8. Re-fit the pre-filter and close the lower door before using the appliance again.
This answer is automatically generated