Download
Share
Print this page
Honeywell NOTIFIER ASY-01-044-NIM Product Installation Sheet
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Control Unit
  5. NOTIFIER ASY-01-044-NIM
  6. Product installation sheet
Honeywell NOTIFIER ASY-01-044-NIM Product Installation Sheet

Honeywell NOTIFIER ASY-01-044-NIM Product Installation Sheet

Interface module
Hide thumbs
1
2
3
4
5
6

Advertisement

Quick Links

Download this manual
1 Product Overview
This Installation sheet describes how to mount and connect:
A Network Interface Module (NIM) to a Fire Panel
The Network Interface Module stores data received from the Networks Cards. The stored data is accessed by the
AFP-2800 and presented to the operator.
NOTE: The Network Card is supplied separately.
WARNING: Remove all power sources to equipment while connecting the components.
Leave the external, main power breaker OFF until installation of the components are
complete.
2 Installation
1. Unplug from the PSI board:
a. The 27 Volt PSU Power Supply Cable running from the PSI board - see Connection Schematic.
b. The 4 - Way Power Cable running from the Termination board - see Connection Schematic.
c. The Battery Power Supply - see Connection Schematic.
d. The 10 - Way Ribbon Cable running to the Termination board - see Connection Schematic.
PH 02-9894-1444 • FAX 02-9894-4193
ASY-01-044 - NIM
Product Installation Sheet
9 Columbia Way
Baulkham Hills, NSW 2153
www.notifier.com
1.00
28/06/2012 Rev:
DOC-03-061
ECN12-0032
1

Advertisement

loading

Related Manuals for Honeywell NOTIFIER ASY-01-044-NIM

Summary of Contents for Honeywell NOTIFIER ASY-01-044-NIM

  • Page 1 9 Columbia Way Baulkham Hills, NSW 2153 PH 02-9894-1444 • FAX 02-9894-4193 www.notifier.com ASY-01-044 - NIM Product Installation Sheet 1.00 28/06/2012 Rev: DOC-03-061 ECN12-0032 1 Product Overview This Installation sheet describes how to mount and connect:  A Network Interface Module (NIM) to a Fire Panel The Network Interface Module stores data received from the Networks Cards.
  • Page 2 2. Remove the 4 M3 x 8mm screws connecting the PSI mounting bracket to the Loop Interface Module (LIM) Figure 2-1: Removal of the M3 x 30mm Spacers, and the M3 x 20mm Spacers NOTE: Do not remove the M3 Screws connecting the PSI Mounting Bracket to the PSI board.
  • Page 3 3. Replace the existing M3 x 20mm Spacers and the M3 x 30mm Spacers with 4 M3 x 25mm Spacers (#11171) Figure 2-2: Mounting NIM to LIM with M3 x 25mm Spacers 4. Replace the 40 - Way Ribbon Cable connected to the LIM ‘IN’ Port with the 100mm 40 - Way Ribbon Cable (#10202) - see Connection Schematic.
  • Page 4 10. Position the PSI board assembly over the M3 x 25mm Spacers (#11171) and the M3 x 15mm Spacers (#11828) 11. Secure the PSI mounting bracket to the bottom Spacers with 2 M3 x 8mm Screws (#2316) 12. Screw the top part of the PSI board to the top spacers with 2 M3 x 8mm Screws (#2316) Figure 2-3: Mounting PSI board to NIM...

  • Page 5: Connection Schematic

    3 Connection Schematic Figure 3-1: NIM, LIM and PSI Schematic...

  • Page 6: Supplemental Documentation

    Components Part No. Description Screw Sems - Pan Philip Zinc, M3 X 8mm w/Flat Small 2316 S/Washer 10200 Cable-Assembly, C24 - 40 Way X 440mm 10202 Cable-Assembly, C26 - 40 Way X 100mm 10206 Cable-Assembly, C30 - 3 Way X 330mm 11171 M3 tapped spacer x 25mm - M/F, hexagonal, nickel finish 11628...