Programming The Remote Control To Operate A Cable Converter Box, Satellite Receiver, Vcr, Dvd Player, Or Htib (Home Theater In A Box); Remote Control Codes - Toshiba 32A43 Owner's Manual

Programming the remote control to operate a cable converter box,
satellite receiver, VCR, DVD player, or HTIB (home theater in a box)
Your Toshiba TV remote control is preprogrammed to operate most Toshiba devices. To program your TV remote
control to operate a non-Toshiba device (or a Toshiba device that it is not preprogrammed to operate), follow the steps
below. For details on using the remote control to operate the device, see page 14.
RECALL
POWER
}
Channel
Numbers
Device Switch
Note:
Each time you change the batteries, you will need to reprogram the remote control.
Some newer VCRs respond to either of two codes. These VCRs have a switch labeled "VCR1/
VCR2." If your VCR has this kind of switch and does not respond to the codes for your VCR brand,
set the switch to the other position ("VCR1" or "VCR2") and reprogram the remote control.

Remote control codes

In some cases you may not be able to operate your device with the TV remote control. Your other device may use a code
that is not recognized by the TV remote control. If this happens, you will need to use the remote control provided with
the device.
General Instruments: 062,
Cable converter box
089, 096
ABC: 061, 062, 063, 082,
Hamlin: 093
084, 087, 091, 092,
Hitachi: 062, 095, 096
096, 098
Jasco: 097
Archer: 065, 092, 097, 099
Jerrold: 062, 069, 071,
Cableview: 064, 094
082, 086, 089, 091,
Century: 092
096
Citizen: 090, 092, 097
Magnavox: 072, 096
Contec: 083, 085, 086,
Memorex: 091, 092, 104
088, 093, 098
Multi Canal: 090
Diamond: 093
Novavision: 101
Eagle: 091
Panasonic: 081, 083, 085
GE: 061, 062
Philco: 087
Gemini: 069, 070, 094
1
In the remote control code table (below and on the next page), find
the code for your device. If more than one code is listed, try each one
separately until you find one that works.
2
Set the Device Switch to the type of device you are programming
the remote control to operate—CBL/SAT (for a cable converter box
or satellite receiver), VCR (for a VCR or TV/VCR combo), or DVD
(for a DVD player or HTIB [home theater in a box]).
3
While holding down RECALL, press the Channel Number buttons
to enter the 3-digit code for your device.
4
To test the code, turn on the device, point the remote control at it, and
press POWER.
–If the correct code was entered, the device will turn off.
–If the device does not respond, repeat steps 1–4 using another code.
–If the device does not respond to another code, you will need to use
the remote control that came with the device.
Note: In addition to POWER, confirm that all necessary keys on the TV
remote control operate your device. If some keys are not operational,
repeat the device code setup using another code (if other codes are
listed for your device). If, after trying all listed codes, the necessary keys
do not operate your device, use the device's original remote control.
5
Remember to set the Device Switch back to "TV" to control the TV.
6
For future reference, write down the code(s) you used:
DEVICE CODE
Philips: 066, 067, 068, Sears: 095
070, 072, 073, 074, Signature: 062
075, 091, 092 Signature 2000: 096
Pioneer: 076, 077 Sprucer: 081, 085
Proscan: 061, 062 Starcom: 069, 082, 087,
Radio Shack: 092, 097, 096, 103, 104
099 Stargate: 069, 090
RCA: 064, 081 Sylvania: 095, 100
Realistic: 065 TeleView: 090
Recoton: 102 Texscan: 100
Samsung: 077, 090 Tocom: 071, 084, 085
Scientific Atlanta: 063, U. S. Electronics: 087,
078, 079, 080, 088, 096, 098
098, 101, 105 United Cable: 082
12
DEVICE CODE
Universal: 065, 092, 097,
099, 102, 103
Wards: 096
Satellite receiver
Alphastar: 038, 059
Chaparral: 034
DISH Network: 057
Drake: 020, 040, 044, 046,
050, 053
Echostar: 018, 041, 051
Express Vu: 057
Fujitsu: 027
GE: 008, 009, 013