Table of Contents
Advertisement
Quick Links
P/N 126807-01 REV. E 01/2019
P126807-01
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
This appliance may be installed in an aftermarket permanently located, manufactured (mobile) home, where
not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases.
WARNING: This appliance is for installation only in a solid-fuel burning masonry or UL127 factory-built fi replace
or in a listed ventless fi rebox enclosure. It is design-certifi ed for these installations in accordance with ANSI
Z21.11.2. Exception: DO NOT install this appliance in a factory-built fi replace that includes instructions stating
it has not been tested or should not be used with unvented gas logs.
This is an unvented gas-fi red heater. It uses air (oxygen) from the room in which it is installed. Provisions for
adequate combustion and ventilation air must be provided. Refer to Air for Combustion and Ventilation section
on Page 6 of this manual.
WARNING: If the information in this manual is not followed exactly, a fi re or explosion may result
causing property damage, personal injury or loss of life.
– Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other
appliance.
– WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fi re department.
– Installation and service must be performed by a qualifi ed installer, service agency or the gas supplier.
Models
PFS
®
US
Report No. F10-087
Installation and Operation Instructions
Unvented (Vent-Free) Gas Log Heater
MAGNIFLAME24MN
MAGNIFLAME24VN
MAGNIFLAME24MP
MAGNIFLAME24VP
For use with log sets
SOUTHERNCOMFORT24A/B
SOUTHERNCOMFORT30A/B
SOUTHERNCOMFORT36A/B
MAGNIFLAME30MN
MAGNIFLAME30VN
MAGNIFLAME30MP
MAGNIFLAME30VP
SHADYHOLLOW24A/B
SHADYHOLLOW30A/B
SHADYHOLLOW36A/B
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Astria Fireplaces MAGNIFLAME24MN
Summary of Contents for Astria Fireplaces MAGNIFLAME24MN
- Page 1 Installation and Operation Instructions Unvented (Vent-Free) Gas Log Heater Models MAGNIFLAME24MN P/N 126807-01 REV. E 01/2019 MAGNIFLAME30MN MAGNIFLAME24VN MAGNIFLAME30VN ® MAGNIFLAME24MP MAGNIFLAME30MP MAGNIFLAME24VP MAGNIFLAME30VP Report No. F10-087 P126807-01 For use with log sets SOUTHERNCOMFORT24A/B SHADYHOLLOW24A/B SOUTHERNCOMFORT30A/B SHADYHOLLOW30A/B SOUTHERNCOMFORT36A/B SHADYHOLLOW36A/B INSTALLER: Leave this manual with the appliance.
-
Page 2: Table Of Contents
Thank you for your purchase. We appreciate your TABLE OF CONTENTS business! Safety ....................2 Please carefully read and follow all instructions in this manual. Pay Product Identifi cation ..............5 special attention to all warnings and safety information. Local Codes .................. 5 Following these safety, care, and operation instructions will help Optional Remote Control Accessories ........... - Page 3 SAFETY Continued DANGER: Carbon monoxide poisoning may lead WARNING: Young children should be carefully to death! supervised when they are in the same room with the appliance. When using the hand-held remote acces- Carbon Monoxide Poisoning: Early signs of carbon monoxide sory, keep selector switch in the OFF position to prevent poisoning resemble the fl...
- Page 4 SAFETY Continued fresh air is not available. See Air for Combus- 1. WARNING: This appliance is only for use tion and Ventilation, Page 6. If appliance keeps with the type of gas indicated on the rating shutting off, see Troubleshooting, Page 32. plate.
-
Page 5: Product Identifi Cation
PRODUCT IDENTIFICATION Left Side Right Side Chassis Control Knob Glowing Embers Flame Adjustment Knob Front Figure 1 - Product Identifi cation LOCAL CODES UNPACKING 1. Remove log set assembly from carton. Install and use appliance with care. The installation NOTE: Do not pick up appliance base assembly by must conform with local codes or in the absence of local codes, to the latest edition of The National burners. -
Page 6: Product Features
PRODUCT FEATURES OPERATION SAFETY DEVICE This appliance is clean burning. It requires no outside This appliance has a pilot with an Oxygen Depletion venting. There is no heat loss out a vent or up a Sensing (ODS) safety shutoff system. The ODS/ chimney. - Page 7 AIR FOR COMBUSTION AND VENTILATION Continued Vent-free fi replace ____________ Btu/Hr is less than 50 cubic feet per 1,000 Btu/hr (4.8 m per kw) of the aggregate input rating of all appli- Gas water heater* ____________ Btu/Hr ances installed in that space and an unconfi ned Gas furnace ____________ Btu/Hr space as a space whose volume is not less than...
-
Page 8: Installation
AIR FOR COMBUSTION AND VENTILATION Continued VENTILATION AIR Ventilation Air From Outdoors Provide extra fresh air by using ventilation grills Ventilation Air From Inside Building or ducts. You must provide two permanent open- This fresh air would come from an adjoining un- ings: one within 12"... - Page 9 INSTALLATION CHECK GAS TYPE Use the correct type of gas (natural or propane/LP). Continued If your gas supply is not the correct gas type, do not install appliance. Call the dealer where you purchased WARNING: Before installing in a the appliance for proper type appliance. solid fuel-burning fi...
- Page 10 INSTALLATION Continued NOTE: When installing your gas logs into a Noncombustible Requirements for Safe manufactured fi rebox, follow fi rebox manufac- Material Distance Installation turer’s instructions for minimum clearances to combustible materials. 12" or more Noncombustible material B. Clearances from the top of the fi replace opening to the ceiling should not be less than 42".
- Page 11 INSTALLATION Continued MANTEL CLEARANCES NOTICE: Surface temperatures of adjacent In addition to meeting noncombustible material walls and mantels become hot during clearances, you must also meet required clearances operation. Walls and mantels above the between fi replace opening and mantel shelf. If you fi...
- Page 12 INSTALLATION Continued INSTALLING DAMPER CLAMP ACCESSORY Damper Clamp FOR VENTED OPERATION NOTE: When used as a vented appliance, appli- Damper ance must be installed only in a solid-fuel-burning fi replace with a working fl ue and constructed of Damper noncombustible material. Clamp For Massachusetts Residents Only: Installation of this gas log set as a vented appliance in the...
- Page 13 INSTALLATION Continued Masonry Screw Installation Items Needed • hardware package (provided with appliance) • approved fl exible gas hose and fi ttings provided (if allowed by local codes) • sealant (resistant to propane/LP gas, not pro- vided) • electric drill with 3/16” masonry drill bit NOTE: Install optional MRC Series receiver and hand-held remote control kit (see Accessories, Page 40) before installing gas log appliance.
- Page 14 INSTALLATION Continued Apply pipe joint sealant lightly to male NPT threads. CAUTION: Use only new, black This will prevent excess sealant from going into pipe. Excess sealant in pipe could result in clogged iron or steel pipe. Internally-tinned appliance valves. copper tubing may be used in certain Propane/LP areas.
- Page 15 INSTALLATION Continued 3. Pressurize supply piping system by either CAUTION: Avoid damage to gas opening propane/LP supply tank valve for propane/LP gas or opening main gas valve control. Hold gas control with wrench located on or near gas meter for natural gas when connecting it to gas piping and/ or using compressed air.
- Page 16 INSTALLATION Continued Equipment Shutoff Valve Connect the wires to the valve from the switch assembly as shown in Figure 18. INSTALLING OPTIONAL REMOTE Gas Meter ACCESSORIES (REMOTE READY MODELS) Installing Remote Receiver Remote control accessories are available separately (see Accessories, Page 40). Read instructions shipped with remote control along with instructions Control Valve below before attempting installation.
- Page 17 INSTALLATION Continued 9. If logs were removed from appliance for install remote accessory, replace logs (see Installing Logs, Embers and Volcanic Stone, Page 18). 10. Place remote receiver on fi replace fl oor next to control valve. Make sure the remote receiver and wires are not on or touching either gas burner on the log set.
- Page 18 Refractory Concrete Logs For Burner System Model Use With This Burner System 2. Find the back left log SouthernComfort24A/B or ShadyHollow24A/B m o d e l s : D - 0 6 0 , MAGNIFLAME24MN SOUTHERNCOMFORT24A/B SouthernComfort30A/B or ShadyHollow30A/B MAGNIFLAME24VN SOUTHERNCOMFORT30A/B...
- Page 19 INSTALLATION Continued Vertical Portion of Burner Tube Figure 24C - Installing Right Front Log, Side Figure 25B - Installing Back Left Log View (D-018) Rear View Figure 25B shows how the notch in log fi ts against the vertical portion of the burner tube. The bottom of this log has a slot that fi...
- Page 20 INSTALLATION Continued Square Grate Log Notch Grate Finger Log Slot Figure 27B - Installing Charred Log Top Side Figure 26B - Installing Front Left Log View 5. Find the middle split log (SouthernComfort24A/B The left side of the burner tube fi ts into the or ShadyHollow24A/B models: D-063, notch on the back side of this log.
- Page 21 INSTALLATION Continued Back Top Log (D-062, Square Peg Right Split Crossover D-023 or D029) Right Split Cross- Log (D-022) over Log (D-022) Figure 31 - Installing Back Top Log and Final Right Front Log Assembly Figure 29 - Installing Right Split Crossover Log 7.
- Page 22 INSTALLATION Continued EMBER PLACEMENT WARNING: ALL PREVIOUSLY AP- Two ember materials are supplied with this log set. Platinum Bright Embers give a bright glow appear- PLIED LOOSE MATERIAL MUST BE RE- ing as hot coals. Should embers need replacing, see MOVED PRIOR TO REAPPLICATION.
-
Page 23: Operation
OPERATION REMOTE READY MODELS LIGHTING INSTRUCTIONS OPERATION FOR YOUR SAFETY WARNING: READ BEFORE LIGHTING • If fi replace has glass doors, never operate this appliance with glass WARNING: If you do not follow doors closed. If you operate appliance these instructions exactly, a fi re or with doors closed, heat buildup inside explosion may result causing property fi... - Page 24 REMOTE READY MODELS OPERATION Continued 6. Press in and turn control knob counterclock- NOTE: AUTO is only functional when using wise to the PILOT position. Press in GWMT1 or GWMS2 optional accessories. If control knob for fi ve (5) seconds (see Figure hand-held remote control is installed but not 35).
- Page 25 REMOTE READY MODELS NOTE: The burner may light if hand-held remote was on when selector switch was last turned off. OPERATION You can now turn burner on and off with hand-held Continued remote control unit. TO TURN OFF GAS IMPORTANT: Do not leave selector switch in the REMOTE or ON position when pilot is not lit.
- Page 26 VARIABLE REMOTE MODELS OPERATION Continued LIGHTING 7. With control knob pressed in, press and release igniter button. This will light pilot. The pilot is INSTRUCTIONS attached to the front burner. If needed, keep igniter button pressed in until pilot lights. NOTICE: During initial operation NOTE: If pilot does not stay lit, contact a quali- of new fi...
- Page 27 VARIABLE REMOTE MODELS OPERATION Continued Pilot HAND-HELD Burner REMOTE OPERATION BATTERIES WARNING: Make sure your selec- Igniter tor switch is in OFF position before Electrode installing or changing batteries in Figure 40 - Pilot (Natural/ Propane/LP) your hand-held remote or receiver. For installing or replacing batteries in remote con- TO TURN OFF GAS trol or receiver, see Installing Batteries in Remote...
- Page 28 VARIABLE REMOTE MODELS OPERATION Continued FLAME HEIGHT OPERATING REMOTE CONTROL This function allows you to control height of fl ames through 5 levels (see Figure 44). Select WARNING: Fireplace can turn on manual fl ame height function by pressing MODE suddenly.
-
Page 29: Inspecting Burners
VARIABLE REMOTE MODELS OPERATION Continued To activate this function, press THERMOSTAT but- INSPECTING BURNERS ton until the word SMART appears to the right of Check pilot fl ame pattern and burner fl ame pat- temperature bulb graphic on display. Use UP/DOWN terns often. -
Page 30: Cleaning And Maintenance
CLEANING AND MAINTENANCE 5. Blow air into the primary air holes on the injec- WARNING: Turn off appliance and tor holder. 6. In case any large clumps of dust have now been let cool before cleaning. pushed into the burner repeat steps 3 and 4. Clean pilot assembly also. -
Page 31: Specifi Cations
SPECIFICATIONS MAGNIFLAME24MN MAGNIFLAME24MP MAGNIFLAME24VP MAGNIFLAME24VN MAGNIFLAME30MP MAGNIFLAME30MN MAGNIFLAME30VP MAGNIFLAME30VN • Rating (Variable): 29,000/40,000 Btu/Hr • Rating (Variable): 29,000/40,000 Btu/Hr • Type Gas: Propane/LP • Type Gas: Natural • Ignition: Electronic • Ignition: Electronic • Manifold Pressure: 7.9" W.C. • Manifold Pressure: 3.4" W.C. -
Page 32: Troubleshooting
TROUBLESHOOTING WARNING: Turn off appliance and let cool before servicing. Only a qualifi ed service person should service and repair heater. CAUTION: Never use a wire, needle or similar object to clean ODS/pilot. This can damage ODS/pilot unit. NOTE: All troubleshooting items are listed in order of operation. OBSERVED PROBLEM POSSIBLE CAUSE REMEDY... - Page 33 TROUBLESHOOTING Continued OBSERVED PROBLEM POSSIBLE CAUSE REMEDY ODS/pilot lights but fl ame goes 1. C o n t r o l k n o b n o t f u l l y 1. Press in control knob fully out when control knob is released pressed in 2.
- Page 34 TROUBLESHOOTING Continued OBSERVED PROBLEM POSSIBLE CAUSE REMEDY Yellow fl ame in front burner dur- 1. Not enough air 1. Check burner(s) for dirt ing burner combustion and debris. If found, clean burner(s) (see Cleaning and Maintenance, Page 30) 2. Replace gas regulator 2.
- Page 35 TROUBLESHOOTING Continued WARNING: If you smell gas • Shut off gas supply. • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.
-
Page 36: Parts
PARTS REMOTE-READY VARIABLE CONTROL MODELS MAGNIFLAME24MN, MAGNIFLAME24VN, MAGNIFLAME24MP, MAGNIFLAME24VP, MAGNIFLAME30MN, MAGNIFLAME30VN, MAGNIFLAME30MP AND MAGNIFLAME30VP Cat. No. Model F0076 MAGNIFLAME24MN F0077 MAGNIFLAME24VN F0079 MAGNIFLAME24MP F0080 MAGNIFLAME24VP F0082 MAGNIFLAME30MN F0083 MAGNIFLAME30VN F0085 MAGNIFLAME30MP F0086 MAGNIFLAME30VP WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifi... - Page 37 PARTS REMOTE-READY VARIABLE CONTROL MODELS MAGNIFLAME24MN, MAGNIFLAME24VN, MAGNIFLAME24MP, MAGNIFLAME24VP, MAGNIFLAME30MN, MAGNIFLAME30VN, MAGNIFLAME30MP AND MAGNIFLAME30VP This list contains replaceable parts used in your appliance. When ordering parts, follow the instructions listed under Replacement Parts on Page 40 of this manual. WARNING: Contact an IHP dealer to obtain any of these parts. Never use substitute materials not approved by IHP.
- Page 38 PARTS LOG SET MODELS SOUTHERNCOMFORT24A/B, SOUTHERNCOMFORT30A/B, SOUTHERNCOMFORT36A/B This list contains replaceable parts used in your appliance. When ordering parts, follow the instruc- tions listed under Replacement Parts on Page 40 of this manual. SOUTHERNCOMFORT24A/B SOUTHERNCOMFORT30A/B SOUTHERNCOMFORT36A/B CAT. NO. Log Id. # CAT.
- Page 39 PARTS LOG SET MODELS SHADYHOLLOW24A/B, SHADYHOLLOW30A/B AND SHADYHOLLOW36A/B This list contains replaceable parts used in your appliance. When ordering parts, follow the instruc- tions listed under Replacement Parts on Page 40 of this manual. SHADYHOLLOW36A/B SHADYHOLLOW24A/B SHADYHOLLOW30A/B CAT. NO. Log Id. # CAT.
-
Page 40: Replacement Parts
PARTS This list contains replaceable parts used in your appliance. When ordering parts, follow the instructions listed under Replacement Parts below. PARTS AVAILABLE, NOT SHOWN - ALL MODELS J3658 Warning Plate J3846 Lighting Instruction Plate J3664 Caution Decal J3689 Hardware Kit 80L42 Volcanic Stone J8174... - Page 41 ACCESSORIES Continued FIREPLACE HOOD, BLACK Cat No. F1764, Model GA6050 For all models. Helps deflect heat away from mantel or wall above fi replace. Fits openings 28" to 48" wide. VOLCANIC STONE Cat No. 80L42, Model FDVS For all models. Order when additional volcanic stone is desired.
- Page 42 ACCESSORIES Continued ON/OFF REMOTE AND RECEIVER WITH WHITE WALL PLATE GAS APPLIANCE INSTALLATION KIT Cat. No. F2236, Model RCKIT4001 Cat. No. F0249, Model CIKA For all Remote-Ready Models. Allows the fi replace to be turned on and off by using a hand-held remote control.
-
Page 43: Warranty
Innovative Hearth Products Astria ® Brand Gas Log Set & Outdoor Gas Fire Pit Limited Three Year Warranty THE WARRANTY Innovative Hearth Products Limited Three Year Warranty ("IHP") warrants your Astria ® brand Gas Log Set or Outdoor Gas Fire Pit ("Product") to be free from defects in materials and workmanship at the time of manufacture. - Page 44 Astria.us.com Record the following important information about your appliance: Appliance model number Appliance serial number Date appliance was Installed Type of gas appliance uses Dealer name Innovative Hearth Products (IHP) reserves the right to make changes at any time, without notice, in design, materials, specifi cations, prices and also to discontinue colors, styles and products.
Need help?
Do you have a question about the MAGNIFLAME24MN and is the answer not in the manual?
Questions and answers