Maintenance And Cleaning; Technical Data - Batavia BT-RS004 Operating Instructions Manual

English
Plunge cutting
11.1
• Plunge cutting may only be used on
soft materials such as wood, aerated
concrete, gypsum plaster boards, etc.
• However, this requires a certain practise
and is only possible with short saw
blades.
• Place the saw onto the workpiece and
switch it on.
• Ensure that the bottom edge of the
footplate rests on the workpiece
surface.
• Slowly saw into the workpiece at an
angle, moving the saw to a vertical
position and continue to saw along the
cutting line.
• Switch the saw off and lift off the work-
piece when the work is complete.
Flush sawing
11.2
• Elastic bi-metal saw blades allow you to
saw protruding objects (e,g, water pipes,
iron bars, etc,) nearby the wall.
• Apply the saw blade directly to the wall
and bend slightly so that the footplate
rests against the wall.
• Switch the machine on and saw off the
workpiece keeping constant lateral
pressure against the wall.

12. Maintenance and Cleaning

• Prior to all work on the reciprocating
saw, first disconnect the main power
plug.
• Keep the saw blade and the saw in a
good and clean condition in order to
work well and safely. Clean the device
of dust and sawdust only with a paint-
brush, cloth or brush. Keep the ventila-
tion openings (7) always clean.
• Never use gasoline or other harsh
chemicals or abrasives to avoid damag-
ing the reciprocating saw. Make sure
that no liquids get into the reciprocating
saw.
Checking and replacing the carbon
12.1
brushes
The carbon brushes must be checked regu-
larly. If the carbon brushes are worn, the
machine will start to run unevenly.
8
7062850-Reciprocating_Saw-Ma-1801-08.indb 8
Only use the correct type of carbon
brushes.
• Remove the carbon brush holders
(3) using a screwdriver.
• Clean the carbon brushes.
• In case of wear, replace both carbon
brushes at the same time.
• Mount the carbon brush holders (3)
using a screwdriver.
• After mounting the new carbon
brushes, let the machine run at no load
for 15 minutes.

13. Technical data

Nominal Voltage: . . . . . . . 230 V~ 50 Hz
Nominal Power: . . . . . . . . . . . . 1050 W
Stroke:. . . . . . . . . . . . . . 0 – 2500 min
Stroke Rate:. . . . . . . . . . . . . . . 28 mm
Length of Power Cord: . . . . . . . . . . 3 m
Weight: . . . . . . . . . . . . . . . . . . 3.4 kg
Sound Pressure Level (L
Uncertainty: . . . . . . . . . . . . K = 3 dB(A)
Sound Power Level (L
WA
Uncertainty: . . . . . . . . . . . . K = 3 dB(A)
Hand Arm Vibration:. . . . . . . . 25.65 m/s
Uncertainty: . . . . . . . . . . . K = 1.5 m/s
Degree of Protection: . . . . . . . . . . . IP20
Protection Class:. . . . . . . . . . . . . . . . II
Vibration level
13.1
The vibration emission level stated in this
instruction manual has been measured in
accordance with a standardised test given
in EN 60745; it may be used to compare one
tool with another and as a preliminary
assessment of exposure to vibration when
using the tool for the applications
mentioned
• using the tool for different applications,
or with different or poorly maintained
accessories, may significantly increase
the exposure level
• the times when the tool is switched off
or when it is running but not actually
doing the job, may significantly reduce
the exposure level
Protect yourself against the effects of vibra-
tion by maintaining the tool and its accesso-
ries, keeping your hands warm, and organiz-
ing your work patterns.
-1
): . . . 92.2 dB(A)
pA
): . . . . 103.2 dB(A)
2
2
19-03-18 11:09