Konica Minolta GBC PUNCH G2 Operation & Instruction Manual page 12

PUNCH G2 Die Sets
The PUNCH G2 uses a variety of easily interchangeable die sets that allow you to punch documents in line for several different binding styles. By
selecting the appropriate die set, you can use your PUNCH G2 to punch documents in any of the following binding styles. Heavy Duty (HD) die sets
are shown in bold where available.
Die Set Description
For Plastic Comb Binding:
1
PB Plastic Bind; Hole Size: 8mm x 2.9mm (0.313" x 0.116") (LxW); Center-to-Center Hole Spacing: 14.3mm (0.563")
For Twin Loop™ Binding:
1
W3 Wire; Square; 3 Holes per inch; Hole Size: 4mm x 4mm (0.156" x 0.156") (L x W); Center-to-Center Hole Spacing:
8.5mm (0.333")
1
W2 Wire; Rectangle; 2 Holes per inch; Hole Size: 6.4mm x 5.4mm (0.250" x 0.214")(L xW); Center-to-Center Hole Spacing:
12.7mm (0.500")
1
W3 Wire; Round; 3 Holes per inch; Hole Size: 4mm (0.158") Diameter; Center-to-Center Hole Spacing: 8.5mm (0.335")
1
W2 Wire; Round; 2 Holes per inch; Hole Size: 6.5mm (0.0.256") Diameter; Center-to-Center Hole Spacing: 12.7mm (0.5")
For Color Coil™ Binding:
1
C4 Coil; Round; 4 Holes per inch; Hole Size: 4.4mm (0.174") Diameter; Center-to-Center Hole Spacing: 6.3mm (0.2475")
1
C4 Coil; Oval; 4 Holes per inch; Hole Size: 4mm x 5mm (0.158" x 0.197") (L x W); Center-to-Center Hole Spacing: 6.3mm
(0.2475")
®
For Velo Bind:
1
VB Velobind ® ; Round; 1 Hole per inch Hole Size: 3.2mm (0.125") Diameter; Center-to-Center Hole Spacing: 25.4mm (1")
1
VB Velobind ® ; Round; 1 Hole per inch Hole Size: 3.2mm (0.126") Diameter; Center-to-Center Hole Spacing: 25.4mm (1")
For Loose Leaf Binding:
1
3 Ring Binder; U.S. (Standard Loose-leaf Patterns); Hole Size: 8mm (0.316") Diameter
1
3 Ring, 5 Ring, 7 Ring; U.S. (Standard Loose-leaf Patterns); Hole Size: 8mm (0.316") Diameter
1
4 Ring Binder; European (Standard Loose-leaf Patterns); Hole Size: 8mm (0.315") Diameter
1
4 Ring Binder; European (Standard Loose-leaf Patterns); Hole Size: 6.5mm (0.256") Diameter
4 Ring Binder; Scandinavian (Standard Loose-leaf Patterns); Hole Size: 6.5mm (0.256") Diameter
©2016 GBC, Lake Zurich, Illinois - All rights reserved.
* When the Plastic Comb binding die is used in the 21 hole configuration on A4 width paper (297mm), there is the potential for the outer edge of holes 1 and 21 to
be torn. The theoretical paper edge should be 1.62mm from the edge of the sheet. This event is dependent on paper type, paper width and hole alignment
optimization. To avoid this issue, it is recommended to use a 20 hole configuration instead. 20 hole comb binding supplies are commonly available from GBC and
other manufacturers and are considered more optimal than the 21 hole configuration.
19-LTR 21-A4
32-LTR 34-A4
21-LTR 23-A4
32-L TR 34-A4
21-LTR 23-A4
44-LTR 47-A4
44-LTR 47-A4
11
12
3
7
4 4
4
Graphics do not represent actual punch pattern dimensions or spacing.
Part Number
Die, Konica Minolta, Comb Bind
Die, Konica Minolta, Comb Bind, HD
Die, Konica Minolta, Wire 3.1, Sq.
Die, Konica Minolta, Wire 2.1, Sq.
Die, Konica Minolta, Wire, 3:1, Rnd.
Die, Konica Minolta, Wire, 2:1, Rnd.
Die, Konica Minolta, Coil, Rnd.
Die, Konica Minolta, Coil, Rnd, HD
Die, Konica Minolta, Coil, Oval
®
Die, Konica Minolta, Velobind , 11 Holes, Ltr.
®
Die, Konica Minolta, Velobind , 12 Holes, A4.
Die, Konica Minolta, 3 Hole, 8mm
Die, Konica Minolta, 3 Hole, 8mm, HD
Die, Konica Minolta, 3/5/7 Hole, 8mm
Die, Konica Minolta, 4 Hole, 8mm
Die, Konica Minolta, 4 Hole, 6.5mm
Die, Konica Minolta, 4 Hole, Scan
PUNCH G2
EN
7714911
7714913
7714912
7714903
7714902
7714901
7714917
7714914
7714909
7714910
7714904
7714918
7714905
7714906
7714907
7714908
12