Related Manuals for Harman REVEL PERFORMA Be4 F226Be
Summary of Contents for Harman REVEL PERFORMA Be4 F226Be
- Page 1 F226Be Loudspeaker Owner’s Manual Revel PerformaBe F226Be Loudspeaker_OM_V4.indd 1 8/29/2019 12:01:12 PM...
-
Page 2: Table Of Contents
IMPORTANT SAFETY INSTRUCTIONS electrical and electronic equipment consists of the crossed-out wheeled bin, as shown below. 1. Use only attachments/accessories specified by the manufacturer. 2. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. -
Page 3: Unpacking The F226Be
UNPACKING THE F226Be Unpack the F226Be in the order of the illustrations below. Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Step 10 Step 11 Revel PerformaBe F226Be Loudspeaker Owner’s Manual Revel PerformaBe F226Be Loudspeaker_OM_V4.indd 3 8/29/2019 12:01:12 PM... -
Page 4: About Revel Performabe Loudspeakers
ABOUT REVEL PERFORMABe LOUDSPEAKERS F226Be OVERVIEW FEATURE HIGHLIGHTS • Beryllium Dome Tweeter 1" Beryllium Dome • 5th-generation Acoustic Lens Waveguide Tweeter with Acoustic • Deep Ceramic Composite (DCC™) Cone Midrange and Woofers Lens Waveguide • Wide bandwidth and dynamic range with minimal dynamic compression •... -
Page 5: Loudspeaker Placement
To avoid this, anchor the loudspeaker to the floor and/ or wall using the same procedures and hardware used to anchor bookcases, wall units, and other furniture. HARMAN International Industries, Inc. assumes no responsibility for proper selection and installation of hardware or for any personal injuries or product damages resulting from improper installation or a fallen loudspeaker. -
Page 6: Making Connections
on each room boundary. These are reflection points that require acoustic treatment materials. If acoustic treatment materials are not available, hanging a rug over the reflection points will help reduce sonic degradation in overly “live” rooms. Carpeting the floor area between the loudspeakers and the primary listening position and placing irregular surfaces such as Binding Posts bookcases at the first reflection points will also help minimize strong reflections. -
Page 7: Bi-Wired Connections
To make single-wire connections: Preamp (one channel shown) 1. Connect one speaker cable to the desired set of F226Be input terminals. (The high- frequency – “HIGH” – input terminals are recommended.) Then connect the other end of that speaker cable to the desired power amplifier output channel. 2. -
Page 8: Optimizing Performance
Preamplifier Y-Adapter for Single Connector OUTPUT A OUTPUT B F226Be Connector Panel F226Be Connector Panel INPUT A INPUT B OUTPUT A OUTPUT B Two-Channel Amplifier Shorting Shorting Two-Channel Amplifier Straps Straps OUTPUT A OUTPUT B Removed Removed INPUT A INPUT B 1. -
Page 9: Caring For Your Loudspeakers
CARING FOR YOUR LOUDSPEAKERS LIMITED WARRANTY Revel loudspeakers are warranted against defects. The duration of a warranty depends on GRILLES the laws in the country in which it was purchased. Your local Revel retailer can help you Revel PerformaBe speakers feature grilles with a magnetic attachment method that determine the duration and coverage of your warranty. - Page 10 8500 Balboa Boulevard, Northridge, CA 91329 USA © 2019 HARMAN International Industries, Incorporated. All rights reserved. Revel and the Revel logo are trademarks of HARMAN International Industries, Incorporated, registered in the United States and/or other countries. All Rights Reserved. Features, specifications and appearance are subject to change without notice.