Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for BenQ W2700
Summary of Contents for BenQ W2700
- Page 1 W2700/ HT3550 Projector RS232 Command Control Installation Guide...
-
Page 2: Table Of Contents
Table of Contents Introduction ............................. 3 Wire arrangement ................................ 3 RS232 pin assignment ..............................3 Connections and communication settings ..................4 RS232 serial port with a crossover cable ....................... 4 Settings .................................. 4 RS232 via LAN ................................6 Settings .................................. 6 RS232 via HDBaseT .............................. -
Page 3: Introduction
Introduction The document describes how to control your BenQ projector via RS232 from a computer. Follow the procedures to complete the connection and settings first, and refer to the command table for RS232 commands. Available functions and commands vary by model. Check the specifications and user manual of the purchased projector for product functions. -
Page 4: Connections And Communication Settings
Connections and communication settings Choose one of the connections and set up properly before RS232 control. RS232 serial port with a crossover cable D-Sub 9 pin (male) on a projector PC or laptop D-Sub 9 pin (female) Communication cable (crossover) Settings On-screen images in this document are for reference only. - Page 5 Choose Serial and the corresponding COM port as the communication port. In this given example, COM6 is selected. Finish Serial port setup. Baud rate 9600 bps Data length 8 bit Parity check None Stop bit 1 bit Flow control None...
-
Page 6: Rs232 Via Lan
RS232 via LAN RJ45 port on a projector PC or laptop LAN cable Settings Find the Wired LAN IP address of the connected projector from the OSD menu and make sure the projector and the computer are within the same network. Input 8000 in the TCP port # field. - Page 7 Finish Serial port setup. Baud rate 9600 bps Data length 8 bit Parity check None Stop bit 1 bit Flow control None...
-
Page 8: Command Table
Command table Available features differ by projector specification, input sources, settings, etc.. Commands are working if the standby power is 0.5W or a supported baud rate of the projector is set. Uppercase, lowercase, and a mixture of both types of characters are accepted for a command. ... - Page 9 Write Volume level for customer <CR>*vol=value#<CR> Read Volume Status <CR>*vol=?#<CR> Write Mic. Volume + <CR>*micvol=+#<CR> Write Mic. Volume - <CR>*micvol=-#<CR> Read Mic. Volume Status <CR>*micvol=?#<CR> Write Audio pass Through off <CR>*audiosour=off#<CR> Write Audio-Computer1 <CR>*audiosour=RGB#<CR> Write Audio-Computer2 <CR>*audiosour=RGB2#<CR> Audio source Write Audio-Video/S-Video <CR>*audiosour=vid#<CR>...
- Page 10 Write Tint - <CR>*tint=-#<CR> Write Set Tint value <CR>*tint=value#<CR> Read Get Tint value <CR>*tint=?#<CR> Write Sharpness + <CR>*sharp=+#<CR> Write Sharpness - <CR>*sharp=-#<CR> Write Set Sharpness value <CR>*sharp=value#<CR> Read Sharpness value <CR>*sharp=?#<CR> Write Flesh Tone + <CR>*fleshtone=+#<CR> Write Flesh Tone - <CR>*fleshtone=-#<CR>...
- Page 11 Read Brilliant color status <CR>*BC=?#<CR> Write Projector Position-Front <CR>*pp=FT#<CR> Table Write Projector Position-Rear <CR>*pp=RE#<CR> Table Write Projector Position-Rear <CR>*pp=RC#<CR> Ceiling Write Projector Position-Front <CR>*pp=FC#<CR> Ceiling Write Quick cooling on <CR>*qcool=on<CR> Write Quick cooling off <CR>*qcool=off<CR> Read Quick cooling status <CR>*qcool=?<CR> Write Quick auto search <CR>*QAS=on#<CR>...
- Page 12 Read Standby Settings-Monitor <CR>*standbymnt=?#<CR> Out Status Write 2400 <CR>*baud=2400#<CR> Write 4800 <CR>*baud=4800#<CR> Write 9600 <CR>*baud=9600#<CR> Write 14400 <CR>*baud=14400#<CR> Baud Rate Write 19200 <CR>*baud=19200#<CR> Write 38400 <CR>*baud=38400#<CR> Write 57600 <CR>*baud=57600#<CR> Write 115200 <CR>*baud=115200#<CR> Read Current Baud Rate <CR>*baud=?#<CR> Read Lamp Hour <CR>*ltim=?#<CR>...
- Page 13 Read Freeze Status <CR>*freeze=?#<CR> Write Menu On <CR>*menu=on#<CR> Write Menu Off <CR>*menu=off#<CR> Write <CR>*up#<CR> Write Down <CR>*down#<CR> Write Right <CR>*right#<CR> Write Left <CR>*left#<CR> Write Enter <CR>*enter#<CR> Write 3D Sync Off <CR>*3d=off#<CR> Write 3D Auto <CR>*3d=auto#<CR> Write 3D Sync Top Bottom <CR>*3d=tb#<CR>...
- Page 14 Read Broadcasting Status <CR>*broadcasting=?<CR> Write AMX Device Discovery-on <CR>*amxdd=on#<CR> Write AMX Device Discovery-off <CR>*amxdd=off#<CR> Read AMX Device Discovery <CR>*amxdd=?#<CR> Status Read Mac Address <CR>*macaddr=?#<CR> Write High Altitude mode on <CR>*Highaltitude=on#<CR> Write High Altitude mode off <CR>*Highaltitude=off#<CR> Read High Altitude mode status <CR>*Highaltitude=?#<CR>...
- Page 15 Color Write Tint - <CR>*tint=-#<CR> Calibration Write Set Tint value <CR>*tint=value#<CR> Read Get Tint value <CR>*tint=?#<CR> Write Set BenQ gamma value <CR>*gamma=value#<CR> Read Gamma value status <CR>*gamma=?#<CR> Write Set HDR Brightness value <CR>*hdrbri=value#<CR> Read Get HDR Brightness value <CR>*hdibri=?#<CR> Write Red Gain + <CR>*RGain=+#<CR>...
- Page 16 Write Set Blue Offset value <CR>*BOffset=value#<CR> Read Get Blue Offset value <CR>*BOffset=?#<CR> Write Primary Color <CR>*primcr=value#<CR> Read Primary Color Status <CR>*primcr=?#<CR> Write Hue + <CR>*hue=+#<CR> Write Hue - <CR>*hue=-#<CR> Write Set Hue value <CR>*hue=value#<CR> Read Get Hue value <CR>*hue=?#<CR> Write Saturation + <CR>*saturation =+#<CR>...
- Page 17 BenQ.com © 2018 BenQ Corporation All rights reserved. Rights of modification reserved. Version: 1.01-C...
Need help?
Do you have a question about the W2700 and is the answer not in the manual?
Questions and answers