Related Manuals for NARGESA MC150B
Summary of Contents for NARGESA MC150B
- Page 1 SECTION BENDING MACHINE MC150B INSTRUCTIONS BOOK PRADA NARGESA, S.L Ctra. de Garrigàs a Sant Miquel s/n · 17476 Palau de Santa Eulàlia (Girona) SPAIN Tel. +34 972568085 · nargesa@nargesa.com · www.nargesa.com...
- Page 2 Thank you for choosing our machines www.nargesa.com...
-
Page 3: Table Of Contents
5.3. Positioning the base-plate ................... 6. WARNINGS ..........................6.1. Residual hazards ....................... 6.2. Counter-productive methods ..................6.3. Other recommendations ..................... 7. ASSEMBLY OF THE ROLLERS .................... 7.1. Bending capacity ......................8. OPTIONAL ACCESSORIES ....................TECHNICAL ANNEX MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 4: Machine Details
Figure 1. External dimensions of the MC150B bending machine 1.3. Description of the machine The MC150B bending machine is a machine specifically designed for bending profiles, the majority of which are metal, with different thicknesses and configurations, such as solid profiles, pipes, T-profiles, an- gles... -
Page 5: Machine Part Identification
Horizontal support of back stand Anchor point Upper roller adjustment spindle Bending rollers Roller guides deformation adjustment Top roller - smooth Lower rollers - knurling Box door Upper housing Terminals cover Electrical panel Back supports (Horizontal) MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 6: General Characteristics
3 phased 230/400 V or 1 phased 230 V Intensity 3.5 / 2 A Type of pull Two rollers Roller speed 6 r.p.m. Roll diameter 127 mm Axes useful length 74 mm Structure material Plate Total weight 270 Kg Dimensions 690x943x1140 mm MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 7: Description Of The Guards
Although the major mobile elements are protected by the upper cover, it is necessary to take special precautions during bending operations in order to avoid entrapment between the rollers and the piece being bent. Figure 3. Mechanism protection guards MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 8: Transport And Storage
The design of the section bending machine MC150B allows the chassis inside the bench to reduce its volume when transported. Picture 5 shows this arrangement. -
Page 9: Storage Conditions
- Temperature of -25 °C to 55 °C or 75 °C for periods not exceeding 24hrs (remember that these temperatures are in storage conditions) - Machines or heavy objects should not be stacked on top MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 10: Maintenance
- You need to at least try minimum greasing on the inner walls through which the support of the upper roller moves. - Repeat the operation to ensure proper lubrication of all spindles and guides of the upper roller support. - Lubricate the machine on a regular basis according to its use. MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 11: Instalation And Start Up
It is advisable to work under the following atmospheric conditions: - Room temperature between +5 °C and +40 ºC without exceeding an average temperature of +35 °C within 24 hrs. - Humidity between 30% and 90% without water condensation . MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 12: Instructions For Connecting To The Power Supply
IMPORTANT: This machine must be connected to an electrical outlet with earthing contact. The pipes and section bending machine MC150B, is equipped with a three-phased motor 230V/400V 0.75kW and it’s ready to be connected to a three-phased 400V drive with earthing contact. - Page 13 On the contrary, in case of having a three-phased outlet 230V drive the engine-keeper at an intensity of "5A". If the engine-keeper installed can not be adjusted to the required intensity, it must be replaced by one with a higher amperage. Intensity regulator Figure 9. Adjust the intensity of the engine-keeper. MC150B BENDING MACHINE INSTRUCTION BOOK...
-
Page 14: Instructions For Use
- In the event of not obtaining the proper results, the position of the guide rollers for deformation must be adjust. - The roller mounting nuts must be tightened by manual force only . 5.2. Assembly of the rollers Figure 10. Position of the rollers in relation to the machine axes MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 15: Positioning The Base-Plate
Take the rear support off and fix with the screw and washer located on the top of the MC150B. Afterward, ensure the machine with a locking device. This device will link the crane cable with safety ring available on top of the section bending machine. -
Page 16: Warnings
6.2. Counter-productive methods Tools or rollers that are not supplied by the manufacturer of the machine, NARGESA S.L., and which have not been specially designed for the MC150B bending machine should never be used . 6.3. Other recommendations - Use gloves for handling the machine and during the bending processes. -
Page 17: Assembly Of The Rollers
Figure 12. Nomenclature of the rollers and assembly IMPORTANT NOTE: The clamping nut of the rollers should never be tightened with a wrench and only by hand. If pipe rollers are being used, the nuts must be loose. MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 18: Bending Capacity
50,8 x 3 63,5 x 3 63,5 x 3 76,2 x 2 101,6 x 3 = 2” x 3 = 2”1/2 x 3 =2”1/2 x 3 = 3” x 2 = 4” x 3 Optional rollers MC150B BENDING MACHINE INSTRUCTION BOOK... -
Page 19: Optional Accessories
In order to facilitate the bending of certain more delicate materials that require a very good surface finish or to facilitate the bending of more common sections, NARGESA has designed a series of rollers that can be purchased at an official dealership or by directly by contacting NARGESA S.L. -
Page 20: Technical Annex
Technical annex MC150B Bending Machine General Parts Diagram Electrical Panel Electric map MC150B BENDING MACHINE INSTRUCTION BOOK... - Page 21 A1. General parts diagram MC150B BENDING MACHINE INSTRUCTION BOOK...
- Page 22 MC150B BENDING MACHINE INSTRUCTION BOOK...
- Page 23 MC150B BENDING MACHINE INSTRUCTION BOOK...
- Page 24 MC150B BENDING MACHINE INSTRUCTION BOOK...
- Page 25 MC150B BENDING MACHINE INSTRUCTION BOOK...
- Page 26 MC150B BENDING MACHINE INSTRUCTION BOOK...
- Page 27 A2. Electrical Panel Double switch Transformer Breaker Switch MC150B BENDING MACHINE INSTRUCTION BOOK...
- Page 28 A3. Electric map MC150B BENDING MACHINE INSTRUCTION BOOK...
- Page 29 3. Complete the form with your details and press Message Sent: confirms your data has been successfully sent to Prada Nargesa SL. Your machine has been registered and has a warranty of three years in total. Your request has been sent correctly. We will contact you right...
Need help?
Do you have a question about the MC150B and is the answer not in the manual?
Questions and answers