1. Manuals
  2. Brands
  3. AntennaTek Manuals
  4. Antenna
  5. Signal Commander LPDA 200
  6. Owner's manual

AntennaTek Signal Commander LPDA 200 Owner's Manual

Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

OWNER'S MANUAL
THIS MANUAL CONTAINS
INSTRUCTIONS FOR:
- INSTALLATION
- OPERATION
- TROUBLESHOOTING
- EXPLODED PARTS DRAWING
- WARRANTY
AntennaTek, Inc.
425 S. Bowen, #4
Longmont, CO 80501
(303)772-9591
www.antennatek.com
More information https://www.caravansplus.com.au
LPDA 200
FAX (303) 774-9533
Form: manv12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Signal Commander LPDA 200 and is the answer not in the manual?

Questions and answers

Related Manuals for AntennaTek Signal Commander LPDA 200

Summary of Contents for AntennaTek Signal Commander LPDA 200

  • Page 1 OWNER'S MANUAL THIS MANUAL CONTAINS LPDA 200 INSTRUCTIONS FOR: - INSTALLATION - OPERATION - TROUBLESHOOTING - EXPLODED PARTS DRAWING - WARRANTY AntennaTek, Inc. 425 S. Bowen, #4 Longmont, CO 80501 (303)772-9591 FAX (303) 774-9533 www.antennatek.com Form: manv12 More information https://www.caravansplus.com.au...

  • Page 2: Section I Installation Instructions

    SECTION I INSTALLATION INSTRUCTIONS This manual contains information on the following Signal Commander® LPDA models and accessories; the model you have purchased is clearly marked on the front of this manual. MODEL 200 Amplified Antenna with 2nd TV & Cable TV Ready TOOLS AND SUPPLIES REQUIRED: INSTALLATION KIT CONTENTS: Mechanical Installation...

  • Page 3: Installation

    2. Installation WARNING! Step 6: Caulk the bottom of the baseplate with a liberal amount of non-hardening sealing compound, Electricity Kills! then position and attach the lift mechanism to the roof Power lines may be overhead. with ten #8x1" pan head sheet metal screws. Seal Care must be taken when installing or the edges of the base plate and the top of the screws raising the antenna.
  • Page 4 Step 7: Mount antenna head to lift arm mechanism using two 1/4"x1-5/8" grove pins and “E” clips. E-Clips “E” Clips Groove Pins Step 11: Assemble rotation handle, spring, washer and Step 8: Connect the coaxial cable to the antenna head elevating handle (See illustration).
  • Page 5 with wire nuts and insulating tape. Step 13: The power supply is designed for instal- lation in any standard electrical box. To mount the CAUTION: The red wire is positive (+) power supply cut a hole in the wall and install the The black wire is negative (-) electrical box.Place the power supply switch in the "OFF"...

  • Page 6: Section Ii Operating Instructions

    SECTION II OPERATING INSTRUCTIONS 1. To Raise & Rotate Antenna 2. To Lower Antenna A : Rotate elevation handle clockwise to raise the A: Pull rotation handle down to disengage gear from antenna. Resistance will be felt in the handle when ceiling plate and rotate the antenna until the pointer the antenna is completely extended.

  • Page 7: Section Iv Exploded Parts Diagram

    SECTION IV EXPLODED PARTS DIAGRAM Distributors: Australia / New Zealand Dometic Australia 1 800 21 21 21 Email: sales@dometic.com.au Web: www.dometic.com.au Assembly SIMB DESCRIPTION P/N 019726 Head Assembly for LPDA 902201 Groove Pin 030195 E-Clip 030197 Upper Arm for LPDA 065603 Lower Arm for LPDA 065604...

  • Page 8: Section V Warranty

    Company is available as an optional, and return the product to the Company: customer paid service. AntennaTek, Inc., 425 S. Bowen St., #4, Longmont, Colorado 80501. 5. What is not covered under this warranty? D. Use reasonable care in the maintenance, operation, A.

Table of Contents