1. Manuals
  2. Brands
  3. Advantech Manuals
  4. DVR
  5. DMR2008
  6. Manual

Advantech DMR2008 Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Digital Video Recorder
DMR2008
1

Advertisement

Table of Contents
loading

Related Manuals for Advantech DMR2008

Summary of Contents for Advantech DMR2008

  • Page 1 Digital Video Recorder DMR2008...
  • Page 2 The description written in the manual may not be exactly the same because the device may be updated. Thank you for purchasing DMR2008. Please read this manual before using the device and keep it safely for your reference in the future. The appearance and the functionalities of the product as described in this manual can be changed in the future without advance notice.
  • Page 3 3. The product must be repaired at the place of purchase or approved A/S center 4. Do not place any container with liquid near or on top of the product. (If liquid comes into contact with the product and causes system malfunction, stop and turn off the product and call the place of purchase.) 5.

  • Page 4: Table Of Contents

    --CONTENTS— 1. INTRODUCTION 2. SYSTEM ORGANIZATION A. PARTS B. FRONT SECTION C. REAR SECTION D. INTERNAL STRUCTURE E. HDD INSTALLATION 3. INSTALLATION (CAMERA & MONITOR) 4. NETWORK CONNECTION 5. CONNECTING TO PC 6. REMOTE MONITORING 7. DVR108NSB MANAGEMENT 8. BASIC CONFIGURATION 9-1.
  • Page 5 Other areas that require security Main Features The stand-alone, non-pc type DMR2008 can provide all system function. Real-time monitoring and recording of up to 8 cameras are possible at the same time. (Real-time monitoring – 240 FPS / recording – 30 FPS) Motion can be automatically recorded through motion detection function.

  • Page 6: System Organization

    B. Front Section The front section of DMR2008 consists of the LED part which can display current system conditions and the key operation part which can operate the HDD Rack and DMR2008. The DMR2008 function keys can be divided into DM R2008 panel section and DMR2008 remote controller section.

  • Page 7: Rear Section

    C. Rear Section The rear section of DMR2008 consists of BNC Connector Input, 8ch Camera Input, TV-Out 2ch. In addition, there is LAN port, power plug and power switch. (WARNING: NETWORK FUNCTION CAN BE ADDED OR NOT DEPEND ON THE MODEL OF PRODUCTS.) D.
  • Page 8 [EX. SEAGATE 7200RPM product] Assemble the HDD disk to the HDD rack. Connect IDE cable to DMR2008. Installation is completed by locking the rack with the rack key. (To prevent loss or damage, locking with the key is necessary.)

  • Page 9: Installation (Camera & Monitor)

    [Power of on/off does not work when the remote controller is off.] Attention When the power of DVR2008 is abruptly cut off, it can cause malfunction of HDD and/or DMR2008 Always use the power switch of DMR2008 rear side or on the remote controller.

  • Page 10: Network Connection

    Internet via ADSL modem. Set the PPPoE IP Configure parameters and connect the cable. Depending on the type of the modem, DMR2008 may not be directly connected to the ADSL modem. In that case, the broadband router (additional purchase) may be needed between the model and DMR2008 for network connection.

  • Page 11: Remote Monitoring

    [However, when IP router is being used, fixed IP should be used and TCP (913,914,915) port should be opened] a. DMR2008 client mode : a multiple of DMR2008 can be connected to one IP router. However, TCP (913, 914, 915) port should be opened when IP router is being used.
  • Page 12 A. DVR108 Explorer Log in www.adamsecu.com and join the site as the member. Log in again after entering Mac address. The image will appear on the screen through DMR2008 Explorer by clicking Service. B. DMR2008 Manager Log in www.adamsecu.com as a member using the user ID and password.
  • Page 13 7. DMR2008 Operation The main display can show one channel, four channels, six channels, seven channels, and eight channels. When multiple channels are being recorded, indicates on the left upper corner, and it keeps showing the signal for one second when the record is done.

  • Page 14: Basic Configuration

    8. DVR108 Basic Configuration The main menu can be activated by pressing [MENU] button on the front section of DMR2008. (It is equivalent to [MENU] key on the remote controller.) Pressing [MENU] while at the Channel Monitor mode displays the following configuration menu.

  • Page 15: Picture Control

    Use [UP] or [DOWN] key to move among the menu items. Press [ENTER] or [MENU] to select the item to configure. 9.1 Recoding Mode In this mode, DMR2008 recording mode, recording frame, brightness and color tones can be changes. CONFIGURATION: controls the picture of the recorded image on the screen.

  • Page 16: Configuration

    This item is selected for continuous recording. There is a submenu. DMR2008 is only configured for Motion Detection as a factory default. The continuous recording can be configured by setting the frames for the item that has FRAME OFF for the continuous recording. (As the values of resolution and frame increase, total recording time will decrease.)

  • Page 17: Disk Status [Hdd Disk Information]

    - [CH1],[CH2],[CH3],[CH4] NOLMAL RECORDING , [CH1],[CH2],[CH3],[CH4] EVENT RECORDING PREVIEW : The screen quality with the configured parameters can be previewed. Using the DMR2008 memory, recording and replaying can be repeated. The currently available memory and recorded memory are displayed in the bar graph on the screen.

  • Page 18: Motion Detection

    - Model name of the hard disk: DMR2008 can automatically recognize the hard disk. The recognized hard disk model and the total storage capacity can be checked with the actual information. - Display of the record image for each channel in HOUR / MINUTE / SECOND: This time is calculated by the configured FRAME RATE parameter.

  • Page 19: Detected Area Editing

    A. Detected Area Editing - Motion Detection Area: The range can be set up in details. Up to 16 squares horizontally and 12 squares vertically (total of 192 grids) can be set up. Current square is displayed in orange while the selected detection area is displayed in green. - [LEFT], [RIGHT], [UP] and [DOWN]: These keys move the cursor location.

  • Page 20: Network Configuration

    DETECTED AREA EDITING and SENSITIVITY values are not changed. 9-4. Network Configuration This enables monitoring of recorded and current image remotely by connecting DMR2008 to the network. It shows the Internet registration parameters which can be modified in accordance with the current user network environment.

  • Page 21: Manual Ip Configuration

    - DVR2008 SERVER MODE : When DMR2008 is used as server. [IP should be based on private IP, TCP (913,914,915) PORT should be opened] a. DMR2008 client mode : a multiple of DMR2008 can be connected to one IP router. However, TCP (913,914,915) PORT of remote site should be opened.
  • Page 22 form the numeric keys on the remote controller. SETTING / EXIT: To maintain the current values, the [ENTER] or [MENU] key must be pressed. Enter User ID and password. For entering the user ID and password, the keys on the remote controller must be used. The numeric keys of the remote controller can also enter the alphabetic letters as follows: [1], [.], [Q], [Z] [2], [A], [B], [C]...

  • Page 23: Channel Switch Sequence

    9-5. Channel Switch Sequence The switching sequence and the interval time of QUAD and 8 channels can be configured while monitoring the DMR200 8screen. CH1, CH2, CH3, CH4, CH5, CH6, CH7, CH8, CH1-2-3-4-5-6, CH1-2-3-4-5-6-7, CH1-2-3-4-5-6-7-8 : Each display can be turned ON or OFF by selecting each item and then pressing the [ENTER] or [MENU] key. INTERVAL TIME: This determines the interval time for each display.

  • Page 24: Disk Test [Hdd Disk Test]

    UTILITY: In this menu, the installed disk can be initialized; the recorded image can be deleted; the parameters can be reset to the factory default values; the pass word can be changed; accurate time can be set; and the remote controller channels can be changed.
  • Page 25 C. FACTORY SETTING FACTORY SETTING: Selecting FACTORY SETTING after entering the password changes all DMR2008 parameters to the factory set default values. Attention: Password is also changed. D. PASSWORD CHANGE - PASSWORD CHANGE: The password can be changed. The password is a maximum 8 digit number starting with non-zero.
  • Page 26 EXIT / SETTING: To maintain the current values, the [ENTER] or [MENU] key must be pressed. F. Remote Controller When operating the multiple DMR2008’s, the channel of each DMR2008 can be assigned; enabling operation of up to 5 DVR108’s from one remote controller.

  • Page 27: Firmware Update

    OFF. [1], [2], [3], [4] and [5]: DMR2008 can be turned OFF using the [F1], [F2], [F3], [F4] or [F5] key on the remote controller. If [2] was set, the remote controller is turned OFF if any key other than [F2] is pressed. It is turned back ON when [F2] key is pressed.

  • Page 28: Product Information [Version Information]

    When network and firmware upgrade are ready, the following message will be shown. - CURRENT : it shows the current product version, and the server version. User should choose the version and enter the password. Enter the retry, and then the upgrade will be completed.

  • Page 29: Replay Channel Selection Menu

    HOUR: 0 ~ 23 (AM 12 is displayed as 0.) MINUTE: 0 ~ 59 SECOND: 0 ~ 59 When DMR2008 is first powered on, it is set as the last recorded time and then changed to the last replayed time.

  • Page 30: Specification

    So the appropriate replay time should be entered. If the replay display is started when the replay time is set as the last record time right after DMR2008 booting, it is automatically set to reverse replay since there is no more recorded data.
  • Page 31 ATA Adaptor 10M Ethernet (RTL8019) IR Receiver/9 Keys Video Encoder 1Ch (SAA7121) Multiplex ALOGICS AP-5200M x 2 SDRAM 16Mbytes x 4 Codec Analog-Device ADV611(full frame codec/ Wavelet) DRAM 512Kbytes Feature Video Input RCA (8 Channel) TV - Output RCA (2 Channel) Supports Motion Detect and Normal Recording Mode Universal input voltage range with NO range selection switches.

Table of Contents