Rip curl Tidemaster Manual page 3

SCREW CROWN (if applicable)
To change the time settings, the screw crown of your watch must first be unscrewed, as follows...
1. Make sure your watch is completely dry;
2. Turn the crown counterclockwise/towards you (fig.1);
SCREW CROWN (if applicable)
3. With crown completely unscrewed (fig.2 ), it can be pulled out to set your watch.
To change the time settings, the screw crown of your watch must first be unscrewed, as follows...
4. After setting, push crown back in fully, then carefully screw the crown in slowly to reseal your watch
1. Make sure your watch is completely dry;
(fig.3). Never force the screw.
2. Turn the crown counterclockwise/towards you (fig.1);
3. With crown completely unscrewed (fig.2 ), it can be pulled out to set your watch.
4. After setting, push crown back in fully, then carefully screw the crown in slowly to reseal your watch
(fig.3). Never force the screw.
For your watch to be properly sealed, the crown must be fully screwed in.
Note: Not all Tide watches have screw in crowns.
Never unscrew the crown when your watch is in water or is wet.
SETTING PROCEDURE
Time setting
For your watch to be properly sealed, the crown must be fully screwed in.
Unscrew the crown as shown above then pull crown out to the 2
Never unscrew the crown when your watch is in water or is wet.
in fully, then carefully screw the crown in slowly to reseal your watch (fig.3). Never force the screw.
SETTING PROCEDURE
Date setting
Time setting
Unscrew the crown as shown above then pull crown out to the 1
Unscrew the crown as shown above then pull crown out to the 2
set date, then push crown back to normal position, push crown back in fully, then carefully screw the crown in
in fully, then carefully screw the crown in slowly to reseal your watch (fig.3). Never force the screw.
slowly to reseal your watch (fig.3). Never force the screw.
Date setting
NOTE: The calendar will not move back by turning the crown counter-clockwise.
Unscrew the crown as shown above then pull crown out to the 1
NOTE: Do not set the date calendar between 9:00p.m. and 1:00a.m. Otherwise, it may not change properly.
set date, then push crown back to normal position, push crown back in fully, then carefully screw the crown in
It is necessary to adjust the date on the first day after a 30-day month and February.
slowly to reseal your watch (fig.3). Never force the screw.
SETTING THE TIDE FUNCTION - CENTRAL HAND
NOTE: The calendar will not move back by turning the crown counter-clockwise.
The tide cycle takes place over one revolution of the dial in 12 hours 25 minutes and 14 seconds. High tide
NOTE: Do not set the date calendar between 9:00p.m. and 1:00a.m. Otherwise, it may not change properly.
corresponds to the "12 o'clock" position and low tide corresponds to the opposite position, hence "6 o'clock".
It is necessary to adjust the date on the first day after a 30-day month and February.
You need to score a tide chart from your local surf shop (or newspaper) to initially set the Tide Height
SETTING THE TIDE FUNCTION - CENTRAL HAND
hand...
The tide cycle takes place over one revolution of the dial in 12 hours 25 minutes and 14 seconds. High tide
From your tide chart calculate the tide height right now. Tides are generally six hours apart. If your chart says
corresponds to the "12 o'clock" position and low tide corresponds to the opposite position, hence "6 o'clock".
high tide is three hours from now, set your watch to - mid tide, rising.
You need to score a tide chart from your local surf shop (or newspaper) to initially set the Tide Height
hand...
From your tide chart calculate the tide height right now. Tides are generally six hours apart. If your chart says
high tide is three hours from now, set your watch to - mid tide, rising.
ANALOGUE TIDEMASTER
ANALOGUE TIDEMASTER
Tide range
and Moon
phase dial
Tide range
Hour hand
and Moon
phase dial
Tide hand
Hour hand
Tide hand
UNSCREW
CROWN
UNSCREW
fig.1 fig.2
CROWN
IMPORTANT!
fig.1 fig.2
IMPORTANT!
Small second hand
Minute hand
Button A:
Small second hand
Tide range and Moon
phase setting
Minute hand
SCREW Crown
Button A:
Tide range and Moon
Button B:
phase setting
Tide cycle setting
SCREW Crown
Date
Button B:
Tide cycle setting
Date
ALIGN THREAD
CAREFULLY
& RESCREW
CROWN FULLY
BUT SLOWLY
ALIGN THREAD
CAREFULLY
fig.3 & RESCREW
CROWN FULLY
BUT SLOWLY
fig.3
nd
click position, change the time, push crown back
st click position. Turn the crown clockwise to
nd
click position, change the time, push crown back
st click position. Turn the crown clockwise to
11
11
3