Advertisement
Quick Links
where inspiration flows
Installation Guide
Thermostatic shower valve with adjustable rigid riser
VEL-149RRK-RO-CP
This instruction booklet covers model:
AQB-149RRK-RO-CP
VEL-149RRK-RO-CP
ATM-149RRK-RO-CP
AQB-149RRK-RO-CP
ATM-149RRK-RO-CP
Note: for illustrative purposes only the VEL model is shown.
Vado
Please follow the same procedure to install the AQB & ATM.
Wedmore Road, Cheddar, Somerset, England BS27 3EB
tel 01934 744466.
fax 01934 744345
aftersales@vado.com
www.vado.com
Keep for future reference
Version 1, 1-3-18
Advertisement
Related Manuals for VADO VEL-149RRK-RO-CP
Summary of Contents for VADO VEL-149RRK-RO-CP
- Page 1 Installation Guide Thermostatic shower valve with adjustable rigid riser VEL-149RRK-RO-CP This instruction booklet covers model: AQB-149RRK-RO-CP VEL-149RRK-RO-CP ATM-149RRK-RO-CP AQB-149RRK-RO-CP ATM-149RRK-RO-CP Note: for illustrative purposes only the VEL model is shown. Vado Please follow the same procedure to install the AQB & ATM.
-
Page 2: Table Of Contents
Contents Notes Important information ..........3 General installation ...........3 Operating Specifications ...........3 Contents of packaging ..........4 Dimensions ..............6 Installation - Quick guide ..........7 Installation - Off-set connectors ......12 Installation - Quick -fit connectors ......13 Installation - Shower hose ........17 Commissioning ............18... -
Page 3: Important Information
Commissioning Important - please read The valve has been factory set under balance pressures and hot water supply at 65°C. Please read these instructions carefully before starting installation and keep for When your specific operating conditions are significantly different from the above, the future reference. -
Page 4: Contents Of Packaging
Contents of Packaging Installation - Shower hose Shower head Make sure there is a rubber washer in Riser arm place in the shower head and screw onto Shower head the riser arm. Washer Installation guide & Handset User manual Valve Place one of the rubber washer into the cone end of the hose and screw to the handset. - Page 5 Installation - Riser rail Contents of Packaging Place the bracket against the wall. Make sure that the riser is vertical, mark the two fixing holes in the wall bracket with a pencil. Wall bracket Level Warning! Please check for any Wall bracket hidden cables and pipes before drilling holes in the wall.
-
Page 6: Dimensions
Dimensions Installation - Riser rail 400mm You can adjust the height of the riser to suit your requirements. Riser arm Carefully push the riser arm into the riser until you reach the required position. Cover Slide the securing nut down and into the riser, tighten the nut. -
Page 7: Installation - Quick Guide
Installation - Quick fit connectors Installation - Quick guide Slide on the olive, screw on and tighten the nut. Before installation flush through the pipe work to ensure removal of debris, turn off the water supply. Olive Covers Locking nuts 150mm Filter/washer Screw the covers on each offset connector. - Page 8 Installation - Quick guide Installation - Quick fit connectors Note: Make sure that the valve is positioned to allow room for the riser rail to be fitted later (see dimensions on page 6). Prepare the wall with 2 copper pipes at 150mm centres.
- Page 9 Installation - Offset connectors Installation - Quick guide Note: There are two options for installing your valve, using offset connectors (below) or quick fit connectors (see page 13). Offset connector ½” connector Riser rail connection Offset connector Cold Cover Rubber filter/washer Locking nuts Before installing your new mixer, flush through the pipe work to ensure removal of debris, turn off the water supply.
- Page 10 Installation - Quick guide Installation - Quick guide...