Table of Contents
Advertisement
Quick Links
Your Guide to the Installation,
You're Guide to the Installation, Care and maintenance of
PERFORMA
T555 and T555L Dual Control
T555 and T555L Dual Control
Dual Control Thermostatic
Thermostatic Bath and Shower Mixer
Thermostatic Bath and Shower Mixer
Bath and Shower Mixer
T555 Dual Control Thermostatic Bath and Shower Mixer - 329500
T555L (Lever) Dual Control Thermostatic Bath and Shower Mixer - 329501
T555 Dual Control Thermostatic Bath and Shower Mixer – 329500
Care and maintenance of
PERFORMA
Advertisement
Table of Contents
Related Manuals for Pegler Yorkshire PERFORMA T555
Summary of Contents for Pegler Yorkshire PERFORMA T555
- Page 1 Your Guide to the Installation, Care and maintenance of You’re Guide to the Installation, Care and maintenance of u’re Guide to the Installation, Care and maintenance of PERFORMA PERFORMA T555 and T555L Dual Control T555 and T555L Dual Control Dual Control Thermostatic Thermostatic Bath and Shower Mixer Thermostatic Bath and Shower Mixer Bath and Shower Mixer...
-
Page 2: Table Of Contents
Contents Introduction ......................3 Product Identification and Spares ............... 3 Water Regulation Requirements ................4 Pipe Connections ....................4 Water Supply Pressures ..................4 Condition of normal use ..................5 Product Specification ..................5 Pre-Installation Checks ..................5 Flow Regulator Specification ................6 Installation ...................... -
Page 3: Introduction
Before installing this product - Pegler Yorkshire recommend the reading of this Introduction document thoroughly and leaving it with the user for future reference. Before installing this product – Pegler Yorkshire recommend that you read this document thoroughly and leave it with the user for future reference. Product Identification and Spares... -
Page 4: Water Regulation Requirements
Water Regulations Requirements It is important to ensure that the water supplies to your taps and mixers are connected in accordance with the water regulations (WRAS) requirements and good plumbing practice. It is Pegler Yorkshires recommendation and good plumbing practice that the supplies of hot and cold water to the products should be at equal (balanced) pressures in order to provide a consistent flow. -
Page 5: Condition Of Normal Use
Minimum Temperature (Hot/Mixed) = 10ºC Difference Conditions for normal use Conditions for normal use This Pegler Yorkshire product has been designed to function under the following conditions suitable for use as a type Conditions for normal use 2 valve This Pegler Yorkshire product has been designed to function under the following conditions suitable for use as a type... -
Page 6: Flow Regulator Specification
Mixer. Refer to the Francis Pegler luxury showers brochure for a Outlet Connections comprehensive choice of “Waterfall” shower kits. A hose retaining ring is supplied with many Pegler Yorkshire slider The outlet for the shower is ”... -
Page 7: Outlet Connections
“Waterfall” shower kits. A hose retaining ring is supplied with many Pegler Yorkshire slider rail kits, ensuring that the handset cannot be dropped and submerged in water creating a possible back syphonage problem. See Bylaw 17 (2) B. -
Page 8: In Service Testing
The Dual control Thermostatic Bath and Shower Mixer works exceptionally well when fitted onto high pressure systems. Offering a flow rate of over 45 litres per minute at 2.5 bar (balanced pressures). However for installations of this nature and above Pegler Yorkshire recommend the installation of a flow regulator fitted to the outlet end of the product – which will help with the performance of the cold water safety shut failure. -
Page 9: Maintenance
BOTH sides hot and cold water to be turned off. Once tool is turn off water supply. BOTH sides hot and cold water to be turned off. Once tool is locat located rotate until stop is reached. (Pegler Yorkshire recommend hot side first) reached. (Pegler Yorkshire recommend hot side first) 4. -
Page 10: Mixed Water Temperature
hen the components have been cleaned thoroughly, reassemble as found (the filter and retaining 3. When the components have been cleaned thoroughly, reassemble as found (the filter and retaining ring should be pressed on until solid and square to the rest of the service valve inner ould be pressed on until solid and square to the rest of the service valve inner body). - Page 11 isolation test), then this is acceptable providing the temperature of the water seeping from the valve is no more than C above the designated maximum mixed water outlet temperature setting of the valve. IMPORTANT: 46°C is the maximum water temperature from the bath tap. The temperature takes account of the The following set of tests should be carried out allowable temperature tolerances inherent in thermostatic mixing valves and temperature losses in metal baths It is not a safe bathing temperature for adults or children.
-
Page 12: Disassemble For Cleaning
3. Using service valve tool (provided), locate in the castellation and rotate clockwise to turn off both supplied of water. Rotate until stop is reached. (Pegler Yorkshire recommend hot side first) 4. At this point the Bath and Shower Mixer has been isolated of water 5. - Page 13 16. Once removed the parts can now been cleaned or left to soak. Descale using limescale remover, spanner warm water or similar. 17. Examine all seals and replace if necessary; maintenance kits are available from Pegler Yorkshire IMPORTANT: Make sure the grooves of the pliers / spanner or similar hold both pillars technical.
-
Page 14: Reassembly Of Cartridge
Reassembly of Cartridge 1. Make sure the valve body is kept upright, with the splined bore at the top during reassembly. 2. Insert the spring 3. Insert the element support disc; making sure the step is facing downwards and locates in the inner diameter of the spring IMPORTANT: Do not get any grease on the element! If you do, make sure it is cleaned off thoroughly before replacing into the valve body! Any... -
Page 15: Care And Maintenance
Pegler Yorkshire products are manufactured to the highest of bleach. Pegler Yorkshire products are manufactured to the highest of standards and should require little or no standards and should require little or no maintenance. - Page 16 West Yorkshire, LS10 1RT, England. All brand names and logo styles are registered trademarks. LUXURY TAP SOLUTIONS Maintaining a policy of continual product development, Pegler Yorkshire reserves the right to change specifications, design and materials of products listed in this publication without prior notice.
Need help?
Do you have a question about the PERFORMA T555 and is the answer not in the manual?
Questions and answers