Related Manuals for HUSABERG FE 450 USA 2009
Summary of Contents for HUSABERG FE 450 USA 2009
- Page 1 SETUP INSTRUCTIONS FE 450 EU FE 450 USA FE 570 EU FE 570 USA 2009 ART. NO. 3802016en...
- Page 3 HUSABERG accepts no liability for delivery options, deviations from illustrations and descriptions, as well as misprints and other errors.
-
Page 4: Means Of Representation
MEANS OF REPRESENTATION Symbols used The symbols used are explained in the following. Indicates an expected reaction (e.g. of a work step or a function). Indicates an unexpected reaction (e.g. of a work step or a function). Identifies a page reference (more information is provided on the specified page). Formats used The typographical and other formats used are explained in the following. - Page 5 SET‑UP Unpacking and setting up the vehicle – Remove the box and the plastic packaging. Info To avoid damaging the motorcycle during the setup, leave the protective film on the vehicle until you have finished. – Check the vehicle for transport damage. –...
- Page 6 SET‑UP – Position the brake line and wiring harness in brake line guide – Insert the distance bushings in the brake line guide. Position the fender with the brake line guide. – Mount and tighten the screws. Guideline Remaining screws, chassis 10 Nm (7.4 lbf ft) –...
-
Page 7: Installing The Front Wheel
WORK Removing the headlight mask with the headlight – Switch off all power consumers and the engine. – Open rubber band on the fork legs. – Tilt the headlight mask forward and detach it from nose – Disconnect connector ... -
Page 8: Installing The Engine Guard
WORK – Fully tighten screw Guideline Screw, fork stub 15 Nm (11.1 lbf ft) Installing the engine guard – Attach the engine guard on the frame at the rear and swing it up and forward. Mount and tighten screw ... -
Page 9: Setting Kilometers Or Miles
If the vehicle is not ridden for more than two weeks, we recommend trickle 100425-10 charging the battery with the HUSABERG battery charger. The battery is first charged completely and then maintained at this level over the subse- quent period. Thus, the battery is always fully charged when the vehicle is put into operation. -
Page 10: Setting The Clock
WORK – Press the button briefly and repeatedly until H appears at the bottom right of the display. – Press the button for 3 - 5 seconds. The Setup menu opens and the active functions are displayed. – Press the button repeatedly until the Km/h/Mph display flashes. - Page 11 WORK Closing the filler cap 3.11 – Replace the filler cap and turn clockwise until the release button locks in place. Info Run the fuel tank breather hose without kinks. 100360-10 Refueling 3.12 Danger Fire hazard Fuel can easily catch fire. –...
-
Page 12: Technical Data - Tightening Torques For Chassis
TECHNICAL DATA - TIGHTENING TORQUES FOR CHASSIS – Spoke nipple, front wheel M4.5 5 Nm (3.7 lbf ft) – Screw, battery terminal 3 Nm (2.2 lbf ft) – Screw, intake air temperature sensor 2 Nm (1.5 lbf ft) – Spoke nipple, rear wheel 5 Nm (3.7 lbf ft) –... - Page 13 SUBSTANCES Super unleaded (ROZ 95 / RON 95 / PON 91) According to – DIN EN 228 (ROZ 95 / RON 95 / PON 91)
-
Page 14: Auxiliary Substances
AUXILIARY SUBSTANCES Long-life grease Specification – ® HUSABERG recommends Motorex products. Supplier ® Motorex – Fett 2000... - Page 15 HUSABERG eine Division der KTM SMC AG Stallhofnerstraße 3 5230 Mattighofen, Austria www.husaberg.com *3802016en* 3802016en...