Overview Purpose EVM Basic Functions Power Requirements 1.3.1 Voltage Limits EVM Operational Procedure Circuit Description Schematic Diagram Circuit Function 2.2.1 Analog Inputs 2.2.2 Power 2.2.3 Outputs Parts List Physical Description PCB Layout Schematics SLWU020B – February 2005 – Revised February 2006 Submit Documentation Feedback Contents Contents...
Page 4
Top Layer Layer 2, Ground Plane Layer 3, Power Plane #1 Layer 4, Power Plane #2 Layer 5, Ground Plane Layer 6, Bottom Layer Three Pin Jumper List Table Output Connector J9 Test Point Description Bill of Materials for EVM List of Figures List of Figures List of Tables...
EVM components. EVM Operational Procedure The EVM provides a flexible means of evaluating the ADS5423/24/33 or ADS5411 in a number of modes of operation. A basic setup procedure that can be used as a board confidence check is as follows: 1.
Page 6
EVM Operational Procedure JUMPER FUNCTION SJP3 Provides AIN+ source to ADC device SJP4 Provides AIN– source to ADC device 2. Connect supplies to the EVM as follows: +5 V (4.75 V–5.25 V) ADC analog supply to J3 and return to J2. +3.3 V (3 V–3.6 V) digital buffer supply to J4 and J1 and return to J6 3.
In this case, connect the 3.3 V to J1 and the return to J2. 2.2.3 Outputs The data outputs from the ADC are buffered using a Texas Instruments SN74AVC16244. Output data header J9 is a standard 40-pin header on a 100-mil grid, and allows easy connection to a logic analyzer.
Circuit Function J9 PIN TEST POINT Circuit Description Table 2-1. Output Connector J9 DESCRIPTION J9 PIN DATA BIT 0 (LSB) DATA BIT 1 DATA BIT 2 DATA BIT 3 DATA BIT 4 DATA BIT 5 Table 2-2. Test Point Description FUNCTION Monitor Vref (AVDD/2) Monitor DMID (DVDD/2)
Table 3-1 lists the parts used in constructing the EVM VALUE CAPACITORS 0.1 F, 25 V, +80/–20% Capacitor 0.01 F, 25 V, +80/–20% Capacitor 220 pF, 50 V, 5%, Capacitor 22 pF, 50 V, 5%, Capacitor 220 pF, 50 V, 5%, Capacitor 0.01 F,16 V, 10% Capacitor 0.1 F,16 V, 10% Capacitor 470 pF,50 V, 5% Capacitor...
Page 10
Table 3-1. Bill of Materials for EVM (continued) VALUE ADS5423/24/33 or ADS5411 SN74AVC16244 THS4503 THS4601 Surface Mount Jumper Location: SJP3 (2–1), SJP4 (2–3) Parts List PART NUMBER VENDOR ADS5423/24/33 or Texas Instruments ADS5411 SN74AVC16244DGG Texas Instruments THS4503 Texas Instruments THS4601 Texas Instruments SLWU020B –...
This chapter describes the physical characteristics and PCB layout of the EVM and lists the components used on the module. PCB Layout The EVM is constructed on a 6-layer, 4.77-inch individual layers are shown in SLWU020B – February 2005 – Revised February 2006 Submit Documentation Feedback SLWU020B –...
Page 22
Schematics EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use.
Page 23
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 It is important to operate this EVM within the AVDD voltage range of –0.3 V to 3.8 V and the DVDD voltage range of –0.3 V to 3.8 V.
TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers amplifier.ti.com...