No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. How- ever, Advantech Co., Ltd.
Technical Support and Assistance Visit the Advantech web site at www.advantech.com/support where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately. 1 x ARK-2151S unit 1 x Hard copy user manual (Simplified Chinese) ...
Remplacez uniquement par un type identique ou équivalent recom- mandé par le fabricant. Jetez les piles usagées selon les instructions du fabri- cant. ARK-2151S User Manual...
Page 6
(ex. screws) provided with the accessory box. ATTENTION: Tout composant non vérifiée pourrait causer des dommages inat- tendu. Pour garantir une installation correcte, s'il vous plaît utilisez toujours les composants( vis ex.) fournies avec la boîte d'accessories. ARK-2151S User Manual...
Chapter General Introduction This chapter gives background information on ARK-2151S series.
Page 8
Introduction ARK-2151S is an industrial grade dual core mobile device for outdoor NVR solution. ARK-2151S support Full-HD NVR solution for and is fully integrated certified hard- ware and intelligent management software design. Well-developed vehicle software SDK and APIs for surveillance applications. Also, extension capacity and wireless...
Take care in order to avoid injury or damage to the equipment. Installing Memory Need to remove total 9pcs screws and can install memory on the top side of board. (4pcs on top and 5pcs on side of top cover) ARK-2151S User Manual...
Remove 2.5" drive bay and Insert full size mSATA storage in marked place. Installing Optional Modules 2.4.1 Installing WLAN module Remove 6pcs screws on bottom cover. ARK-2151S User Manual...
Chapter Jumper and Switch Settings This chapter explains how to set up ARK-2151S Series hardware, including instructions on setting jumpers and connecting peripher- als, and how to set switches and read indicators. Be sure to read all the safety pre- cautions before beginning the installation procedure.
A pair of needle-nose pliers may be helpful when working with jumpers. If there are any doubts about the best hardware configuration for the application, contact the local distributor or sales representative before making any changes. An arrow is used on the motherboard to indicate the first pin of each jumper. ARK-2151S User Manual...
Table 3.1: Auto Power On Setting (J2) Setting Function Power Button for Power On (1-2)* Auto Power On (default) 3.3.1.2 LCD Power (J3) (1-3)* (3-5) (3-4) Table 3.2: LCD Power (J3) Setting Function (1-3)* +3.3 V (default) (3-5) +5 V (3-4) +12 V ARK-2151S User Manual...
Page 21
Some of mSATA or mPCIe modules can't be recognized correctly through the Auto Detect setting. Suggest to use mSATA or mPCIe setting directly if meet any compati- bility problem. 3.3.1.4 Clear CMOS (SW3) (1-2)* (2-3) Table 3.4: Clear CMOS (SW3) Setting Function (1-2)* Normal (2-3) Clear CMOS ARK-2151S User Manual...
ARK-2151S-S9A1E I/O Pin Definition 4.2.1 VGA Connector The ARK-2151S provides a high resolution VGA interface connected by a D-sub 15- pin connector to support a VGA CRT monitor. It supports display resolution of up to 1920 x 1200 with 60 Hz.
4.2.2 USB Connector The ARK-2151S provides up to four USB interface connectors - 2 x USB 2.0 & 2 x USB 3.0, which give complete Plug & Play. The USB interface is compliant with USB UHCI, Rev. 2.0 & 3.0. The USB interface supports Plug and Play, which enables you to connect or disconnect a device whenever you want, without turning off the com- puter.
DP_PWR 4.2.5 DIO Connector ARK-2151S offers an 8-bit phenix type DIO connector and two ground pin. 6 x DI & 2 x DO w/ 3 KV isolation. Connector Type: 10-pin screw terminal block (6 DI points, 2 DO points, GND) ...
4.2.6 Power Input Connector ARK-2151S comes with 3-pin phoenix type power input connector for 9 ~ 36 VDC input. Figure 4.6 Power Input Connector 4.2.7 Power Over Ethernet ARK-2151S-S9A1E provides 4 x 10/100 PoE ports. 4ports full-load, IEEE802.3af Class 2 (7 Watt) ...
4.2.8 System Audio Connector ARK-2151S offers stereo audio ports by a phone jack connector of Line-out, Mic-in & Line-in. The audio chip controller is by Realtek ALC888, High Definition Audio. Figure 4.8 System Audio Connector Table 4.6: Audio Connector Pin Assignments...
Figure 4.10 Reset 4.2.12 LED Indicator There are two LEDs on ARK-2151S front metal face plate for indicating system sta- tus: PWR LED is for power status; and SSD LED is for SSD flash disk status. Figure 4.11 LED Indicator...
Chapter BIOS settings This chapter introduces how to set BIOS configuration data.
Page 32
AMIBIOS has been integrated into many motherboards for over a decade. With the AMIBIOS Setup program, you can modify BIOS settings and control the various sys- tem features. This chapter describes the basic navigation of the ARK-2151S BIOS setup screens.
System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time must be entered in HH:MM:SS format. ARK-2151S User Manual...
Page 34
5.2.2 Advanced BIOS Features Setup Select the Advanced tab from the ARK-2151S setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the <Arrow>...
Page 35
This item allows users to enable or disable VGA Palette Snoop. PERR# Generation This item allows users to enable or disable PERR# Generation. SERR# Generation This item allows users to enable or disable SERR# Generation ARK-2151S User Manual...
Page 36
Link Training Timeout (uS) This item allows users to set the Link Training Timeout (uS). Unpopulated Links This item allows users to set the Unpopulated Links. Restore PCIE Registers Enable or disable Restore PCIE Registers. ARK-2151S User Manual...
Page 37
S3 Video Repost This item allows users to enable or disable VBIOS run after S3 resume. ACPI Low Power S0 Idle This item allows users to enable or disable system wake on alarm event by Items setting. ARK-2151S User Manual...
Page 38
5.2.2.4 Trusted Computing Figure 5.7 Trusted Computing Configuration Security Device Support Enable or disable BIOS support for security device. ARK-2151S User Manual...
Page 39
5.2.2.5 S5 RTC Wake Settings Figure 5.8 S5 RTC Wake Settings Wake system with fixed time Enable or disable system wake on alarm event. ARK-2151S User Manual...
Page 40
This item allows users to enable or disable intel’s virtualization technology. Hardware Prefetcher This item allows users to enable or disable the hardware prefetcher feature. Adjacent Cache Line Prefetch This item allows users to enable or disable the adjacent cache line prefetch fea- ture. ARK-2151S User Manual...
Page 41
This item allows users to enable or disable the Hot Plug. External SATA This item allows users to enable or disable the External SATA. SATA Device type This item allows users to select mode of SATA Device type. ARK-2151S User Manual...
Page 42
5.2.2.8 Intel® Rapid Start Technology Figure 5.11 Intel® Rapid Technology Intel® Rapid Start Technology This item allows users to enable or disable Rapid Start Technology, if supported. ARK-2151S User Manual...
Page 43
This item allows users to enable or disable Alert Specification Format. Activate Remote Assistance Process This item allows users to enable or disable trigger CIRA boot. USB Configure This item allows users to enable or disable USB configure function. ARK-2151S User Manual...
Page 44
OS Timer Set OS watchdog timer. BIOS Timer Set BIOS watchdog timer. 5.2.2.10 PCH-FW Configuration Figure 5.13 PCH-FW Configuration Firmware Update Configuration This item allows users to enable or disable ME FW image re-flash function. ARK-2151S User Manual...
Page 45
Set the maximum time of the device will take before it properly reports itself to the Host Controller. 'Auto' uses default value: for a Root port it is 100 ms, for a Hub port the delay is taken from Hub descriptor. ARK-2151S User Manual...
Page 46
EC Power Saving Mode This item allows users to set board's power saving mode when off. Backlight Mode This item allows users to set backlight Function. EC Watchdog Function This item allows users to select EC watchdog timer. ARK-2151S User Manual...
Page 47
5.2.2.13 Super IO Configuration Figure 5.16 Super IO Configuration Serial Port 1 Configuration This item allows users to configure serial port 1. Serial Port 2 Configuration This item allows users to configure serial port 2. ARK-2151S User Manual...
Page 48
Figure 5.17 Serial Port Console Redirection Console Redirection This item allows users to enable or disable console redirection for Microsoft Win- dows Emergency Management Services (EMS). Console Redirection This item allows users to configuration console redirection detail settings. ARK-2151S User Manual...
Page 49
5.2.3 Chipset Select the Chipset tab from the ARK-2151S setup screen to enter the Chipset BIOS Setup screen. You can display a Chipset BIOS Setup option by highlighting it using the <Arrow> keys. All Plug and Play BIOS Setup options are described in this sec- tion.
Page 50
5.2.3.1 System Agent (SA) Configuration Figure 5.19 System Agent (SA) Configuration VT-d This item allows users to enable or disable VT-d. ARK-2151S User Manual...
Page 51
This item allows users to select DVMT total memory size. – Panel Power Enable This item allows users to enable or disable Panel Power. Graphics Perfor- mance. – Analyzers This item allows users to enable or disable Graphics Performance Analyzers. ARK-2151S User Manual...
Page 52
LCD Control Figure 5.21 LCD Control Primary IGFX Boot Display Select boot display device at post stage. LVDS This item allows user to enable or disable LVDS. LCD Panel Type This item allows users to select panel resolution. ARK-2151S User Manual...
Page 53
Memory Configuration Figure 5.22 Memory Configuration – Memory Information This item shows memory configuration parameters. ARK-2151S User Manual...
Page 54
Enable or disable USB to wake the system from S4. SLP_S4 Assertion Width This item allows users to set a delay of sorts. Restore AC Power Loss This item allows users to select off, on and last state. ARK-2151S User Manual...
Page 55
Glitch W/A for bad USB device(s) connected behind PCIE/PEG Port. – Subtractive Decode This item allows users to enable or disable Subtractive Decode. – PCI Express Root Port 1/2/3/6 This item allows users to configure PCI Express Root port 1/2/3/6 setting. ARK-2151S User Manual...
Page 56
This item allows users to enable or disable trunk clock gating. – USB Ports Per-Port Disable Control This item allows users to enable or disable USB Ports Per-Port Disable Con- trol. Control each of the USB ports (0~13) disabling. ARK-2151S User Manual...
Page 57
Azalia This item allows users to change Azalia settings. – Control detection of the Azalia device Disable- Azalia will be unconditionally Disabled. Enabled- Azalia will be unconditionally Enabled. Auto- Azalia will be enabled if present, disabled otherwise. ARK-2151S User Manual...
Page 58
This item allows users to set the system boot order. Hard Drive BBS Priorities This item allows users to set the order of the legacy devices in this group. CSM Support This item allows users to enable or disable CSM support. ARK-2151S User Manual...
To access the sub menu for the following items, select the item and press <Enter>: Change Administrator / User Password: Select this option and press <ENTER> to access the sub menu, and then type in the password. ARK-2151S User Manual...
Restore Defaults The ARK-2151S automatically configures all setup items to optimal settings when users select this option. Optimal Defaults are designed for maximum sys- tem performance, but may not work best for all computer applications. In particu- lar, do not use the Optimal Defaults if the user's computer is experiencing system configuration problems.
Page 61
When users have completed system configuration, select this option to save changes as user defaults without exit BIOS setup menu. Restore User Defaults The users can select this option to restore user defaults. Boot Override This item allows users to choose boot device. ARK-2151S User Manual...