H3C S7500E Series Installation, Quick Start
Hide thumbs
Also See for S7500E Series:
- Command manual (1565 pages) ,
- Operation manual (1344 pages) ,
- Command reference manual (368 pages)
Related Manuals for H3C S7500E Series
Summary of Contents for H3C S7500E Series
- Page 1 H3C S7500E Switch Series Installation Quick Start New H3C Technologies Co., Ltd. http://www.h3c.com.hk Document version: 6PW102-20170430...
- Page 2 Copyright © 2015-2017, New H3C Technologies Co., Ltd. and its licensors All rights reserved No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of New H3C Technologies Co., Ltd.
-
Page 3: Table Of Contents
Contents Installation quick start ·················································································································································· 1 Chassis views and technical specifications ···················································································································· 1 Chassis views ···························································································································································· 1 Technical specifications ··········································································································································· 2 Safety recommendations ·················································································································································· 4 Examining the installation site ········································································································································· 5 Installing the switch ··························································································································································· 5 ... -
Page 4: Installation Quick Start
This installation quick start provides basic instructions for installing an S7500E switch. For more information about the installation procedure, see H3C S7500E Switch Series Installation Guide. The installation procedure is similar for all S7500E switch models. This installation quick start uses the S7503E switch as an example. -
Page 5: Technical Specifications
Figure 2 S7503E switch front panel (1) MPU slots (2) LPU slots (3) Power module slots (4) Fan tray slot Technical specifications Table 1 Chassis dimensions Model Height Width Depth S7502E 175 mm (6.89 in) (4 RU) 436 mm (17.17 in) 420 mm (16.54 in) S7503-S 175 mm (6.89 in) (4 RU) - Page 6 Maximum output Maximum PoE Model Rated voltage range Support for PoE power output power 100 VAC to 240 VAC @ PSR650C-12A 650 W 50/60Hz PSR650C-12D –48 VDC to –60 VDC 650 W 1150 W (110 VAC) 100 VAC to 240 VAC @ PSR1400-A 50/60Hz 1400 W (220...
-
Page 7: Safety Recommendations
Chassis Power module S7503E S7503 S7506E S7506E S7506E S7510 S7502E S7506E (non-PoE) PSR6000-ACV — — — NOTE: • " " indicates that the power module can be directly installed on the chassis. " " indicates that you must first install a power module adapter on the chassis and then install the power •... -
Page 8: Examining The Installation Site
The switch can only be used indoors. To make sure the switch operates correctly and prolong its service lifetime, the installation site must meet the requirements for load-bearing, temperature, humidity, cleanness, EMI, grounding power module, ventilation, and space. For more information, see H3C S7500E Switch Series Installation Guide. -
Page 9: Installing Cage Nuts
Figure 5 Installing a cage nut Align the installation holes on the front end of a slide rail with the cage nuts on a front rack post, and use six screws to attach the slide rail to the front rack post. Figure 6 uses the right slide rail as an example. - Page 10 Figure 7 Cage nut installation holes (1) Cage nuts Figure 8 Marking the cage nut installation holes Install the cage nuts.
-
Page 11: Installing Mounting Brackets And Cable Management Brackets
Installing mounting brackets and cable management brackets Installing the cable management brackets on the S7506E-V The S7506E-V has two cable management brackets: the one with a tray is installed at the lower part of the switch, and the one without a tray is installed at the upper part of the switch. They are installed in the same way. -
Page 12: Installing The Switch In The Rack
Installing the switch in the rack Follow these guidelines when you install the switch in the rack: To avoid equipment damage or bodily injury, use a minimum of two people to lift the switch. H3C • recommends that you use a mechanical lift to move the switch. -
Page 13: Grounding The Switch
Do not hold the filler panels, filler panel handles, or the air vents of chassis to carry the chassis. Any • attempt to carry the switch with these parts might cause equipment damage or even bodily injury. After placing the switch on the slide rails, do not leave go of your hands immediately because this •... -
Page 14: Installing Frus
Figure 13 Grounding the switch Installing FRUs Installing a card IMPORTANT: • Before installing a card in the chassis, make sure the connectors on the card are not broken or blocked. To ensure good ventilation, install a blank filler panel in an empty slot. •... -
Page 15: Installing A Power Module
Figure 14 Installing a card Installing a power module CAUTION: Provide a circuit breaker for each power module and make sure the circuit breaker is off before • installation. Do not install power modules of different models on the same switch. •... - Page 16 Figure 15 Installing a power module...
-
Page 17: Connecting Power Cords
Connecting power cords Connecting the PSR320-A/PSR650-A power cord Figure 16 Connecting the PSR320-A/PSR650-A power cord Connecting the PSR650C-12A power cord Figure 17 Connecting the PSR650C-12A power cord... - Page 18 Connecting the PSR1400-A power cord Figure 18 Connecting the PSR1400-A power cord Connecting the PSR2800-ACV power cord The PSR2800-ACV is a built-in power module with AC input and DC output. It provides one system power socket and one PoE power socket. The methods for connecting the system power cord and PoE power cord are similar to connecting the PSR1400-A power cord.
- Page 19 Figure 19 Attaching the power cord retainer suite (1) Screw holes for connecting the retainer suite to the power module (2) Power cord plug (3) Screw holes for connecting the two parts of the retainer suite Insert the power cord into the power socket on the power module, and fasten the power cord retainer suite to the power module.
- Page 20 Connecting the PSR320-D/PSR650-D/PSR650C-12D power cord Figure 21 Connecting the PSR320-D/PSR650-D/PSR650C-12D power cord Connecting the PSR1400-D/PSR1400-12D1 power cord Figure 22 Connecting the PSR1400-D/PSR1400-12D1 power cord...
-
Page 21: Accessing The Switch For The First Time
Accessing the switch for the first time Connecting the console cable The first time you access the switch you must use a console cable to connect a console terminal, for example, a PC, to the console port or USB console port on the switch. If both the console port and USB console port are connected to terminals, you can only access the switch through the USB console port. -
Page 22: Powering On The Switch
Verify that the LEDs on the switch are in the states as described Table 5. For more information about the LEDs, see H3C S7500E Switch Series Installation Guide. Table 5 LED status when the switching is operating correctly Item Model... -
Page 23: Obtaining Documentation
Steady green PoE IN3 Steady green PoE OUT Steady green PoE FAN Steady green Obtaining documentation Take the following steps to get related documents from the H3C website at www.h3c.com.hk. Go to http://www.h3c.com.hk/Technical_Documents. Choose the desired product category and model. -
Page 24: Index
Index A C E I O S Accessing the switch for the first time,18 Installing the switch,5 Chassis views and technical specifications,1 Obtaining documentation,20 Examining the installation site,5 Safety recommendations,4...