Sun Microsystems J4400 Replacement Manual
Storage array chassis
Hide thumbs
Also See for J4400:
- System overview manual (112 pages) ,
- Site preparation manual (36 pages) ,
- Replacement manual (12 pages)
Subscribe to Our Youtube Channel
Related Manuals for Sun Microsystems J4400
Summary of Contents for Sun Microsystems J4400
- Page 1 Sun Storage J4400 Array Chassis Replacement Guide Sun Microsystems, Inc. www.sun.com Part No. 820-4601-10 April 2008, Revision A Submit comments about this document at: http://www.sun.com/hwdocs/feedback...
- Page 2 Copyright 2008 Sun Microsystems, Inc., 4150 Network Circle, Santa Clara, Californie 95054, Etats-Unis. Tous droits réservés. Sun Microsystems, Inc. a les droits de propriété intellectuels relatants à la technologie qui est décrit dans ce document. En particulier, et sans la limitation, ces droits de propriété...
-
Page 3: Table Of Contents
Contents Replacing a J4400 Array Chassis 1 Prerequisites 1 Verifying a Chassis Failure 1 ESD Precautions 2 Removing a Chassis 2 Installing the New Chassis 9 Installing CRUs Into a New Chassis 11 Completing the Chassis Installation 14 Related Documentation 15... - Page 4 Sun Storage J4400 Array Chassis Replacement Guide • April 2008...
-
Page 5: Replacing A J4400 Array Chassis
Replacing a J4400 Array Chassis This document describes replacement procedures for the Sun Storage J4400 Array chassis. Caution – Only trained service personnel should remove the covers on this equipment. This product is intended for restricted access whereby access is controlled through... -
Page 6: Esd Precautions
Caution – You must remove power from the chassis that needs to be replaced before starting this procedure. All interconnected trays will be disrupted during this procedure. Powering off one J4400 Array tray causes loss of access to other interconnected trays. - Page 7 Grasp the metal body of the connector with one hand, and use your other hand to firmly grasp and pull the tab. b. Pull the tab gently toward the connector body, and, then with your other hand, extract the connector from the bulkhead. Replacing a J4400 Array Chassis...
- Page 8 (see FIGURE 2 b. Pull the power supply out of the tray. c. Place the power supply aside. Removing a Power Supply FIGURE 2 Sun Storage J4400 Array Chassis Replacement Guide • April 2008...
- Page 9 SIM board from the tray. b. Pull the SIM board from chassis (see FIGURE 3 c. Place the SIM board aside in a static-free environment. Removing a SIM Board From the Chassis FIGURE 3 Replacing a J4400 Array Chassis...
- Page 10 Grasp the middle of the disk drive and pull it toward you to remove it from the tray (see FIGURE 4 Removing a Disk Drive or Disk Filler Assembly FIGURE 4 Sun Storage J4400 Array Chassis Replacement Guide • April 2008...
- Page 11 Removing the System Locking Clips FIGURE 5 J4400 Tray Mounting Rail Locking Clip Locking Clip Installed b. From the front of the cabinet, loosen the four captive screws, two on either side of the tray. Replacing a J4400 Array Chassis...
- Page 12 FIGURE 6 Removing the Failed Chassis From the Cabinet FIGURE 6 d. Package the failed chassis and return it to Sun, if instructed to do so, or properly dispose of it. Sun Storage J4400 Array Chassis Replacement Guide • April 2008...
-
Page 13: Installing The New Chassis
(see FIGURE 7 Installing the New Chassis in the Cabinet FIGURE 7 2. Tighten the captive screws on each side of the tray front to secure the chassis to the cabinet. Replacing a J4400 Array Chassis... - Page 14 ). You can use a Phillips head screwdriver for leverage FIGURE 8 to help you push in the clip. Installing the System Locking Clips FIGURE 8 J4400 Tray Mounting Rail Locking Clip Locking Clip Installed Sun Storage J4400 Array Chassis Replacement Guide • April 2008...
-
Page 15: Installing Crus Into A New Chassis
Press the extraction lever closed until it snaps in place on the disk front panel to seat the drive into the tray. Installing the Disk Drives and Filler Assemblies in New Chassis FIGURE 9 Replacing a J4400 Array Chassis... - Page 16 Simultaneously push both extraction levers toward the middle of the board to seat it in the tray. d. Tighten the extraction lever captive screws to secure the board. Installing a SIM Board FIGURE 10 Sun Storage J4400 Array Chassis Replacement Guide • April 2008...
- Page 17 Simultaneously push both extraction levers toward the middle of the power supply to seat it in the tray. d. Tighten the extraction lever captive screws to secure the power supplies. Installing a Power Supply FIGURE 11 Replacing a J4400 Array Chassis...
-
Page 18: Completing The Chassis Installation
3. Turn on power to both power supplies. Reconnecting the Mini-SAS and Power Cables FIGURE 12 Power Cord Connection from Host Connection Between or SIM Link IN to Tray 0 and Tray 1 Management Host Sun Storage J4400 Array Chassis Replacement Guide • April 2008... -
Page 19: Related Documentation
If an alarm sounds after plugging in the first power cord, the alarm will shut off once the second power cord is connected. Related Documentation For additional information about the Sun Storage J4400 Array chassis, see the following product documentation: Application... - Page 20 Sun Storage J4200/J4400 Array Rail Kit 820-3764-nn procedures Installation Guide Service Contact Information If you need help installing or using this product in the United States, call 1-800-USA-4SUN(872-4786), or go to: http://www.sun.com/service/contacting/index.xml Sun Storage J4400 Array Chassis Replacement Guide • April 2008...
- Page 21 Replacing a J4400 Array Chassis...
Need help?
Do you have a question about the J4400 and is the answer not in the manual?
Questions and answers