1. Manuals
  2. Brands
  3. IBM Manuals
  4. Server
  5. e Server iSeries 825
  6. Manual

IBM e Server iSeries 825 Manual

Removable media device
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
ERserver
iSeries 270, 800, 810, 820 or 825
Removable Media Device
Version 5

Advertisement

Table of Contents
loading

Related Manuals for IBM e Server iSeries 825

Summary of Contents for IBM e Server iSeries 825

  • Page 1 ERserver iSeries 270, 800, 810, 820 or 825 Removable Media Device Version 5...
  • Page 3 ERserver iSeries 270, 800, 810, 820 or 825 Removable Media Device Version 5...
  • Page 4 “Notices,” on page 37. Fourth Edition (August 2005) ® This edition applies to version 5, release 3, modification 0 of IBM Operating System/400 (product number 5722–SS1) and to all subsequent releases and modifications until otherwise indicated in new editions. This version does not run on all reduced instruction set computer (RISC) models nor does it run on CISC models.

  • Page 5: Table Of Contents

    Details: Install removable media devices with 825 Electronic Emission Notices . . 42 powered on . . 20 Federal Communications Commission (FCC) Install removable media devices with 825 powered statement . . 42 . 22 © Copyright IBM Corp. 2000, 2005...
  • Page 6 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3...

  • Page 7: Chapter 1. Removable Media Device

    IPL your system, and verify your hardware configuration. You can choose to perform these tasks yourself or contact IBM(R) or an authorized service provider to make arrangements for them to perform the tasks for a fee. Should you encounter difficulties when performing a task, contact your authorized dealer or service provider.
  • Page 8 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3...

  • Page 9: Chapter 2. Before You Begin

    __ 4. If there are incorrect, missing, or visibly damaged parts, contact one of the following: v Your authorized service provider ® v In the United States: IBM Rochester Manufacturing Automated Information Line (R–MAIL) at 1–800–300–8751 v In countries outside of the United States: Use the following Web site to locate your service and support numbers: http://www.ibm.com/planetwide...
  • Page 10 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3...

  • Page 11: Chapter 3. Replace Removable Media Devices In Iseries 270, 800, 810, Or

    __ 6. Disconnect the signal (larger connector) and power (smaller connector) cables from the back of the device. Access to these connectors is from the side of the system unit. __ 7. Pull the two latches that secure the device to the system unit frame forward until they stop. © Copyright IBM Corp. 2000, 2005...
  • Page 12 __ 8. Remove the device by sliding it forward and out of the system unit. You may need to remove the filler blank above the control panel. __ 9. Place the device in a static protective bag. __ 10. Follow the steps in “Details: Install removable media devices in iSeries 270, 800, 810, or 820” on page 7 to install the new device.

  • Page 13: Chapter 4. Install Removable Media Devices In Iseries 270, 800, 810, Or

    __ 2. Is the device you are installing an optical device? Yes: Continue with the next step. No: Go to step 4 on page 8. __ 3. Refer to the following figures to place the optical device unit address jumpers © Copyright IBM Corp. 2000, 2005...
  • Page 14 Figure 1. 6321 CD-ROM optical unit jumpers for location D07 (Models 270, 800 and 810) and D13 (Model 820) Figure 2. 6330 DVD-RAM optical unit jumpers for location D07 (Models 270, 800 and 810) and D13 (Model 820) Figure 3. DVD-ROM optical unit jumpers for location D07 (Models 270, 800 and 810) and D13 (Model 820) __ 4.

  • Page 15: Completing The Installation

    __ 5. Push in the blue latches to secure the device to your system unit. __ 6. Plug the power cable into the smaller connector on the back of the removable media device. __ 7. If you are not replacing an existing removable media device, you need to remove the tape from the end of the cable.
  • Page 16 __ 3. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the products that attach to the system. It is the customer’s responsibility to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (RSFTD201) Plug the following power cords into an electrical outlet.
  • Page 17 __ f. Press the Increment/Decrement push button until S appears in the Function/Data display __ g. Press the Enter push button on the control panel. __ h. Press the Mode Select button until the Normal indicator (OK) is illuminated. __ i. Press the Enter push button on the control panel. __ j.
  • Page 18 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3...

  • Page 19: Chapter 5. Replace Removable Media Devices In Iseries 825

    Attention: Failure to follow these instructions could result in damage to the removable media device or to the system unit and could result in loss of data. To perform the concurrent replacement procedure, follow these steps: © Copyright IBM Corp. 2000, 2005...
  • Page 20 1. If possible, use a wrist strap to prevent electrostatic discharge from damaging your hardware. If you do not have a wrist strap, touch a metal surface of the system or expansion unit before installing or replacing hardware. If you received the 2209 Disposable Wrist Strap, follow these steps: __ a.

  • Page 21: Replace Removable Media Devices With 825 Powered Off

    12. When the light begins to blink rapidly, you will have nine seconds to remove the device. 13. Press Enter on the console. 14. When the light starts blinking, after the one minute delay, squeeze and pull both handles on both sides of the device toward you.
  • Page 22 Note: Follow the same precautions you would use without the wrist strap. The 2209 Disposable Wrist Strap is for static control. It will not increase or decrease your risk of receiving electric shock when using or working on electrical equipment. __ 4.
  • Page 23 __ 7. Follow the instructions in “Details: Install removable media devices with 825 power off” on page 22 to install the new removable media device. Chapter 5. Replace removable media devices in iSeries 825...
  • Page 24 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3...

  • Page 25: Chapter 6. Install Removable Media Devices In Iseries 825

    Note: Follow the same precautions you would use without the wrist strap. The 2209 Disposable Wrist Strap is for static control. It will not increase or decrease your risk of receiving electric shock when using or working on electrical equipment. © Copyright IBM Corp. 2000, 2005...

  • Page 26: Install Removable Media Devices With 825 Power On

    __ 4. Pull out the removable media filler bezel from the location in which you are installing the new device. View video. This procedure gives you the steps you need to install removable media devices in your 825 system. Your system can either be powered off (nonconcurrent) or powered on (concurrent) when you install the removable media device.
  • Page 27 __ 3. Hold the device with the button in the upper right for tape units or lower right for CD-ROMs. __ 4. Refer to Figure 5 and support the bottom of the removable media device as you slide it half way into the selected position.

  • Page 28: Install Removable Media Devices With 825 Powered Off

    __ 15. At the Hardware Service Manager display, press F6 to print the configuration list if you have a printer. You or a service representative may refer to the configuration list in the future. __ 16. Install the front cover. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the products that attach to the system.
  • Page 29 Figure 6. Installing the removable media device __ 7. Install the front cover. DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the products that attach to the system. It is the customer’s responsibility to ensure that the outlet is correctly wired and grounded to prevent an electrical shock.
  • Page 30 __ h. Press the Mode Select button until the Normal indicator (OK) illuminated. __ i. Press the Increment/Decrement push button until 01 appears in the Function/Data display. __ j. Press the Enter push button on the control panel. 01 B S with Normal indicator (OK) illuminated should appear in the Function/Data display.

  • Page 31: Chapter 7. Replace Concurrent Removable Media Backplane

    Wrist Strap is for static control. It will not increase or decrease your risk of receiving electric shock when using or working on electrical equipment. __ 5. Remove the media devices from the unit. __ 6. Remove the screws A . © Copyright IBM Corp. 2000, 2005...
  • Page 32 __ 7. Slowly slide the removable media enclosure from the system. __ 8. Disconnect the signal and power cables from the back of the removable media enclosure. __ 9. Follow the steps in “Details: Install concurrent removable media backplane” on page 28 to install the removable media backplane.

  • Page 33: Chapter 8. Install Concurrent Removable Media Backplane

    Note: Follow the same precautions you would use without the wrist strap. The 2209 Disposable Wrist Strap is for static control. It will not increase or decrease your risk of receiving electric shock when using or working on electrical equipment. © Copyright IBM Corp. 2000, 2005...

  • Page 34: Details: Install Concurrent Removable Media Backplane

    __ 5. Remove the media devices from the unit. __ 6. Remove the screws A . __ 7. Slowly slide the removable media enclosure from the system. __ 8. Disconnect the signal and power cables from the back of the removable media enclosure. __ 9.
  • Page 35 DANGER An electrical outlet that is not correctly wired could place hazardous voltage on metal parts of the system or the products that attach to the system. It is the customer’s responsibility to ensure that the outlet is correctly wired and grounded to prevent an electrical shock. (RSFTD201) __ 7.
  • Page 36 __ h. Set the time delay for one minute—01. (Do not press Enter at this time.) __ i. When the light begins to blink rapidly, you will have nine seconds to remove the device. __ j. Press Enter on the console. __ k.

  • Page 37: Power Down The System Unit

    __ 5. Unplug any power cords, such as printers and displays, from electrical outlets. __ 6. Unplug the system unit power cord from the electrical outlet. © Copyright IBM Corp. 2000, 2005...
  • Page 38 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3...

  • Page 39: Unit Covers

    820 unit—Remove the left side cover (view from back) by loosening the thumbscrews and sliding the cover from front to back until it stops. __ 3. Pull the cover out. __ 4. Remove the front cover. © Copyright IBM Corp. 2000, 2005...
  • Page 40 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3...

  • Page 41: 270, 800, Or 810 Unit In A Rack

    270, 800, or 810 unit in a rack 1. Press latches B and pull the server out using the handle C . 2. Remove the front cover. Refer to step 4 on page 33. 3. Remove the left side cover (view from front). Refer to step 3 on page 33. Unit Covers...
  • Page 42 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3...

  • Page 43: Appendix. Notices

    Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead.

  • Page 44: Trademarks

    All statements regarding IBM’s future direction or intent are subject to change or withdrawal without notice, and represent goals and objectives only. All IBM prices shown are IBM’s suggested retail prices, are current and are subject to change without notice. Dealer prices may vary.

  • Page 45: Terms And Conditions For Downloading And Printing Publications

    Publications or any information, data, software or other intellectual property contained therein. IBM reserves the right to withdraw the permissions granted herein whenever, in its discretion, the use of the Publications is detrimental to its interest or, as determined by IBM, the above instructions are not being properly followed.

  • Page 46: Electronic Emission Notices

    Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.
  • Page 47 Dieses Gerät ist berechtigt in Übereinstimmung mit Dem deutschen EMVG vom 9.Nov.92 das EG–Konformitätszeichen zu führen. Der Aussteller der Konformitätserklärung ist die IBM Germany. Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse A. Für diese von Geräten gilt folgende Bestimmung nach dem EMVG: Appendix.

  • Page 48: Electronic Emission Notices

    Dieses Genehmigungsverfahren ist von der Deutschen Bundespost noch nicht veröffentlicht worden. Electronic Emission Notices The following Statement applies to this IBM product. The statement for other IBM products intended for use with this product will appear in their accompanying manuals.
  • Page 49 This product is in conformity with the protection requirements of EC Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards.
  • Page 50 45xx, 46xx 270, 800, 810, 820, 825 Removable Media Device V5R3...
  • Page 52 Printed in USA...

This manual is also suitable for:

E server iseries 800E server iseries 270E server iseries 810E server iseries 820

Table of Contents