Page 3
Device overview The following buttons are located beside the display: 1 On/Off switch: • Long press (longer than 3 sec- onds): Switches the device on/off. • Short press: Switches the screen on/off. (Energy-saving mode) 2 MENU: • Long press (longer than 3 sec- onds): Opens the main menu of 4 Headphone jack the device.
Page 4
Device overview The underside features the following The rear side of the device features controls: the following element: 7 USB connection 9 TMC antenna connection 8 Connects the Lucca with the suction cup holder...
Contents Device overview .......2 Switching on/off ....16 Switching on ......16 About these instructions ..10 Activating the idle state ..... 16 Safety notes ......10 Switching off ......16 Safety notes for navigation ... 10 The menu button ....17 Safety notes for handling Quick settings ......
Page 6
Contents Navigation ......23 Additional functions ....32 Point of interest at a specifi c General notes about location ........33 the navigation ....... 23 Special national destination ..35 Starting the navigation ....24 Copying a destination from Entering a destination ....24 the map.........
Page 7
Contents Route planning with stages ...45 Destination guidance .....52 Disturbed GPS reception ... 53 Planning a route ......45 Quitting the destination Editing a route ......46 guidance ........53 Changing the order of Reaching the place of route points ....... 46 destination .........
Page 8
Contents Map display during Basic settings of the Lucca ..65 destination guidance ....58 Settings ........65 Navigation tools ......58 Language ........66 Route information ......59 Home address ......66 Map information ......67 Signpost information (exit signs) .. 59 Route information ......
Page 9
Contents GPS mode of operation ..71 Technical data ......79 Using the SD/MMC card ..72 Disposal of old unit ....80 Service ........81 Preparation ........72 Warranty ........81 Inserting the SD/MMC card ..73 Frequently asked questions / Removing the SD/MMC card..73 FAQ .........82 MP3 player ......73 Starting the MP3 player ....
About these instructions Safety notes About these instructions Safety notes The menus and buttons used in illus- For your personal benefi t, carefully trations feature the English language. read the following safety notes and In order to make these instructions warnings before operating your Luc- more comprehensible, the device- ca for the fi...
Safety notes Notes: Safety notes for handling • Routes are best planned before the Lucca starting your trip. If you want to enter a new route while on the Caution: road, please head for the next Protect the device against moisture parking or rest area! since it is not waterproof and not •...
Initial startup Initial startup of Lucca Lucca scope of delivery The scope of delivery contains the When you switch on the Lucca for following components: the fi rst time, a dialogue appears and asks which language the Lucca should use. (For further details, please read •...
Initial startup Protective screen fi lm Setting the language Prior to the initial use, remove the The Lucca uses US English as the protective fi lm from the screen. standard language for the menus and voice output. When you switch Switching on the Lucca on the Lucca for the fi...
Notes: – : The device is supplied by • Use only a charger approved by an external power source. The Blaupunkt. Please contact your battery is fully charged. specialised Blaupunkt dealer. – : The device is supplied by • Do not discard any batteries an external power source.
Installation in the vehicle ➜ Installation in the Press the suction plate of the suc- tion cup against the windshield. vehicle ➜ Push the lever on the suction cup towards the glass. For temporary installation in a vehi- ➜ cle, the Lucca features a suction cup The track for mounting the Lucca holder to attach it to the windshield.
Installation in the vehicle Switching on/off Installing Lucca in the suction cup Switching on/off holder Switching on The suction cup holder features a track for mounting the Lucca on the ➜ Briefl y press the On/Off switch. inside. The device switches on and dis- ➜...
The menu button The menu button The INFO button Prerequisite: Quick settings • A destination guidance is active. In the Quick Settings menu volume ➜ Touch the Info button in the Quick and brightness can be adjusted. The Settings menu. Quick Settings menu can be called at The last voice instruction is re- any time, regardless of the currently...
The menu button Operating the navigation menus • Power Saving Operating the – Touch the Power Saving button. navigation menus The Power Saving menu is dis- played. Software keyboard – Backlight Time Out: Touch the If text entries are required, the touch- setting under this menu item to screen displays a software keyboard.
Operating the navigation menus To enter numbers, such as a postal List code, In many cases, you can display lists ➜ touch the button from which you can select an entry. This is the case, for example, if you To return to the character entry mode, do not enter the complete name of a place during the entry.
Operating the navigation menus Buttons ➜ : Touch this button to scroll down in the list by one page These buttons are located on all men- (5 elements). us of the Lucca: ➜ To scroll in the list by several pag- ➜...
Operating the navigation menus Information From the Navigation menu, you can display the current traffi c reports and the GPS status at any time. Traffi c reports Your Lucca is supplied with traffi c reports via TMC (traffi c information data channel).
Operating the navigation menus GPS status The GPS status menu contains informa- tion about your current position and your current speed. In addition, you can also save your current position. ➜ In the Navigation menu, touch the More button. The following window displays: •...
Operating the navigation menus Navigation • HDOP – Horizontal Dilution of Navigation Precision: Indicates the qual- ity of the positioning. In theory, General notes about the values from 0 to 50 are possible, navigation The following applies: The lower The use of the Lucca is at your own the value, the more precise the risk.
Navigation Starting the navigation The Navigation menu allows access to all the functions of the navigation. ➜ Switch on the device with the On/ Off switch. Entering a destination ➜ In the main menu, touch the Navi- ➜ Touch the Destination entry but- gation button.
Navigation Settings GPS Info ➜ ➜ Touch the Settings button to ad- Touch the GPS Info button to ob- just the settings of your Lucca. tain information about the current GPS status and about your current For further details, read the section position.
Navigation Setting the time zone Note: The selection is facilitated by the ➜ In the Navigation menu, touch the display of the capitols in the re- Settings button. spective time zone. The Settings menu displays. ➜ ➜ Touch the button repeatedly un- If daylight savings time currently applies to your position, touch the til the Time zone button appears.
Navigation Entering a destination This section contains information about the different methods for en- tering, selecting and managing desti- nations with the Lucca. The chapter "Destination guidance" describes how to start the destina- tion guidance. Entering a destination With the Lucca, you can enter or se- ➜...
Page 28
Navigation is in a different country than the previous one, you must re-enter the country. ➜ In the main menu, touch the Navi- gation button. The Navigation menu is displayed. ➜ Touch the Country button. The list of countries displays. ➜...
Navigation Note: Note: You can only select countries which If the country containing your des- are at least partially displayed on tination is not displayed in the top the currently loaded map. line (see country code), touch the button and select the cor- Entering a destination address rect country.
Navigation Note: For further details, read the chapter "Specifying routing options". How to save a defi ned destination is described in the chapter "Saving • Show: one of the last destinations". – Select this button to view the address entered on the map. Additional functions For further details, read the chapter ➜...
Page 31
Navigation ➜ ➜ In the Navigation menu, touch the Touch the ... nearby button. Destination entry button. The submenu displays. The Destination entry menu is dis- played. ➜ Touch the Point of interest but- ton. The Point of interest menu is dis- played.
Navigation ➜ ➜ Touch the subcategory fi eld If you desire more detailed infor- and select the subcategory mation about the point of interest, (e.g. a petrol station of a specifi c touch the More button, followed brand) from which you want to by Show details.
Navigation The following additional functions The Destination entry menu is dis- are available: played. ➜ In the menu, touch the Point of • Routing options: interest button. – The routing options for the next The Point of interest menu is dis- destination guidance can be played.
Page 34
Navigation Only those categories are avail- able for selection for which points of interest can be located in the specifi ed town. ➜ Touch the Subcategory fi eld and select the subcategory (e.g. "museum" or "theatre") from which you want to look for points of interest.
Navigation ➜ Touch the entry of the point of in- terest to which you want to navi- gate. ➜ If you desire more detailed infor- mation about the point of interest, touch the More button, followed by Show details. ➜ Touch the OK button to accept the selected point of interest.
Navigation ➜ twice and select the correct coun- If you desire more detailed infor- try. How to select a country is de- mation about the point of interest, scribed in the chapter "Entering touch the More button, followed the destination country". by Show details.
Navigation – Move: The map can be moved in the move mode. For this pur- pose, touch the map, hold the pen or your fi nger pressed and move the map area in the de- sired direction. ➜ Touch the town (street or point of interest) to be defi...
Page 38
Navigation • Touch the Search nearby button to search for a point of interest in the vicinity of the selected desti- nation. • Touch the Interim dest. button to add the selected destination to a route (as the next stage to be approached).
Navigation Copying the destination from the favourites The favourites contain all the destina- tions you saved using the Save but- ton. You can perform the following in this menu: • Accepting destinations for the destination guidance • Renaming destinations ➜ Touch the desired destination.
Navigation additional functions in the Favour- Copying one of the last ites menu. destinations The list of additional functions dis- The destinations approached last are plays. automatically stored in the Last desti- nations list. The following additional functions You can perform the following in this are available: list: •...
Navigation The following additional functions are available: • Show details: – Touch this button to show the address of the selected desti- nation. • Delete entry: – Touch this button to delete the marked destination. • Delete all: ➜ Select the desired destination. –...
Navigation Managing destinations ➜ In the main menu, touch the Navi- Managing destinations gation button. Two lists are available in which indi- The Navigation menu is displayed. vidual destinations are saved: ➜ Touch the Home button. • Favourites The route calculation is performed •...
Managing destinations ➜ Enter a name for the destination. ➜ Touch the OK button. The destination is saved in the Favourites. Saving one of the last destinations Prerequisite: • You opened the Last destinations list as described in the chapter "Copying one of the last destina- tions".
Managing destinations ➜ ➜ Enter a new name for the destina- Touch OK to delete the destination. tion. - or - ➜ Touch the OK button. ➜ Touch to not delete the des- tination. The destination is renamed. Deleting a destination Deleting the complete list with destinations Prerequisite:...
Route planning ➜ Route planning with Touch the Add button to enter the fi rst route point. stages The Destination entry menu is dis- played. You can also perform the route plan- ning in the comfort of your home, ➜ Defi...
Route planning ➜ Editing a route Touch the Route point up button. The Itinerary menu is displayed You can insert additional route points again. The selected route point is in the routes at any time, change the moved up one position in the route order of route points or display the list.
Route planning Deleting a complete route list Calculating a route If you want to delete all the route You can use a planned route for the points from the current route list: destination guidance or calculate be- ➜ fore the trip to gain an overview of Touch the More button.
Route planning point entered is the starting point of Showing the route on the map the route. ➜ Touch the Show button to display the entire route on the map. After calculating the route, you can view it on the map or take a virtual trip. The map is displayed.
Specifying routing options Specifying routing options In the Routing options menu, you can defi ne the speed profi le of your vehi- cle, select the type of routing and ex- clude certain streets from usage. The routing options are retained for every subsequent destination guidance.
Specifying routing options TMC function • Short TMC function – This option calculates The Traffi c Message Channel (TMC) shortest route for the kilome- supplies your Lucca with traffi c re- tres to be travelled. ports that are broadcast by the radio ➜...
TMC function ➜ Switching on the TMC Touch the button until the screen with the TMC button ap- function pears. The TMC function is activated in the ➜ Touch the TMC button. Routing options menu (see "Specify- ➜ Touch the Route modifi cation but- ing routing options"): ton to change between the two ➜...
Destination guidance Destination guidance ➜ Touch the buttons More and in succession to show or hide Prerequisite: additional buttons. • You entered a place of destination as described in the chapter "Enter- ing a destination". - or - • You selected a place of destination from the Favourites as described in the chapter "Copying the destina- tion from the favourites".
Destination guidance Disturbed GPS reception Quitting the destination guidance ➜ A message notifi es you if no adequate Touch this button to quit GPS signal is received. the destination guidance. A confi rmation dialogue appears. ➜ Touch OK to quit the destination guidance.
Working with the map Working with the map Touching the map ➜ Briefl y touch the map to display additional functions. Map operation Depending on whether you are cur- In this section you learn which in- rently in an active destination guid- formation and which processing op- ance or only display the map, only tions are available in the map view.
Working with the map In map view without GPS reception • Fix map Fix position • Showing/hiding buttons This button is only active during a – More destination guidance. Touch this This button allows you to hide button to fi x the map or the posi- the additional buttons to gain tion.
Working with the map – Zoom: In the zoom mode, you • 3-D view can enlarge or reduce the – Touch this button to display map section. the map in a three-dimensional Enlarge: Draw a diagonal starting representation from a bird's at the top left corner.
Working with the map All other buttons are effective only during the destination guidance: • Block road: For further details, read the section "Blocking route segments". • Interim dest.: For further details, read the section "Inserting an in- terim destination". •...
Map display during destination guidance Map display during Navigation tools The left and lower area of the map dis- destination guidance play the following navigation tools: During a destination guidance, the map display shows different navi- gation tools, route information and signpost information.
Map display during destination guidance – If you come closer to the ac- – : Estimated time of tion location, a yellow bar is arrival. displayed to the right of the – : Estimated remaining large arrow fi eld instead of the travel time.
Map display during destination guidance Speed limit The right area of the map displays the speed limit that may apply: Note: This information can only be dis- played if it is part of the map ma- terial. Map information ➜ In the Settings menu, touch Map Activating additional map information.
Map display during destination guidance ➜ Touch the OK button to save your The corresponding information for settings. the next stage (upper area) and the complete route (lower area) is - or - displayed on the map. ➜ Touch the button to not save the settings and to return to the Settings menu.
Map display during destination guidance ➜ ➜ Touch the OK button to save your Touch the Show traffi c signs but- settings. ton to change between the modes "Always", "On speeding only" or - or - "Never". ➜ Touch the button to not save the settings and to return to •...
Additional functions Additional functions The menu with the additional func- tions displays. during the destination guidance You can perform the following during destination guidance: • Inserting an interim destination • Skip a route point (Approaching the next destination) • Block a route segment Inserting an interim ➜...
Additional functions Blocking route segments Note: Blocking route You can also select the interim segments destination directly from the map as described in the section "Copy- Manual blocking ing a destination from the map". You have the option of manually Next, touch the Interim dest.
Blocking route segments Basic settings of the Lucca ➜ Select the Block road entry. Basic settings of the The Block road menu is displayed. Lucca Settings You can perform settings in the Lucca for the following areas: • Language • Home address •...
Basic settings of the Lucca ➜ ➜ In the Navigation menu, touch the Touch the Home address button. Settings button to confi gure the The Home address menu is dis- Lucca. played. ➜ If you changed the settings in the Set- Touch the Enter your home ad- tings menu, dress button.
Basic settings of the Lucca ➜ Map information If you activate the entries for Stage Point, the map shows the informa- In the Map information menu, you tion up to the next route point. can perform the following settings: • Info bar Note: –...
Basic settings of the Lucca • Automatic activated: The Lucca should be displayed during the desti- nation guidance or not. automatically guides you from the fi rst to the last stage. ➜ Touch the Show traffi c signs but- ton to activate or deactivate the •...
Basic settings of the Lucca ➜ Touch the Warning in urban areas Auto mode button to change the value or to In the Auto mode menu, you can per- set it to Never. form the following settings: • Warning in rural areas: •...
Basic settings of the Lucca driving direction by default dur- Format ing a destination guidance with In the Format menu you can specify 2-D view. which units of measure should be used for times and distances and the Time zone language to be used for the menus In the Time zone menu, you can set and voice output of the Lucca.
Basic settings of the Lucca GPS mode of operation Factory settings GPS mode of operation In the Factory settings menu, you can The Global Positioning System (GPS) reset the navigation software to the was developed in the 70s by the US factory settings.
GPS mode of operation Using the SD/MMC card If the Lucca receives the signals from Using the SD/MMC card at least 3 satellites, it can determine You can use an SD/MMC card with its position and display it on the map. the Lucca for the following: This position can then be used as the •...
Using the SD/MMC card MP3 player MP3 player Audio fi les Image fi les (MP3 player) (Picture Viewer) You can use the Lucca to play audio fi les from an SD/MMC card. The Luc- MP3 fi les JPG (max. 2.2 mill. ca recognises the formats MP3, WMA (ID3 tags version pixel)
MP3 player ? Playing the previous/next MP3 fi le ➜ Touch the Music Player button. The MP3 menu is displayed. @ Ending playback (Stop) Operating the MP3 player A Interrupting playback (Pause)/ Continuing playback In the MP3 menu, you can operate the MP3 player and calling the MP3 list.
MP3 player Picture Viewer Picture Viewer You can view images with the Lucca that are stored on a SD/MMC card. The Lucca recognises image data in the format JPG, GIF and BMP. The chapter "Using the SD/MMC card" provides information about the use and preparation of the card.
Picture Viewer The Picture Viewer menu and the Slide show fi rst recognised image fi le are dis- If you touch the SLIDE button in the played. Picture Viewer, all images are dis- played in 3 second intervals. Operating the Picture At the end of the slide show, a refer- Viewer ence appears whether the fi...
Picture Viewer Installing the map material Full-screen mode Installing the map If you touch the FULL button in the material Picture Viewer, the current image is The map material of the country in displayed in full-screen mode. Use which the Lucca was purchased is the arrow symbols to change to the preinstalled in the memory of the previous or next image fi...
Installing the map material Using map material with the Removing the SD/MMC card Lucca ➜ Carefully push on the SD/MMC card in the slot until it disengages. ➜ Switch on the Lucca by pressing the The SD/MMC card is ejected from On/Off switch for a few seconds.
CE 5.0 state-of-the-art, Blaupunkt offers soft- CPU: Atlas II Dual Core ware downloads at regular intervals. Processor (300 MHz) They can be found on the Blaupunkt Main memory: Internet site www.blaupunkt.com. 64 MB DRAM 512 MB NAND Flash Unit size (mm): 115 (W) x 80 (L) x 25 (H) Weight (g): approx.
Technical data Disposal of old unit Picture Viewer: Disposal of old unit JPG (max. 2.2 mill. pixel), (EU countries only) GIF (max. 2.2 mill. pixel), BMP (max. 13 MB) Do not dispose of your old unit in SD/MMC card: the household trash! max.
European Union, In case your Lucca has to be sent to the warranty terms issued by our re- Blaupunkt for service you can order spective responsible domestic agen- a pick-up service for your device on cy are valid. The warranty period for the internet.
Frequently asked Belgium, Netherlands, Austria, Swit- zerland, France, Italy, Spain and questions / FAQ Czech Republic. Hungary and Poland plan to introduce it. Why does the Lucca require GPS Which cards can I use? reception? Commercial SD or MMC cards. The system must know where it is lo- cated or where it is moving.
Page 83
Can the navigation software be via the USB-port with your PC and ini- tiate the loading process via menu. changed? Yes. Simply insert the SD/MMC card in the SD/MMC card slot or use the How long does the loading take from USB connection, and you can imme- the SD/MMC card to the internal diately navigate with the new data.