Advertisement
tI fI tf X
WT
thermostat
user manuar
t4loel2ot6
art. no.:52008
Operating modes
The
electric heating device features
two operating
modes:
1.
Direct
Control
mode. The display shows
the
numeric value
of the
set
temperature.
2.
Edit
mode.
The
user
may
choose
a
pre-set weekly
heating
programme
from the list.
ln
the
Edit mode,
the
display shows
the
values
for
the weekly
heating programmes (see "The heater (not)
connected
to WiFf').
Turning on
the
Edit mode
ln
the
Direct
Control mode (when
the
display shows
the
numerical value
of
the
set
temperature), briefly
press
the
OK
button.
When
the
Edit mode
is
on,
the
display
will
show
the currently
set
value
of the
programme list.
Turning on
the
Direct Control mode
ïhe
heater
is
always
operating
ín
the
Direct Control mode-
lfyou
press
the
OK
button in the
Edit mode and
leave
the
device inactive
for
30
seconds,
the
heater
wili
automatically
switch
to the
Direct
Control
mode, and
the
display
wili show
the
numeric value of the
temperature that
was
set
the
last
time.
Edit mode menu
if
connected
to
WiFi
lf
the
heater is
connected
to
your home network and
the
Edit
mode
is
selected,
the
display
will
show
the
Iist
of weekly
heating programmes which
were configured
using
the Smart heater mobile
app.
lf
you
have
not
used
the Smart heater mobile app
or
have
not
created the
weekly heating programmes
in the
app,
the following
programme list
will
be
displayed:
r
HO
-
weekly heating programme "Home"
'
Ot
-
weekly heating programme "Office"
r
,1
-,,-
standby mode
.
AF
-
anti-freezing
temperature (default setting:7
"C).
lf the
user
has
created
new
weekly
heating programmes,
they
will
be shown
in
the iist
(unless
the
user
has set
otherwise):
r
P1, P2... -
weekly heating programmes.
A
preferred programme is selected
by
pressíng
the button "+"
or
"-"
and
confirmed
by briefly pressing the
OK
button.
Note:
if
the
preíerred programme
is
displayed,
but
the
OK
button is
not
pressed,
after
30
seconds
of
being idle, the heoter
will return to the
Direct
Control mode, ond will
mointain
the temperoture
thot
wos
set
previously.
lf
unable
to
connect
to your
home
network
(WiFi)
lf you cannot connect
the
heater
to
the
Internet,
you
will not
be
able
to
set
a
weekly heating
programme,
because
the current time
will
not
be set.
ln this
case,
the list of available functions in
the
Edit
mode
will
be
the
following:
o
HO
-
20
"C
temperature
is
maintained
.
AF
- anti-freezing
temperature (default
setting:
7'C).
r
"- -"
-
standby mode.
A
preferred programme is selected
by
pressing
the
button
'+" or
u-'
and
conÍirmed
by briefly
pressing
the
OK
button.
Note:
ií
the
preferred progromme
is
displayed,
but
the
OK
button
is
not
pressed,
ofter
j0
seconds
of
being idle, the hedter
will
return
to
the Direct
Control mode, ond utill
mointain
the temperoture
thot
was
set
previously.
Smart
conf
iguration
settings
When
the
user
starts
using
the
heater's mobile application,
the
user must
be
able
to
add
the
active heater
to
the application. which
is
configured according
to the
user's
needs. To
that
end,
press
and hold both
the buttons
simultaneously
until the
"SC"
(Smart Configuration) symbol
is
displayed.
Then
release
the
buttons.
The
SC
symbol
wiil
be
shown on the
screen
until the
heater
is
paired
with
the Smart Heater app.
After
the
configuration
is
completed (when
the
app
has
detected
the
heater),
both
indicators (blue
and red)
will
blink on
the
display. lf
the
app fails
to
detect
the
heating device
during the
configuration
process,
the
app
will
show
an
error
message
(for
nrore
information about
pairing
the
heater
to
the Smart Heater app,
see
the
Smart Heater app user manual at:
http://smartdevices.adax.lt/guides/en-
sma
rt-heater-user-ma
nua
l-
1.0.pdí
Regardless
of whether the configuration
has
been successíul
or not, after
30
seconds
oÍ
being idle,
the
heater
will
switch
from the
SC
mode
to
the
prevÍously
set
heating mode.
Temporary cancelling
(overriding) of defined
heating parameters
lf you
want to temporarily
stop
the
heating programme when
the
heater
is
in
the
Direct Control mode,
use
the "+"
or "-"
buttons
to
set
the
preferred
temperature.
Note:
in
the temporory temperature setting, the heoter
will
operate
until
o
new
heoting mode
storts
occording
to
the
weekly
heoting
progromme
schedule.
Resetting
the heater
lf
necessary,
the
user may restore
the default
settings.
To
that
end,
press
the
keys
"+",
simultaneously
until
"rE" flashes on
the
display. Then,
after
you release all
three buttons, the
d'splay
will
soon show 20
"C,
just
as
it
did the
first time
you
turned the
heater on.
Smart Heater app
www.adax.no
Fl
Available
on
the
U
App Store
Download Írom
Windows
Store
pöö$.pruy
Advertisement
